Full Product Manual

ManualsBrandsSartodoors ManualsDoors & Windows4002 48 in. x 80 in. Single Panel Black Finished Pine Interior Door Slab with Hardware

Table Of Contents

INSTALLATION

MANUAL

www.sartodoors.com

TOOLS REQUIRED:

• Tapeline

• Knife

• Drill

• Screwdriver

• Compound miter saw or handsaw

• Adhesive (“liquid nails” or PVA in the bottle with a narrow nozzle)

Step 1

Check the completeness of the product

before installation.

1. Door leaf – 2 pcs

2. Doorframe set (Pic. 1.1):

2.1. Jamb – 2 pcs

2.2. Head – 1 pcs

3. Door latch with a handles and

strike plate – 1 set (Pic. 1.2)

4. Door hinge – 2 pcs (Pic. 1.3)

5. Casing set for two door sides:

5.1. Side casing – 4 pcs

5.2. Head casing – 2 pcs

6. Weather strip (seal)

Step 11

Install the door latch and the handles (3) on the active door leaf (Pic. 23, Pic. 24) and the strike plate on the

inactive door leaf (Pic. 25) according to installation instructions.

Step 12

Cut o the side casings (5.1) to ensure that they are higher than the doorframe on 9/16” (Pic. 26).

Remove the lateral leg in order to t the side casing (Pic. 27).

Apply the adhesive on the inner side of the casings leg (Pic. 28) and insert the side casings into the grooves

of the doorframe (Pic. 29).

Measure the distance between

the side casings (Pic. 30).

Cut o the head casings (5.2)

of required length.

Apply the adhesive on the inner

side of the casing leg (Pic. 28) and

insert the top casing into

the groove of the doorframe.

Pic. 1.1

Pic. 1.2

Pic. 1.3

Step 10 (Pic. 17)

Insert the door leaves (1) into

the doorframe and x the

hinges with the screws in the pre-marked places (see the step 4).

Pic. 22

Pic. 23 Pic. 24 Pic. 25

Pic. 26 Pic. 27

Pic. 28 Pic. 29 Pic. 30

2.2 2.1

Step 9 (Pic. 16)

Insert the weather strip

(seal) (6) into the

doorframe grooves (2).

Pic. 21

’’French doors’’

Summary of content (2 pages)

PAGE 1
Step 9 (Pic. 16) Insert the weather strip (seal) (6) into the doorframe grooves (2). Step 10 (Pic. 17) Pic. 21 Insert the door leaves (1) into the doorframe and fix the hinges with the screws in the pre-marked places (see the step 4). INSTALLATION MANUAL Pic. 22 Step 11 Install the door latch and the handles (3) on the active door leaf (Pic. 23, Pic. 24) and the strike plate on the inactive door leaf (Pic. 25) according to installation instructions. ’’French doors’’ www.sartodoors.com Pic. 23 Pic.
PAGE 2
Step 2 Cut the jambs up to the length “L” (Pic. 2). L = H + 7/8” + Y H – Door leaf height Y – Gap between the door leaf and the ﬂoor Pic. 2 If needed, cut the head up to the length “S” at an angle 45° (parallel to the original head edge (Pic. 3)). Pic. 3 Pic. 10 Pic. 11 Pic. 12 Pic. 13 W 24’’ 28’’ 30’’ 32’’ 36’’ 42’’ S 48 - 1/2’’ 56 - 1/2’’ 60 - 1/2’’ 64 - 1/2’’ 72 - 1/2’’ 84 - 1/2’’ W – Door leaf width Step 3 Pic. 9 Drill and mill seats for the latch on the active door leaf(Pic.