INSTRUCTION MANUAL Split System Air Conditioner COOL/FAN Model Wall-mounted type Ceiling-mounted type Recessed type KS2432 TS2432 XS1822, XS1852 KS3032 TS3632 XS2432 KS3632 TS4232 XS3632 XS4232 Save These Instructions! Pub.
Features These air conditioners are equipped with cooling function. Details on this function are provided below; refer to these descriptions when using the air conditioner. • Microprocessor Controlled Operation The interior compartment of the remote control unit contains several features to facilitate automatic operation, easy logically displayed for easy use.
Contents Page Features.................................................................................................................. 2 Product Information .............................................................................................. 3 Alert Symbols ........................................................................................................ 3 Installation Location..............................................................................................
Installation Location We recommend that this air conditioner be installed properly by qualified installation technicians in accordance with the Installation Instructions provided with the unit. Before installation, check that the voltage of the electric supply in your home or office is the same as the voltage shown on the nameplate. • • • • Avoid: Do not install this air conditioner where there are fumes or flammable gases, or in an extremely humid space such as a greenhouse.
Names of Parts Each air conditioner as shown below consists of an indoor unit and an outdoor unit. You can control the air conditioner with the remote control unit.
Unit Display and Operation Selector Recessed type OPERATION lamp Ceiling mounted type TIMER lamp Recessed type Remote control receiver Ceiling mounted type Operation selector Finger-hold Air intake grille Air intake grille Air filter Operation selector 6 OI-201-06EG
Unit Display and Operation Selector (continued) INDOOR UNIT REMOTE CONTROL receiver OPERATION lamp TIMER lamp REMOTE CONTROL receiver Operation selector This section picks up infrared signals from the remote control unit (transmitter). Operation selector ON position This position is for operating the air conditioner with the wireless remote control unit. Set the selector normally in this position.
Remote Control Unit (Display) Displayed when main unit sensor is in use Displayed when setting temperature 1HR. SET TEMP Displayed when transmitting data F Displayed when temperature is shown Displayed when the temperature setting is at the upper or lower allowable limit ON AM PM OFF Displayed when setting timer Symbols (1) Operation mode (3) Set temperature 60 – 88 °F When set to 82 °F ........... COOL ....................................... F Current temperature indication ..................
Remote Control Unit AIR CONDITIONER Sensor Transmitter AIR CONDITIONER 1HR. SET TEMP F Display ON AM PM A OFF (Cover closed) 1HR. TIMER TEMP. 1 HR. TIMER button TEMP.
Remote Control Unit (continued) PROGRAM button For details, see ‘‘Setting the Timer’’. Press this button to select the mode you want to program. TIMER SELECT button No display : : OFF : ON : MODE selector button (COOL) (FAN) Use this button to select COOL or FAN mode : The air conditioner makes the room cooler. : The air conditioner works only as a circulation fan. FLAP button Press this button to select the sweep function, which moves the flap up and down automatically.
Using the Remote Control Unit How to Install Batteries ACL button 1. Slide the cover in the direction indicated by the arrow and remove it. 2. Install two AAA alkaline batteries. Make sure the batteries point in the direction marked in the battery compartment. 3. Use a thin object such as the tip of a pen to press the ACL button. NOTE • • • • How to Use the Remote Control Unit The batteries last about six months, depending on how much you use the remote control unit.
Using the Remote Control Unit (continued) Mounting the Remote Control Unit Removable mounting Non-removable mounting Wall Wall (Packed in the indoor unit) (Packed in the indoor unit) Mounting on a wall A. Removable mounting 1) Momentarily hold the remote control unit at the desired mounting position. 2) Confirm that the air conditioner responds correctly when you press keys on the remote control from that position.
Operation with the Remote Control Unit 1. Operation AIR CONDITIONER 1HR. F 1 AM A 1HR. TIMER TEMP. STEP 3 ON I /OFF STEP 2 STEP 1 MODE OFF ON CLOCK NIGHT SETBACK FLAP HH TIMER FAN SPEED MM SELECT STEP 5 STEP 4 SELECT TIME SET ACL A/C SENSOR BATTERIES NOTE Check that the circuit breaker on the power panel is turned on and that the operation selector of the indoor unit is in the ON position. Press the setting buttons as described below and change the settings as desired.
