sauder.com Store behind closed doors. Storage Cabinet Cannery Bridge Collection | Model 416082 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-24 Français pg 25-28 Español pg 29-32 Lot # 527583 03/25/19 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification 2-3 Hardware Identification Assembly Steps Assembly Tools Required No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-24 Hammer Français 25-28 Español 29-32 Safety 33-34 Warranty Not actual size Skip the power trip. This time. 35 Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other.
Part Identification K D2 A I S H H U F2 C H H G L U B H O H R G R U N2 E2 P T U T M J O www.sauder.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å To begin assembly, push ten SAUDER TWIST-LOCK® FASTENERS (10F) into the large holes in the ENDS (A and B), UPRIGHT (C), and BOTTOM (E2). Do not tighten the TWIST-LOCK® FASTENERS in this step. 10F E2 10F C B A www.sauder.
Step 2 å Push twenty-four HIDDEN CAMS (1F) into the ENDS (A and B), SKIRTS (M, N2, and O), and MOLDINGS (P and S). Arrow (24 used) 1F Arrow 1F B A Arrow 1F O N2 O Arrow P M S Hole Arrow The arrow in the HIDDEN CAM must point toward the hole in the edge of the board. 1F Page 6 416082 www.sauder.
Step 3 å å Turn twenty-four CAM SCREWS (8F) into the LEGS (I, J, K, and L). NOTE: Be sure to use the exact holes in the LEGS as shown. (24 used) 8F 8F L K J I 8F 8F www.sauder.
Step 4 å å Flip the ENDS (A and B) over. å Slide the END MOLDINGS (U) onto the ENDS (A and B). Line up the grooves in the MOLDINGS over the heads of the SCREWS in the ENDS. Remember: Righty tighty. Lefty loosey. Turn eight BLACK 9/16" FLAT HEAD SCREWS (32S) into the ENDS (A and B) until the shoulders of the SCREWS rest on the surfaces of the ENDS. U Center the MOLDINGS on the ENDS. B A U e fac t Sur ithou DEN w ID S H AM C U e fac t Sur ithou DEN w ID S H AM C Center the MOLDINGS on the ENDS.
Step 5 å First, fill the holes in the LEG (I) 1/4 to 1/2 full with GLUE (54M). Then, insert two WOOD DOWELS (15F) into the holes. Wipe away the excess GLUE. å å Now, fill the hole in the END (A) 1/4 to 1/2 full with GLUE. å å å NOTE: Be sure the WOOD DOWEL in the LEG inserts into the hole in the END. å NOTE: Be sure the WOOD DOWEL in the LEG inserts into the hole in the SIDE SKIRT. å Last, fill the hole in the short edge of the SIDE SKIRT (O). Push a WOOD DOWEL (15F) into the hole.
Step 6 å å First, fill the hole in the LEG (K) 1/4 to 1/2 full with GLUE (54M). å NOTE: Be sure the WOOD DOWEL in the SIDE SKIRT inserts into the hole in the LEG. Wipe away the excess GLUE. ! Caution Inspect the parts thoroughly before assembling. Disassembly of glued parts is extremely difficult. Fasten the LEG (K) to the END (A) and SIDE SKIRT (O). Tighten the HIDDEN CAM and use five BLACK 2-3/4" FLAT HEAD SCREWS (100S). Fill the holes 1/4 to 1/2 full with GLUE.
Step 7 å First, fill the holes in the LEG (J) 1/4 to 1/2 full with GLUE (54M). Then, insert two WOOD DOWELS (15F) into the holes. Wipe away the excess GLUE. å å Now, fill the hole in the END (B) 1/4 to 1/2 full with GLUE. å å å NOTE: Be sure the WOOD DOWEL in the LEG inserts into the hole in the END. å NOTE: Be sure the WOOD DOWEL in the LEG inserts into the hole in the SIDE SKIRT. å Last, fill the hole in the short edge of the SIDE SKIRT (O). Push a WOOD DOWEL (15F) into the hole.
Step 8 å å First, fill the hole in the LEG (L) 1/4 to 1/2 full with GLUE (54M). å NOTE: Be sure the WOOD DOWEL in the SIDE SKIRT inserts into the hole in the LEG. Wipe away the excess GLUE. ! Caution Inspect the parts thoroughly before assembling. Disassembly of glued parts is extremely difficult. Fasten the LEG (L) to the END (B) and SIDE SKIRT (O). Tighten the HIDDEN CAM and use five BLACK 2-3/4" FLAT HEAD SCREWS (100S). Fill the holes 1/4 to 1/2 full with GLUE.
Step 9 å Fasten the BRACES (T) to the BOTTOM (E2). Use four BROWN 1-1/2" FLAT HEAD SCREWS (14S). å Fasten the BOTTOM (E2) to the LEFT END (B). Tighten two TWIST-LOCK® FASTENERS. Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. 14S BROWN 1-1/2" FLAT HEAD SCREW (4 used in this step) T T How to use the SAUDER TWIST-LOCK® FASTENER with CK® e c fa -LO RS Sur WIST TENE T AS F 1. Insert the dowel end of the FASTENER into the hole of the adjoining part.
