Installation Guide

ManualsBrandsSchneider Electric ManualsKitchen30 Amp Wiser Load Control Relay

Instruction Bulletin

S1B14484

Rev. 02, 03/2013

Replaces S1B14484 Rev. 01, 08/2011

Wiser™ Load Control Relays

Installer’s Guide

Retain for future use.

™

Relay Catalog No. Rating

EER42300 5 A

EER42200 30 A

ENGLISH

Safety Precautions

This load control relay must be installed in accordance with the National

Electrical Code

and applicable local codes. A qualified, licensed electrician

must install this relay.

This load control relay can only be used in an installation with an approved

home management portal. Stand-alone installations are not supported.

Contact your local Schneider Electric representative for more information.

Installation Turn off all power supplying this relay before working on it. See the Safety

Precautions above.

The relay is suitable for indoor or outdoor use. The relay has four feet for

installing it on the mounting surface. See Figure 2 (5 A) or Figure 3 (30 A)

on page 2.

Figure 1: Load Control Relay

DANGER

HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH

• Apply appropriate personal protective equipment (PPE) and follow safe

electrical work practices. See NFPA 70E.

• This equipment must only be installed and serviced by qualified

electrical personnel.

• Turn OFF all power supplying this equipment before working on or

inside the equipment.

• Always use a properly rated voltage sensing device to confirm that

power is off.

• Replace all devices, doors, and covers before turning on power to this

equipment.

• Petroleum-based paints, solvents, or sprays can cause plastic to

degrade. Do not allow petroleum-based paints, solvents, or sprays to

contact the nonmetallic parts of this product.

• Before starting a wiring installation or addition, consult a local building

or electrical inspector for current National Electrical Code

requirements. Local codes vary, but are adopted and enforced to

promote safe electrical installations. A permit may be needed to do

electrical work, and some codes may require an inspection of the

electrical work.

• This equipment is not suitable for use in the corrosive environments

present in agricultural buildings. See NEC 547 or CEC 2-400.

• There are no serviceable parts in this load control relay.

Failure to follow these instructions will result in death or serious

injury.

Summary of content (12 pages)

PAGE 1
S1B14484 Rev. 02, 03/2013 Instruction Bulletin Wiser™ Load Control Relays Installer’s Guide Relay Catalog No. ENGLISH Replaces S1B14484 Rev. 01, 08/2011 Rating EER42300 5A EER42200 30 A Retain for future use. Safety Precautions Figure 1: Load Control Relay DANGER HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH • Apply appropriate personal protective equipment (PPE) and follow safe electrical work practices. See NFPA 70E.
PAGE 2
Wiser™ Load Control Relays Features and LED Indications S1B14484 Rev. 02, 03/2013 ENGLISH For best radio frequency (RF) performance, mount the relay to a nonmetallic surface or with the top of the relay 1.5 inches (39 mm) or more above a metallic surface. Use screws (not provided) appropriate for the mounting surface. Do not over-tighten the screws. Figure 2: 5 A Relay LED indicator Up Mounting foot (x 4) Orange White Line Orange Orange/Orange Switched control circuit 5 A @ 240 Vac gen.
PAGE 3
Joining a ZigBee® Network Wiser™ Load Control Relays Joining a ZigBee® Network Table 1: LED Status Indications LED State Rate State Indication Off 0% On • • • Relay is malfunctioning or connected improperly. Relay has no power. Relay is off. On 100% On • The load is turned on. Short Blink On for 1/10 of a second, once per second • • The load is turned off. Load shedding is in progress. Long Blink On for 1/2 of a second, • once per second Relay is not on a network and is idle.
PAGE 4
Wiser™ Load Control Relays Instruction Bulletin S1B14484 Rev. 02, 03/2013 Table 2: Radio Specifications (continued) ENGLISH Simple Metering Cluster: All Mandatory Commands All Mandatory Attributes Price Cluster: All Mandatory Commands Product Support The Schneider Electric Customer Care Center (CCC) is your single point of contact for information about the Wiser Load Control Relay. Qualified personnel are available to answer your customer service and technical support questions.
PAGE 5
S1B14484 Rev. 02, 03/2013 Boletín de instrucciones Reemplaza S1B14484 Rev. 01, 08/2011 Relevadores de control de carga Wiser™ Guía para el encargado de la instalación Conservar para uso futuro. No.
PAGE 6
Relevadores de control de carga Wiser™ Instalación Instalación S1B14484 Rev. 02, 03/2013 Desenergice el relevador antes de realizar cualquier trabajo en él. Consulte las precauciones de seguridad delineadas anteriormente. El relevador es adecuado para su uso en interiores o exteriores. El relevador tiene cuatro provisiones para ser instalado sobre una superficie de montaje. Consulte la figura 2 (5 A) o 3 (30 A).
PAGE 7
S1B14484 Rev. 02, 03/2013 Relevadores de control de carga Wiser™ Características e indicaciones de LED Características e indicaciones de LED Ubicaciones de LED y sensor de imán MA GN ET Tabla 1: Indicaciones de estado de LED Estado de Frecuencia LED Indicación de estado • SE NS OR Sensor de imán LED Conexión a una red ZigBee® • • El relevador está funcionando inapropiadamente o conectado incorrectamente. El relevador no tiene alimentación. El relevador está apagado.
PAGE 8
Relevadores de control de carga Wiser™ Boletín de instrucciones S1B14484 Rev.
PAGE 9
S1B14484 Rév. 02, 03/2013 Directives d’utilisation Remplace S1B14484 Rév. 01, 08/2011 Relais de contrôle de charge WiserMC Guide de l'installateur No de cat. du relais Val. nom. EER42300 5A EER42200 30 A À conserver pour usage ultérieur. Mesures de sécurité Figure 1 : Relais de contrôle de charge DANGER RISQUE D'ÉLECTROCUTION, D'EXPLOSION OU D'ÉCLAIR D'ARC • Portez un équipement de protection personnelle (ÉPP) approprié et observez les méthodes de travail électrique sécuritaire. Voir NFPA 70E.
PAGE 10
Relais de contrôle de charge WiserMC Caractéristiques et indications des DÉL S1B14484 Rév. 02, 03/2013 Pour obtenir la meilleure performance de radiofréquence (RF), monter le relais sur une surface non métallique ou avec le haut du relais à 39 mm (1,5 po) ou davantage au-dessus dune surface métallique. Utiliser des vis (non fournies) appropriées pour la surface de montage. Ne pas serrer les vis à l'excès.
PAGE 11
Relais de contrôle de charge WiserMC Joindre un réseau ZigBee® S1B14484 Rév. 02, 03/2013 Tableau 1 : Indications d’état des DÉL État des DÉL Taux Indication d’état • 100 % allumée • La charge est activée. Allumée pendant 1/10 seconde toutes les secondes • • La charge est désactivée. Le délestage de charge est en cours.
PAGE 12
Relais de contrôle de charge WiserMC Directives d’utilisation S1B14484 Rév.