sauder.com Store behind closed doors. Storage Cabinet HomePlus Collection | Model 411572 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-523-3987. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-36 Français pg 37-40 Español pg 41-44 Lot # 367954 01/08/15 Purchased: __________________ Be sure to give us a ring before making any returns.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 2-3 No. 2 Phillips Screwdriver Tip Shown Actual Size 3-4 5-36 Hammer Français 37-40 Español 41-44 Safety 45-46 Warranty Not actual size Electric Drill with 1/4" bit 47 Tape Measure Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other.
Now you know our ABCs. Part Identification K E S G N P B H O J I A G D O N P L M O C G F R R Q Hardware Identification T FRONT FOOT - 2 www.sauder.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å You have the option to assemble the Storage Cabinet with the LARGE DOOR on the left or the LARGE DOOR on the right. å Follow steps 1-16 to assemble the LARGE DOOR on the left. LARGE DOOR ON LEFT LARGE DOOR ON RIGHT Scan this QR code or go to this address: http://qr.sauder.com/?ID= 1133 to watch a video for the large door on the left. å Follow steps 17-32 to assemble the LARGE DOOR on the right.
Step 2 å Fasten the LARGE END (B) to the TOP (E). Tighten two TWIST-LOCK® FASTENERS. å Fasten the LARGE SHELF (I) to the LARGE END (B). Tighten two TWIST-LOCK® FASTENERS. LARGE DOOR ON LEFT How to use the SAUDER TWIST-LOCK® FASTENER 1. Insert the dowel end of the FASTENER into the hole of the adjoining part. NOTE: The dowel end of the FASTENER must remain fully inserted in the hole of the adjoining part while locking the FASTENER. Caution Do not stand the unit upright without the BACK fastened.
Step 3 å NOTE: Stand the UPRIGHT (D) in place to be sure you are drilling through the correct holes in the TOP (E). å There are four pre-drilled holes in the top surface of the TOP (E). Finish drilling out two holes with your electric drill and 1/4" drill bit. å Fasten the UPRIGHT (D) to the TOP (E). Use two BLACK 1-7/8" FLAT HEAD SCREWS (MM). å Fasten the UPRIGHT (D) to the LARGE SHELF (I). Tighten two TWIST-LOCK® FASTENERS.
Step 4 å Fasten the TOP MOLDING (S) to the TOP (E). Tighten three TWIST-LOCK® FASTENERS. å Fasten the SMALL SHELF (J) to the UPRIGHT (D). Tighten two TWIST-LOCK® FASTENERS. LARGE DOOR ON LEFT Angled edge S E Finished edge D J Sur T W f a ce w IS it FAS T-LOCh T EN K® ER S Page 8 411572 www.sauder.
Step 5 å Fasten the SMALL END (A) to the TOP (E) and SMALL SHELF (J). Tighten four TWIST-LOCK® FASTENERS. LARGE DOOR ON LEFT E J ut itho ® w e fac CK Sur ST-LO RS I TW TENE FAS www.sauder.
Step 6 å Finish drilling out the pre-drilled hole with your electric drill and 1/4" drill bit to fasten the BOTTOM(F) to the LARGE END (B) and UPRIGHT (D). å Fasten the BOTTOM (F) to the ENDS (A and B) and UPRIGHT (D). Use six BLACK 1-7/8" FLAT HEAD SCREWS (MM). LARGE DOOR ON LEFT B Rounded edge D A Un fin ish ed su rfa ce F Drill through these pre-drilled holes. MM BLACK 1-7/8" FLAT HEAD SCREW (6 used in this step) Page 10 411572 www.sauder.
Step 7 å å Slide the FEET (T and U) into the notches in the SKIRTS (Q and R). å Fasten the SKIRTS (Q and R) to the BOTTOM (F). Use four BLACK 9/16" WAFER HEAD SCREWS (QQ) through the FEET and into the BOTTOM as shown in the lower diagram. LARGE DOOR ON LEFT Use a hammer to drive a PROPEL NUT (DD) into the holes in the FEET (T and U). Now, turn an ADJUSTABLE GLIDE (CC) into each PROPEL NUT as shown in the upper diagram. CC (4 used) T DD U R Q T This hole must be here.