Step 10 å Fasten the UPRIGHT (C) to the BOTTOM (E2). Use two BLACK 1-15/16" FLAT HEAD SCREWS (113S). Don't worry. It isn't Rome. This can be built in a day. Finished edge C Sur TW face w FASIST-L ithou TEN OCK t ER ® S E2 113S BLACK 1-15/16" FLAT HEAD SCREW (2 used in this step) Page 14 416082 www.sauder.
Step 11 å å å Fasten two METAL BRACKETS (4G) to the BACK SKIRT (N2). Use two BLACK 9/16" LARGE HEAD SCREWS (1S). å Now, fill the hole in the LEFT REAR LEG (L) 1/4 to 1/2 full with GLUE. Then, insert the WOOD DOWEL in the BACK SKIRT into this hole. Wipe away the excess GLUE. å NOTE: Be sure the CAM SCREWS in the LEG insert into the holes in the BACK SKIRT. Tighten these two HIDDEN CAMS at this time. å Fasten the BACK SKIRT (N2) to the BOTTOM (E2).
Step 12 å Fasten four METAL BRACKETS (4G) to the BOTTOM MOLDING (P) and TOP MOLDING (S). Use four BLACK 9/16" LARGE HEAD SCREWS (1S). å Fasten the BOTTOM MOLDING (P) and TOP MOLDING (S) to the LEFT FRONT LEG (J) on the LEFT END (B). Tighten two HIDDEN CAMS. å Fasten the BOTTOM MOLDING (P) to the BOTTOM (E2). Use two BLACK 9/16" LARGE HEAD SCREWS (1S) through the METAL BRACKETS on the BOTTOM MOLDING and into the BOTTOM.
Step 13 å First, fill the holes in the FRONT SKIRT (M) 1/4 to 1/2 full with GLUE (54M). Then, insert the WOOD DOWELS (15F) into the holes. Wipe away the excess GLUE. å å å å å å NOTE: Be sure to use the exact holes shown. å NOTE: Be sure the WOOD DOWELS in the SKIRTS and BOTTOM MOLDING insert into the holes in the LEGS. Now, fill the hole in the LEFT FRONT LEG (J) 1/4 to 1/2 full with GLUE. Fasten the FRONT SKIRT (M) to the LEFT FRONT LEG (J). Tighten the HIDDEN CAM.
Step 14 å Open the FURNITURE TIPPING RESTRAINT KIT (97) and fasten the SAFETY STRAP to the TOP (D2). Use the provided BLACK 9/16" LARGE HEAD SCREW. å å NOTE: Position the SAFETY STRAP exactly as shown. å Fasten the TOP MOLDING (S) to the TOP (D2). Use two BLACK 9/16" LARGE HEAD SCREWS (1S) through the METAL BRACKETS on the MOLDING and into the TOP. 97 Fasten the TOP (D2) to the ENDS (A and B) and UPRIGHT (C). Tighten six TWIST-LOCK® FASTENERS.
Step 15 å å å Carefully turn your unit over onto its front edges. å å Fasten the BACK (F2) to your unit using the NAILS (1N). å NOTE: Perforations have been provided for access through the BACK. Carefully cut out the holes needed. Unfold the BACK (F2) and lay it over your unit. Hey! It's starting to look like something! Make equal margins along the two short edges and along the two long edges of the BACK (F2). Push on opposite corners of your unit if needed to make it "square".
Step 16 å Fasten the DOOR MOLDINGS (R) to the DOORS (G). Use eight BROWN 1" FLAT HEAD SCREWS (12S). å Fasten three HINGES (14H) to each DOOR (G). Use twelve BLACK 1/2" FLAT HEAD SCREWS (11S). 12S BROWN 1" FLAT HEAD SCREW (8 used for the DOOR MOLDINGS) ith e w oles c a f Sur ore h m G ith e w oles c a f Sur ore h m G R R 11S BLACK 1/2" FLAT HEAD SCREW (12 used for the HINGES) ith e w oles c a f Sur ore h m 14H G withes e c fa ol Sur ore h m G 14H Page 20 416082 www.sauder.
Step 17 å å Carefully stand your unit upright. å Fasten a DOOR (G) to the RIGHT END (A) as shown in the lower diagram. Use the screws in the HINGES. You should start each SCREW a few turns before completely tightening any of them. å å Fasten a KNOB (95K) to the DOOR (G). Use a GRAY 1-3/8" MACHINE SCREW (39S). å å Repeat this step for the other DOOR (G). Before fastening the DOOR to your unit, be sure the mounting screw is against the stops as shown in the right diagram.
Step 18 å å å Refer to the enlarged diagram to identify the parts on the HINGES. å To adjust the DOORS up and down (vertical), loosen both vertical adjustment screws. Move the DOORS up or down to the desired location. Tighten the screws after making adjustments. å To adjust the DOORS in or out (depth), loosen the mounting screw one turn and move the DOORS in or out, as needed. Tighten the mounting screw after making adjustments. The DOORS may need some adjustments.
