SCHLAGE SENSE™ Smart Deadbolt User Guide Setup Code Setup Code Setup Code Place Label Here Poner la etiqueta aquí Placer l’autocollant ici Default Codes Códigos de predeterminado Codes du défaut Place Label Here Poner la etiqueta aquí Placer l’autocollant ici PLEASE KEEP THIS GUIDE CONSERVE ESTA GUÍA You will need these codes to operate your lock! ¡Necesitará estos códigos para operar la cerradura! VEUILLEZ CONSERVERCE GUIDE Vous aurez besoin de ces codes pour faire fonctionner la serrure!
ENGLISH Schlage Sense™ User Guide Contents Lock Setup....................................3 Lock Parts......................................4 Setup Code and Default Access Codes...................................................... 4 Locking and Unlocking................5 Cleaning the Lock.........................6 Replacing the Batteries...............6 Manual Programming Guide....... 7 Programming Descriptions............7 Manual Programming Guide...... 8 Programming Procedures.............8 My Codes...
REGISTER YOUR LOCK Document your purchase and register your warranty at Schlage.
LOCK PARTS DOOR INTERIOR Alarm DOOR EXTERIOR Touchscreen Outside Schlage Button Alarm Speaker Touchscreen Inside Schlage Button Cylinder Thumbturn ENGLISH Bolt Inside Schlage Button •• Located on the inside of the door. •• Used to silence the alarm. •• Does not lock or unlock the door. Thumbturn •• Used to lock and unlock manually from the inside. Outside Schlage Button •• Located on the outside of the door. •• Locks the deadbolt with 1-Touch Locking.
LOCKING AND UNLOCKING You can lock and unlock your door with a simple press using the Schlage Sense app! FROM THE OUTSIDE To Lock To Unlock 2. The lock will lock. The green check mark will light once. 2. Enter a valid access code. LL If the bolt cannot fully extend, the red X will light and a tone will sound. The door may remain unlocked! LL If the red error X lights, the access code was not valid. 1. Press the Schlage Button. 1. Press the Schlage Button. ENGLISH 3.
CLEANING THE LOCK In order to properly clean the touchscreen from build-up of dirt, oils, or other contaminates; you should use a mild dish soap with warm water and follow the general rules below: •• Do rinse the touchscreen with warm water prior to cleaning process. •• Do follow the application of soap with a damp, lukewarm cloth •• Don’t use abrasives, high alkaline cleaners, or gasoline •• Don’t leave cleaners on touchscreen for long periods, wash immediately.
MANUAL PROGRAMMING GUIDE Use the app to easily program your lock! NOTE: Existing access codes will be deleted when you configure your lock with the app! Schlage recommends using the Schlage Sense mobile app to program your lock. If you don’t have the Schlage Sense app, you can use the manual programming instructions below.
MANUAL PROGRAMMING GUIDE »» Programming Procedures If you make a mistake during programming, press the outside Schlage button to leave Programming mode and start over. »»Programming mode will automatically time out after 30 seconds of inactivity. PROGRAMMING CODE Write your programming code here for easy access. ENGLISH WARNING Manual programming functions are NOT available after pairing using the mobile app! You must perform a Factory Default Reset to program your lock manually.
ENABLE/DISABLE 1-TOUCH LOCKING Press Press Enter Programming Code 7 Programming indicator light solid 2 blinks + 2 beeps CHANGE ACCESS CODE LENGTH Press Enter Programming Code Enter Desired Access Code Length 8 Programming indicator light solid Enter Same Desired Access Code Length Success! 2 blinks + 2 beeps WARNING: Changing the access code length will delete all existing access codes! ENABLE/DISABLE AUTO-LOCK Press Enter Programming Code Programming indicator light solid Press 9 2 blinks
MY CODES Use the Schlage Sense app to record and keep track of your access codes! If you are not using the Schlage Sense app, use these tables to record programming and access codes that you program into the lock. »» ENGLISH Use a pencil to enter the codes in the boxes so you can easily change them later. •• The Programming Code can be any combination of six numbers entered into the keypad to put the lock in Programming Mode.
PROGRAMMING CODE NAME EXAMPLE: JOHN SMITH ACCESS CODE 1 2 3 4 ENGLISH 11
TROUBLESHOOTING Problem Sounds Lights Solution I forgot my Programming Code.* — — Check the front of this guide or the back of the Alarm Assembly for default Programming Code. ENGLISH If needed, restore lock to factory settings. See Factory Default Reset on page 14. I need to delete an access code that I don’t remember.* — — Delete all access codes. Then add all needed access codes back into the lock. See Delete ALL Access Codes on page 8. Cannot add a new access code.
Problem Sounds Lights Solution Backlighting does not come on when Outside Schlage button is pressed and access code cannot be entered. — — Batteries are completely dead and no electronic operations are possible. See Replacing the Batteries on page 6. The battery tray is not connected. After entering an access code to unlock the lock, the yellow dot is flashing and there is a delay before unlock. Several beeps Outside yellow dot flashing Inside Schlage Button is flashing but no alarm is sounding.
FACTORY DEFAULT RESET When should you perform a Factory Default Reset? •• If you want to move the lock to a different door, you need to restore default settings, move the lock to the new door, and then set up the lock again. •• If you have forgotten your Programming Code, you can restore the default codes. •• If you have set up your lock using the mobile app, and would like to force the lock to unpair from all mobile devices, erase all codes, and restore the factory default settings and default codes.
WARRANTY Lifetime Limited Mechanical and Finish Warranty and 3-Year Limited Electronics Warranty Subject to the terms and conditions of the warranty, Schlage extends a lifetime limited mechanical and finish warranty and a three-year limited electronics warranty to the original consumer user (“Original User”) of our Schlage brand product (“Product”) against defects in material and workmanship, as long as the Original User occupies the residential premises upon which the Product was originally installed.
If you have questions about any part of installation or programming, don’t return your Schlage Sense™ to the store. Our Schlage Customer Service representatives are ready to help. Toll-free: 888-805-9837 answers.schlage.com Sans frais : 888-805-9837 Si tiene dudas acerca de cualquier parte de la instalación o programación, no devuelva su Schlage Sense a la tienda. Nuestros representantes del Departamento de Servicio de Asistencia al Cliente de Schlage están listos para ayudarlo.
