sauder.com Great for all those books you’ll never read. Tall Bookcase Barrister Lane Collection | 414725 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-18 Hammer Français 19-21 Español 22-24 Safety 25-26 Warranty Page 2 Not actual size Skip the power trip. This time. 27 414725 www.sauder.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. CAM DOWEL - 24 1F HIDDEN CAM - 32 2F 1G 4G METAL BRACKET - 8 SAFETY BRACKET - 1 36P CAM COVER - 4 CAM SCREW - 8 31G CORNER BRACKET - 2 38M CARD SHEET - 1 35M CARD HOLDER - 8 Page 4 8F 1N 1R NAIL - 77 METAL PIN - 28 1S BLACK 9/16" LARGE HEAD SCREW - 29 2S 7S BLACK 1-1/4" FLAT HEAD SCREW - 4 97S SILVER 3/8" MACHINE SCREW - 16 414725 BLACK 1-7/8" FLAT HEAD SCREW - 5 www.sauder.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å Push eight HIDDEN CAMS (1F) into the ENDS (A and B) and TOP (D). Arrow (8 used) 1F D B A Arrow Arrow 1F Hole The arrow in the HIDDEN CAM must point toward the hole in the edge of the board. www.sauder.
Step 2 å Push twenty-four HIDDEN CAMS (1F) into the BOTTOM (E) and SHELVES (F and G). Then, insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM. Do not tighten the HIDDEN CAMS in this step. 2F Arrow (24 used) 1F F G F G G G G G E Arrow Arrow 1F 2F Insert the metal end of the CAM DOWEL into the HIDDEN CAM. Page 6 414725 www.sauder.
Step 3 å Turn eight CAM SCREWS (8F) into the MOLDINGS (N and O). Remember: Righty tighty. Lefty loosey. (8 used) 8F N 8F www.sauder.
Step 4 å Fasten the MOLDINGS (N and O) to the ENDS (A and B). Tighten four HIDDEN CAMS. 1 2 Finished edge Surface with CAM DOWELS A Angled edge S wi urfa H th ce CA IDD M EN S Finished edge S wi urfa H th ce CA IDD M EN S B O N Angled edge Page 8 414725 www.sauder.
Step 5 å Fasten the UPRIGHT (C) to the TOP (D). Use two BLACK 1-7/8" FLAT HEAD SCREWS (2S). Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. This large hole must be positioned here. Finished edge These holes must be here. C Sur HIDface w DEN ith CA MS D 2S BLACK 1-7/8" FLAT HEAD SCREW (2 used in this step) www.sauder.
Step 6 å å å Insert a METAL PIN (1R) into each SHELF (F). Fasten the SHELVES (F) to the UPRIGHT (C). Tighten two HIDDEN CAMS. NOTE: Be sure the METAL PINS (1R) in the SHELVES (F) insert into the holes in the UPRIGHT (C). Edge with HIDDEN CAMS 1R F withMS e c fa A Sur DEN C HID C Edge with HIDDEN CAMS F ith e w AMS c a f Sur DEN C D I H 1R Caution Risk of damage or injury. HIDDEN CAMS must be completely tightened. HIDDEN CAMS that are not completely tightened may loosen, and parts may separate.
Step 7 å å Insert two METAL PINS (1R) into each PINNED SHELF (G). Insert the METAL PINS (1R) in one end of the PINNED SHELVES (G) into the holes in the UPRIGHT (C). Edge with HIDDEN CAMS (12 used) 1R Edge with HIDDEN CAMS G ith e w AMS c a f Sur DEN C HID G ith e w AMS c a f Sur DEN C D HI G ith e w AMS c a f Sur DEN C D HI G C withMS e c fa A Sur DEN C HID G withMS e c fa A Sur DEN C HID G Edge with HIDDEN CAMS ith e w AMS c a f Sur DEN C D HI 1R www.sauder.
Step 8 å Fasten the BOTTOM (E) to the UPRIGHT (C). Use two BLACK 1-7/8" FLAT HEAD SCREWS (1S). These holes must be here. C ith e w AMS c a f Sur DEN C D HI E 2S BLACK 1-7/8" FLAT HEAD SCREW (2 used in this step) Page 12 414725 www.sauder.
Step 9 å å Insert fourteen METAL PINS (1R) into the SHELVES (F and G). å NOTE: Be sure the METAL PINS (1R) in the SHELVES (F and G) insert into the holes in the ENDS (A and B). å Fasten the BASES (J and K) to the ENDS (A and B). Use four BLACK 1-1/4" FLAT HEAD SCREWS (7S). Maximum 210 degrees Fasten the ENDS (A and B) to the TOP (D), BOTTOM (E), and SHELVES (F). Tighten ten HIDDEN CAMS.
Step 10 å Fasten seven METAL BRACKETS (4G) to the ENDS (A and B) and BOTTOM (E). Use seven BLACK 9/16" LARGE HEAD SCREWS (1S). å NOTE: Be sure the BRACKETS are even with the edges of the ENDS and BOTTOM. å Fasten the BASE (I) to the ENDS (A and B) and BOTTOM (E). Use seven BLACK 9/16" LARGE HEAD SCREWS (1S) through the METAL BRACKETS and into the BASE. 1S BLACK 9/16" LARGE HEAD SCREW (14 used in this step) A I E B 4G 4G (7 used) 4G Page 14 414725 www.sauder.