Step 19 å å Position your unit in its final location. We recommend using the SAFETY STRAP for added stability. å INSTALLATION INSTRUCTIONS: 1. Insert the SAFETY DRYWALL ANCHOR through the WASHER and the end of the SAFETY STRAP. 2. Using a Phillips screwdriver or a hand drill, press the screw slightly onto the drywall. 3. Apply pressure; turn the screw until a pilot hole is made and the nylon sheath slips through. 4. Turn the screw until it is flush against the wall and you feel a firm resistance. 5.
Step 20 å Push the RUBBER SLEEVES (2R) over the METAL PINS (1R). Insert the METAL PINS into the hole locations of your choice in the ENDS (A and B) and UPRIGHT (C). Set the ADJUSTABLE SHELVES (H) onto the METAL PINS. å å å Using your hammer, gently tap a CAM COVER (13P) onto each visible HIDDEN CAM. NOTE: Please read the back pages of the instruction booklet for important safety information. This completes assembly. Clean with a damp cloth. Wipe dry.
Modèle 416082 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 6 Ne pas serrer les FIXATIONS TWIST-LOCK® à cette étape. Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Pour commencer l'assemblage, enfoncer dix FIXATIONS TWIST-LOCK® SAUDER (10F) dans les gros trous dans les EXTRÉMITÉS (A et B), le MONTANT (C) et le DESSOUS (E2). Attention: Examiner bien les pièces avant d'assembler. Il est difficile de séparer des pièces une fois encollées.
ÉTAPE 9 ÉTAPE 12 Fixer les ENTRETOISES (T) au DESSOUS (E2). Utiliser quatre VIS TÊTE PLATE 38 mm MARRON (14S). Fixer quatre CONSOLES EN MÉTAL (4G) à la MOULURE DE DESSOUS (P) et à la MOULURE DE DESSUS (S). Utiliser quatre VIS TÊTE LARGE 14 mm NOIRES (1S). Attention: Ne pas relever l'élément dans sa position verticale avant d'avoir fixé l’ARRIÈRE. L'élément risque de s'effondrer. Fixer le DESSOUS (E2) à l'EXTRÉMITÉ GAUCHE (B). Serrer deux FIXATIONS TWIST-LOCK®.
ÉTAPE 15 ÉTAPE 18 (SUITE) Attention: Ne pas relever l'élément dans sa position verticale avant d'avoir fixé l’ARRIÈRE. L'élément risque de s'effondrer. Avec précaution, retourner l'élément sur ses chants avant. Déplier l'ARRIÈRE (F2) et le placer sur l'élément. Veiller à avoir des marges égales le long des deux chants courts et deux chants longs de l'ARRIÈRE (F2). Si besoin est, enfoncer sur les coins opposés de l'élément pour s'assurer d'être « d'équerre ».
Modelo 416082 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 6 No apriete los SUJETADORES TWIST-LOCK® en este paso. Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Para comenzar el ensamblaje, empuje diez SUJETADORES TWIST-LOCK® SAUDER (10F) dentro de los agujeros grandes de los EXTREMOS (A y B), del PARAL (C) y del FONDO (E2). Precaución: Revise las partes cuidadosamente antes de ensamblar. La separación de las piezas ya pegadas es muy difícil.
PASO 9 PASO 12 Fije las BISAGRAS (T) al FONDO (E2). Utilice cuatro TORNILLOS MARRONES DE CABEZA PERDIDA de 38 mm (14S). Fije cuatro SOPORTES DE METAL (4G) a la MOLDURA DE FONDO (P) y a la MOLDURA DE PANEL SUPERIOR (S). Utilice cuatro TORNILLOS NEGROS DE CABEZA GRANDE de 14 mm (1S). Precaución: No coloque la unidad en posición vertical hasta que se fije el DORSO. La unidad podría caerse. Fije el FONDO (E2) al EXTREMO IZQUIERDO (B). Apriete dos SUJETADORES TWIST-LOCK®.
PASO 15 Precaución: No coloque la unidad en posición vertical hasta que se fije el DORSO. La unidad podría caerse. Cuidadosamente voltee la unidad para que repose sobre los bordes delanteros. Desdoble el DORSO (F2) y colóquelo sobre la unidad. Deje márgenes iguales a lo largo de los dos bordes cortos y los dos bordes largos del DORSO (F2). Empuje sobre las esquinas opuestas de la unidad si es requerido para hacerla "cuadrada." Fije el DORSO (F2) a la unidad utilizando los CLAVOS (1N).
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following safety information. Death or serious injury may occur when children climb on furniture. A remote control, toys or other items placed on the furniture may encourage a child to climb on the furniture which could cause it to tip-over and result in serious injury or death. NEVER allow children to climb on furniture.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Lea cuidadosamente la siguiente información de seguridad. Pueden suceder lesiones graves o la muerte cuando los niños se suben en los muebles. Un control remoto, juguetes u otros artículos colocados en los muebles pueden alentar a un niño a subirse en el mueble, lo cual podría causar que se derribe y resultaría en lesiones graves o la muerte.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
