Instructions / Assembly

ManualsBrandsSchaefer ManualsCeiling Fans24 in. Black Oscillating Wall Mountable Ceiling Fan

Oscillating Circulation

Fan Operators Manual

IMPORTANT: READ AND SAVE THESE INSTRUCTIONS

Read all instructions carefully before attempting to assemble, install, operate or service the

product described. Failure to comply with instructions could result in personal injury and/or

property damage.

Using this product for any other purpose than it was intended, or not within the operating

speciﬁcations in this manual will void the warranty and may cause damage to the fan or serious

injury to personnel.

WARNING - TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK:

• Do not expose fan to water or rain.

• Do not use this fan with any speed control device.

• The power source must conform to the electrical requirements of the fan.

• The power cord has a 3-prong grounded plug that must be plugged into a GFCI (Ground Fault

Circuit Interrupter) protected circuit.

• Do not alter the plug to remove the grounding prong and never use a 2-prong adapter.

• Replace damaged or worn power cords immediately.

• Where possible, avoid using extension cords. If one must be used, the cord must be UL listed,

be the proper size (Amp rating), and have 3-prong grounded connections.

GENERAL SAFETY INFORMATION:

• Before operating this fan, check for worn, damaged, or missing parts and replace or repair as

needed.

• To avoid risk of ﬁre, electric shock or personal injury, disconnect from power source before

servicing.

• This fan is intended for general use only. Do not use near hazardous or explosive materials or

vapors.

• Never insert ﬁngers or any other objects through the guards when fan is in operation.

• Never operate fan without guards in place.

• Unplug the fan before moving from one location to another.

• All Warning and Caution labels must be kept in good condition and be replaced if not clearly

readable.

• Carefully read all safety messages in this manual and on your equipment safety labels. Follow

recommended precautions and safe operating practices.

SCVA-409

Summary of content (8 pages)

PAGE 1
Oscillating Circulation Fan Operators Manual IMPORTANT: READ AND SAVE THESE INSTRUCTIONS Read all instructions carefully before attempting to assemble, install, operate or service the product described. Failure to comply with instructions could result in personal injury and/or property damage. Using this product for any other purpose than it was intended, or not within the operating specifications in this manual will void the warranty and may cause damage to the fan or serious injury to personnel.
PAGE 2
KEEP THIS MANUAL IN A CLEAN, DRY PLACE FOR FUTURE REFERENCE. All information, illustrations and specifications in this manual are based on the latest product information available at the time of printing. Product specifications subject to change. We reserve the right to make changes at any time without notice. If you need replacement parts, please contact your dealer. Take special care when ordering replacement blades and motors to ensure you get the proper configuration for your fan.
PAGE 3
INSTALLING THE FAN TO A PEDESTAL ASSEMBLY Use the supplied hardware that came with your fan to attach the fan. 1. Position the fan assembly with the Oscillator Base at either side of the mounting tab. 2. Install the 3/8" bolt through the center hole of the Oscillator Base and fasten with 3/8" narrow washers and nylock nut. 3. Install the 1/4" bolt through the slot feature and fasten with 1/4" narrow washers and nylock nut. Adjust the fan to the desired angle* and securely tighten all mounting hardware.
PAGE 4
CLEANING AND MAINTENANCE ! • • • • • Disconnect power before cleaning or maintaining your fan in order to prevent serious injury or death. Excessive dust and debris may cause overheating and reduced fan performance. Keep guards, motor and blades clean by vacuuming or wiping with a damp cloth. Do not use harsh chemicals or cleaners to clean any part of the fan. Pressure washing the unit will void the warranty. Sealed motor bearings are pre-lubricated and do not require servicing.
PAGE 5
Manual del operador del ventilador de circulación oscilante IMPORTANTE: LEA Y CONSERVE ESTAS INSTRUCCIONES Lea detenidamente todas las instrucciones antes de intentar armar, instalar, operar o dar servicio al producto descrito. De no cumplir con estas instrucciones podría ocasionar lesiones personales y/o daños materiales.
PAGE 6
CONSERVE ESTE MANUAL EN UN LUGAR LIMPIO Y SECO PARA REFERENCIA FUTURA. Toda la información, ilustraciones y especificaciones de este manual se basan en la información de producto más reciente, disponible al momento de ir a la imprenta. Las especificaciones del producto están sujetas a cambios. Nos reservamos el derecho de realizar cambios en cualquier momento sin previo aviso. Si necesita piezas de repuesto, comuníquese con su distribuidor.
PAGE 7
INSTALACIÓN DEL VENTILADOR EN UN CONJUNTO DE PEDESTAL Use los herrajes suministrados que venían con su ventilador para fijar el ventilador. 1. Coloque el conjunto del ventilador con la base oscilante en cualquiera de los lados de la pestaña de montaje. 2. Instale el perno de 3/8 pulg. a través del orificio central de la base oscilante y sujete con arandelas angostas de 3/8 pulg. y la tuerca Nylock. 3. Instale el perno de 1/4 pulg. a través de la ranura y sujete con arandelas delgadas de 1/4 pulg.
PAGE 8
LIMPIEZA Y MANTENIMIENTO ! • • • • • Desconecte la electricidad antes de limpiar o mantener su ventilador, con el fin de prevenir lesiones graves o la muerte. El exceso de polvo y residuos puede ocasionar sobrecalentamiento y reducir el desempeño del ventilador. Mantenga los protectores, el motor y las aspas limpias aspirando o limpiando con un paño húmedo. No use productos químicos o limpiadores fuertes para limpiar cualquier parte del ventilador. El lavado a presión de la unidad anulará la garantía.