Step 11 å Fasten two CARD HOLDERS (35M) to a SHELF MOLDING (L). Use four SILVER 3/8" MACHINE SCREWS (97S). Repeat this step for the other CARD HOLDERS and SHELF MOLDINGS. å Fasten the SHELF MOLDINGS (L) to the SHELVES (F and G). Tighten sixteen HIDDEN CAMS. Open end (8 used) 35M 97S Unfinished surface L SILVER 3/8" MACHINE SCREW (16 used for the CARD HOLDERS) Open end L Open end G L G L G F L G G F G Maximum 210 degrees Arrow Minimum 190 degrees www.sauder.
Step 12 å Fasten two CORNER BRACKETS (31G) to the MOLDINGS (N and O) and TOP (D). Use eight BLACK 9/16" LARGE HEAD SCREWS (1S). å Fasten a METAL BRACKET (4G) to the TOP (D). Use a BLACK 9/16" LARGE HEAD SCREW (1S). å Fasten the FRONT MOLDING (M) to the TOP (D) and MOLDINGS (N and O). Use five BLACK 9/16" LARGE HEAD SCREWS (1S) through the METAL BRACKET (4G) and CORNER BRACKETS (31G) and into the FRONT MOLDING.
Step 13 å Carefully turn your unit over onto its front edges. Unfold the BACK (H) and lay it over your unit. å Make equal margins along all four edges of the BACK (H). Push on opposite corners of your unit if needed to make it "square". å å Fasten the BACK (H) to your unit using the NAILS (1N). Caution Do not stand the unit upright without the BACK fastened. The unit may collapse. NOTE: Be sure to tap NAILS into the holes that line up over the UPRIGHT (C) and SHELVES (F and G).
Step 14 å å Carefully stand your unit upright. å å å å Push a CAM COVER (36P) onto each visible HIDDEN CAM. We recommend using the SAFETY BRACKET (1G) for added stability. Use a BLACK 9/16" LARGE HEAD SCREW (1S) into the top of the unit and a BLACK 1-7/8" FLAT HEAD SCREW (2S) into a stud in your wall. Separate the CARDS on the CARD SHEET (38M) and insert into the CARD HOLDERS. NOTE: Please read the back pages of the instruction booklet for important safety information. This completes assembly.
414725 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 6 Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Insérer une GOUPILLE EN MÉTAL (1R) dans chaque TABLETTE (F). Enfoncer huit EXCENTRIQUES ESCAMOTABLES (1F) dans les EXTRÉMITÉS (A et B) et le DESSUS (D). ÉTAPE 2 Ne pas serrer les CAMES ESCAMOTABLES dans cette étape. Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Fixer les TABLETTES (F) au MONTANT (C).
ÉTAPE 10 ÉTAPE 13 Fixer sept CONSOLES EN MÉTAL (4G) aux EXTRÉMITÉS (A et B) et au DESSOUS (E). Utiliser sept VIS TÊTE LARGE 14 mm NOIRES (1S). Attention: Ne pas relever l'élément dans sa position verticale avant d'avoir fixé l’ARRIÈRE. L'élément risque de s'effondrer. REMARQUE : S'assurer que les CONSOLES sont à fleur des chants des EXTRÉMITÉS et du DESSOUS. Avec précaution, retourner l'élément sur ses chants avant. Déplier l'ARRIÈRE (H) et le placer sur l'élément.
414725 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 6 Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Inserte una ESPIGA DE METAL (1R) dentro de cada ESTANTE (F). Empuje ocho EXCÉNTRICOS ESCONDIDOS (1F) dentro de los EXTREMOS (A y B) y el PANEL SUPERIOR (D). PASO 2 No apriete los EXCÉNTRICOS ESCONDIDOS en este paso. Empuje veinte y cuatro EXCÉNTRICOS ESCONDIDOS (1F) dentro del FONDO (E) y los ESTANTES (F y G).
PASO 10 PASO 13 Fije siete SOPORTES DE METAL (4G) a los EXTREMOS (A y B) y al FONDO (E). Utilice siete TORNILLOS NEGROS DE CABEZA GRANDE de 14 mm (1S). Precaución: No coloque la unidad en posición vertical hasta que se fije el DORSO. La unidad podría caerse. NOTA: Asegúrese que los SOPORTES estén nivelados con los bordes de los EXTREMOS y del FONDO. Fije la BASE (I) a los EXTREMOS (A y B) y al FONDO (E).
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded shelves. • Improper loading can cause the product to be top-heavy. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded shelves can break. • Never exceed the weight limits shown in the instructions.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Estantes sobrecargados. • Cargar el producto inadecuadamente puede causar la inestabilidad. • Riesgo de lesiones. • El mobiliario inestable puede volcarse. • Estantes sobrecargados pueden romper.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