Step 8 å Carefully turn your unit over onto its front edges. Unfold the BACK (K) and lay it over your unit. å Make equal margins along all four edges of the BACK (K). Push on opposite corners of your unit if needed to make it “square”. å å Fasten the BACK (K) to your unit using the NAILS (TT). å NOTE: Turn the adjustable ends of the ADJUSTABLE FEET completely in. Final adjustments will be made after the unit is standing upright. å LARGE DOOR ON LEFT Fasten the FOOT BASES (KK) to the BOTTOM (F).
Step 9 å Insert a METAL PIN (AA) into the holes in the DOOR END (C) and top short edge of the DOOR SHELVES (G). å Fasten the DOOR SHELVES (G) to the DOOR END (C). Tighten three TWIST-LOCK® FASTENERS. å Fasten the DOOR UPRIGHT (H) to the DOOR SHELVES (G). Tighten three TWIST-LOCK® FASTENERS. å NOTE: Be sure the PINS insert into the edges of the DOOR SHELVES and DOOR UPRIGHT before you tighten the TWIST-LOCK® FASTENERS.
Step 10 å Fasten the STRIKE PLATES (HH) to the SMALL DOOR (M). Use two BLACK 1/2" LARGE HEAD SCREWS (SS). å Fasten the PULL (X) to the SMALL DOOR (M). Use two SILVER 3/4" MACHINE SCREWS (OO). å Fasten the DOOR UPRIGHT (H) and DOOR END (C) to the SMALL DOOR (M). Tighten six TWIST-LOCK® FASTENERS. å Fasten the HINGES (LL) to the DOOR END (C). Use eight BLACK 9/16" LARGE HEAD SCREWS (RR).
Step 11 å å Carefully turn your unit over onto its BACK. å Fasten the HINGES (LL) to the SMALL END (A). Use eight BLACK 9/16" LARGE HEAD SCREWS (RR). å Push the DOOR STOPS (Z) into the holes in the top and bottom corners of the UPRIGHT (D). LARGE DOOR ON LEFT Place the SMALL DOOR assembly next to the SMALL END (A). Place packing material, books or magazines underneath the SMALL DOOR assembly for support while you fasten the HINGES (LL) to the SMALL END.
Step 12 å Fasten three SPRING HINGES (EE) to the LARGE DOOR (L). Use six BLACK 1/2" FLAT HEAD SCREWS (SS). LARGE DOOR ON LEFT SS BLACK 1/2" FLAT HEAD SCREW (2 used for the HINGES) EE L Page 16 411572 www.sauder.
Step 13 å å å å Carefully stand your unit upright. å Before fastening the DOOR to your unit, be sure the mounting screw is against the stops as shown in the left diagram. If it isn't, loosen the mounting screw to slide it against the stops. Then tighten the mounting screw. å Fasten the LARGE DOOR (L) to the LARGE END (B) as shown in the lower diagram. Use the screws in the HINGES. You should start each SCREW a few turns before completely tightening any of them.
Step 14 å Refer to the enlarged diagram to identify the parts on the HINGES. å The DOORS may need some adjustments. Follow the text below to make needed adjustments. å DOOR ADJUSTMENTS: To adjust the DOORS from side to side (horizontal), turn the adjusting screw in or out. å To adjust the DOORS up and down (vertical), loosen both vertical adjustment screws. Move the DOORS up or down to the desired location. Tighten the screws after making adjustments.
Step 15 å With a hammer, gently tap twelve SHELF SNAPS (II) into the holes in the ADJUSTABLE DOOR SHELVES (O). å Insert twelve METAL PINS (AA) into the hole locations of your choice in the DOOR END (C) and DOOR UPRIGHT (H). Set the DOOR SHELVES onto the METAL PINS and push down until each SHELF "snaps" into the SHELF SNAP (II). å Push the RUBBER SLEEVES (BB) over sixteen METAL PINS (AA). Insert the METAL PINS into the hole locations of your choice in the LARGE END (B) and UPRIGHT (D).
Step 16 å Fasten the SAFETY BRACKET (Y) for added stability. Use a BLACK 9/16” LARGE HEAD SCREW (RR) into the top of the unit and a BLACK 1-7/8” FLAT HEAD SCREW (MM) into a stud in your wall. å Push the HOLE PLUGS (FF and GG) into the visible holes, not including the adjustable shelf pin holes in the SMALL DOOR assembly and UPRIGHT (D). å NOTE: To raise a corner of the unit, turn the ADJUSTABLE GLIDE counter-clockwise. To lower a corner, turn the ADJUSTABLE GLIDE clockwise.
Step 17 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å To begin assembly, push a SAUDER TWIST-LOCK® FASTENER (V) into the large holes in the ENDS (A and B), DOOR END (C),TOP (E), DOOR SHELVES (G), LARGE SHELF (I), DOOR UPRIGHT (H), and SMALL SHELF (J). å NOTE: Do not tighten the TWIST-LOCK® FASTENERS at this time. LARGE DOOR ON RIGHT Do not tighten the TWIST-LOCK® FASTENERS in this step. V 27 used) A B www.sauder.
Step 18 å Fasten the LARGE END (B) to the TOP (E). Tighten two TWIST-LOCK® FASTENERS. å Fasten the LARGE SHELF (I) to the LARGE END (B). Tighten two TWIST-LOCK® FASTENERS. LARGE DOOR ON RIGHT How to use the SAUDER TWIST-LOCK® FASTENER 1. Insert the dowel end of the FASTENER into the hole of the adjoining part. NOTE: The dowel end of the FASTENER must remain fully inserted in the hole of the adjoining part while locking the FASTENER. 2.
Step 19 å NOTE: Stand the UPRIGHT (D) in place to be sure you are drilling through the correct holes in the TOP (E). å There are four pre-drilled holes in the top surface of the TOP (E). Finish drilling out two holes with your electric drill and 1/4" drill bit. å Fasten the UPRIGHT (D) to the TOP (E). Use two BLACK 1-7/8" FLAT HEAD SCREWS (MM). å Fasten the UPRIGHT (D) to the LARGE SHELF (I). Tighten two TWIST-LOCK® FASTENERS.
Step 20 å Fasten the TOP MOLDING (S) to the TOP (E). Tighten three TWIST-LOCK® FASTENERS. å Fasten the SMALL SHELF (J) to the UPRIGHT (D). Tighten two TWIST-LOCK® FASTENERS. LARGE DOOR ON RIGHT Angled edge S E Finished edge D J i th ce wCK® a f r Su T-LO S R IS T W T EN E S FA Page 24 411572 www.sauder.
Step 21 å Fasten the SMALL END (A) to the TOP (E) and SMALL SHELF (J). Tighten four TWIST-LOCK® FASTENERS. LARGE DOOR ON RIGHT E J Edge with TWIST-LOCK® FASTENERS www.sauder.
Step 22 å Finish drilling out the pre-drilled hole with your electric drill and 1/4" drill bit to fasten the BOTTOM(F) to the LARGE END (B) and UPRIGHT (D). å Fasten the BOTTOM (F) to the ENDS (A and B) and UPRIGHT (D). Use six BLACK 1-7/8" FLAT HEAD SCREWS (MM). LARGE DOOR ON RIGHT B Rounded edge D F A ed ish n fi Un face r su Drill through these pre-drilled holes. MM BLACK 1-7/8" FLAT HEAD SCREW (6 used in this step) Page 26 411572 www.sauder.
Step 23 å Slide the FEET (T and U) into the notches in the SKIRTS (Q and R). å Use a hammer to drive a PROPEL NUT (DD) into the holes in the FEET (T and U). Now, turn an ADJUSTABLE GLIDE (CC) into each PROPEL NUT as shown in the upper diagram. å Fasten the SKIRTS (Q and R) to the BOTTOM (F). Use four BLACK 9/16" WAFER HEAD SCREWS (QQ) through the FEET and into the BOTTOM as shown in the lower diagram. LARGE DOOR ON RIGHT CC (4 used) T (4 used) U DD R Q T This hole must be here.
Step 24 å Carefully turn your unit over onto its front edges. Unfold the BACK (K) and lay it over your unit. å Make equal margins along all four edges of the BACK (K). Push on opposite corners of your unit if needed to make it “square”. å å Fasten the BACK (K) to your unit using the NAILS (TT). å NOTE: Turn the adjustable ends of the ADJUSTABLE FEET completely in. Final adjustments will be made after the unit is standing upright. å Fasten the METAL BRACKET (W) to the BOTTOM (F) and FRONT SKIRT (Q).
Step 25 å Insert a METAL PIN (AA) into the holes in the DOOR END (C) and top short edge of the DOOR SHELVES (G). å Fasten the DOOR SHELVES (G) to the DOOR END (C). Tighten three TWIST-LOCK® FASTENERS. å Fasten the DOOR UPRIGHT (H) to the DOOR SHELVES (G). Tighten three TWIST-LOCK® FASTENERS. å NOTE: Be sure the PINS insert into the edges of the DOOR SHELVES and DOOR UPRIGHT before you tighten the TWIST-LOCK® FASTENERS.
Step 26 å Fasten the STRIKE PLATES (HH) to the SMALL DOOR (M). Use two BLACK 1/2" LARGE HEAD SCREWS (SS). å Fasten the PULL (X) to the SMALL DOOR (M). Use two SILVER 3/4" MACHINE SCREWS (OO). å Fasten the DOOR UPRIGHT (H) and DOOR END (C) to the SMALL DOOR (M). Tighten six TWIST-LOCK® FASTENERS. å Fasten the HINGES (LL) to the DOOR END (C). Use eight BLACK 9/16" LARGE HEAD SCREWS (RR).
Step 27 å å Carefully turn your unit over onto its BACK. å Fasten the HINGES (LL) to the SMALL END (A). Use eight BLACK 9/16" LARGE HEAD SCREWS (RR). å Push the DOOR STOPS (Z) into the holes in the top and bottom corners of the UPRIGHT (D). LARGE DOOR ON RIGHT Place the SMALL DOOR assembly next to the SMALL END (A). Place packing material, books or magazines underneath the SMALL DOOR assembly for support while you fasten the HINGES (LL) to the SMALL END.
Step 28 å Fasten three HINGES (EE) to the LARGE DOOR (L). Use six BLACK 1/2" FLAT HEAD SCREWS (SS). LARGE DOOR ON RIGHT SS BLACK 1/2" FLAT HEAD SCREW (2 used for the HINGES) EE L Page 32 411572 www.sauder.
Step 29 å å å å Carefully stand your unit upright. å Before fastening the DOOR to your unit, be sure the mounting screw is against the stops as shown in the right diagram. If it isn't, loosen the mounting screw to slide it against the stops. Then tighten the mounting screw. å Fasten the LARGE DOOR (L) to the LARGE END (B) as shown in the lower diagram. Use the screws in the HINGES. You should start each SCREW a few turns before completely tightening any of them.
Step 30 å Refer to the enlarged diagram to identify the parts on the HINGES. å The DOORS may need some adjustments. Follow the text below to make needed adjustments. å DOOR ADJUSTMENTS: To adjust the DOORS from side to side (horizontal), turn the adjusting screw in or out. å To adjust the DOORS up and down (vertical), loosen both vertical adjustment screws. Move the DOORS up or down to the desired location. Tighten the screws after making adjustments.
Step 31 å With a hammer, gently tap twelve SHELF SNAPS (II) into the holes in the ADJUSTABLE DOOR SHELVES (O). å Insert twelve METAL PINS (AA) into the hole locations of your choice in the DOOR END (C) and DOOR UPRIGHT (H). Set the DOOR SHELVES onto the METAL PINS and push down until each SHELF "snaps" into the SHELF SNAP (II). å Push the RUBBER SLEEVES (BB) over sixteen METAL PINS (AA). Insert the METAL PINS into the hole locations of your choice in the LARGE END (B) and UPRIGHT (D).
Step 32 å Fasten the SAFETY BRACKET (Y) for added stability. Use a BLACK 9/16” LARGE HEAD SCREW (RR) into the top of the unit and a BLACK 1-7/8” FLAT HEAD SCREW (MM) into a stud in your wall. å Push the HOLE PLUGS (FF and GG) into the visible holes, not including the adjustable shelf pin holes in the SMALL DOOR assembly and UPRIGHT (D). å NOTE: To raise a corner of the unit, turn the ADJUSTABLE GLIDE counter-clockwise. To lower a corner, turn the ADJUSTABLE GLIDE clockwise.
Modèle 411572 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
ÉTAPE 1 ÉTAPE 7 (SUITE) Vous avez l’option d’assembler le meuble de rangement avec la GRANDE PORTE sur la gauche ou la GRANDE PORTE sur la droite. Fixer les PLINTHES (Q et R) au DESSOUS (F). Utiliser quatre VIS NOIRES TÊTE MINCE 1 4 mm (QQ) à travers les PIEDS et dans le DESSOUS comme l'indique le schéma du bas. Suivre les étapes 1 à 16 pour assembler la GRANDE PORTE sur la gauche.
ÉTAPE 13 ÉTAPE 18 Relever, avec précaution, l'élément dans sa position verticale. Attention: Ne pas relever l'élément dans sa position verticale avant d'avoir fixé l’ARRIÈRE. L'élément risque de s'effondrer. Faire tourner le PIED (JJ) pour ajuster. Le PIED ne doit pas dépasser le chant inférieur des PLINTHE LATÉRALE (R). Avant de fixer la PORTE à l’unité, s’assurer que la vis de montage se trouve contre les butées comme l’indique le schéma de gauche.
ÉTAPE 24 ÉTAPE 29 Attention Ne pas relever l'élément dans sa position verticale avant d'avoir fixé l’ARRIÈRE. L'élément risque de s'effondrer. Relever, avec précaution, l'élément dans sa position verticale. Avec précaution, retourner l'élément sur ses chants avant. Déplier l'ARRIÈRE (K) et le placer sur l'élément. Veiller à avoir des marges égales le long des quatre chants de l'ARRIÈRE (K). Si besoin est, enfoncer sur les coins opposés de l'élément pour s'assurer d'être « d'équerre ».
Modelo 411572 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PASO 1 PASO 7 Usted tiene la opción de montar el Gabinete para almacenaje con la PUERTA GRANDE a la izquierda o la PUERTA GRANDE en el lado derecho. Deslice las PATAS (T y U) dentro de las muescas de los FALDONES (Q y R). Siga los pasos 1 a 16 para fijar la PUERTA GRANDE al lado izquierdo. Siga los pasos 17 a 32 para fijar la PUERTA GRANDE al lado derecho. Utilice un martillo para golpear una TUERCA (DD) a través de los agujeros de las PATAS (T y U).
PASO 12 PASO 17 Fije tres BISAGRAS DE RESORTE (EE) a la PUERTA GRANDE (L). Utilice seis TORNILLOS NEGROS DE CABEZA PERDIDA de 13 mm (SS). Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso.
PASO 23 PASO 28 Deslice las PATAS (T y U) dentro de las muescas de los FALDONES (Q y R). Fije tres BISAGRAS (EE) a la PUERTA GRANDE (L). Utilice seis TORNILLOS NEGROS DE CABEZA PERDIDA de 13 mm (SS). Utilice un martillo para golpear una TUERCA (DD) a través de los agujeros de las PATAS (T y U). Ahora, gire un DESLIZAMIENTO AJUSTABLE (CC) dentro de cada TUERCA como se muestra en el diagrama superior. Fije los FALDONES (Q y R) al FONDO (F).
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded dresser drawers and shelves. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded drawers and shelves can break. • Never exceed the weight limits shown in the instructions. • Work from bottom to top when loading shelves and drawers.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Cajones y estantes sobrecargados. • Un riesgo de lesiones. • El mobiliario inestable puede volcarse. • Los cajones o estantes sobrecargados pueden romperse. • Nunca exceder los límites de peso indicados en las instrucciones.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 800-523-3987 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