Operation with the Remote Control Unit (continued) NOTE • Choose the best position in the room for the remote control unit, which also acts as the sensor for room comfort and transmits the operating instructions. Once you’ve found this best position, always keep the remote control unit there. • This appliance has a built-in 3-minute time delay circuit to ensure reliable operation. When the operation button is pressed, the compressor will start running within three minutes.
Operation with the Remote Control Unit (continued) 4. Night Setback Mode AIR CONDITIONER 1HR. F A PM 1HR. TIMER TEMP. ON I /OFF MODE OFF ON CLOCK NIGHT SETBACK FLAP HH TIMER FAN SPEED MM SELECT Night Setback Mode is used for saving energy. Press the NIGHT SETBACK button while operation. mark appears in the display. The To release the night setback function, press the NIGHT SETBACK button again. NOTE In Cooling Mode: ( ) The night setback mode cannot be used during automatic operation.
Special Remarks Power failure during operation Remote Control Unit 16 • In the event of power failure, the unit will stop. When the power is resumed, the unit will restart automatically after three minutes. • The remote control unit sends the setting condition to the air conditioner regularly at three minute intervals.
Setting the Timer ON I /OFF MODE OFF ON CLOCK NIGHT SETBACK FLAP HH TIMER FAN SPEED MM SELECT SELECT TIME SET ACL A/C SENSOR BATTERIES 1. How to set the present time (Example) To set to 9:10 p.m. Operation 1. Press the Program button ( times. Indication OFF ON CLOCK ) three The time indication alone flashes. 2. PM • • 2. How to set the OFF time Press the HH button until PM 9 is The display will automatically stop flashing displayed.
Setting the Timer (continued) 3. How to set the ON time (Example) When air conditioner is off, starting operation at 7:10 a.m. Operation 1. Press the Program button ( ON AM Indication OFF ON CLOCK ) twice. The timer ON and time indications flash. 2. • • Press the HH button until AM 7 is The display will change automatically back to show displayed. the present time after 10 Press the MM button until 10 is displayed. sec. 3. Press the TIMER SELECT button three The times to set ON time.
Using the 1-Hour OFF Timer 1. 1-Hour OFF Timer 1HR. 1HR. TIMER This function causes the unit to operate for one hour and then stop, regardless of whether the unit is on or off when this button is pressed. indicator in the display indicates that this function is operating. The 1 HR. Setting procedure: Regardless of whether the unit is operating or stopped, press the 1 HR. TIMER button. appears in the display. 1 HR.
Adjusting the Airflow Direction A. Horizontal (Wall mounted type only) The horizontal airflow can be adjusted by moving the vertical vane to the left or right. Indoor unit (Wall mounted type) Left Right Vertical vane B. Vertical Confirm that the remote control unit has been turned on. Press the FLAP button to start the flap moving up and down ( ). If you want to stop the flap movement and to direct the air in the desired direction, press the FLAP button again.
Care and Cleaning 1. For safety, be sure to turn the air conditioner off and also to disconnect the power before cleaning. 2. Do not pour water or spray detergent on the indoor unit to clean it. This will damage the internal components and may cause an electric shock or fire. Air Intake and outlet side (Indoor Unit) Clean the air intake and outlet side of the indoor unit with a vacuum cleaner brush, or wipe them with a clean soft cloth.
Care and Cleaning (continued) How to remove the filter Ceiling mounted type: 1. Remove the bolt screws on the latch using a screwdriver. (After cleaning, be sure to reattach the two bolt screws.) 2. Take hold of two latches on the air intake grille and press it to the rear, and the grille will open downward. 3. Take hold of the finger-hold on the air filter, first lift it and then pull it toward you to release it from the catch.
Troubleshooting If your air conditioner does not work properly, first check the following points before requesting service. If it still does not work properly, contact your dealer or service center. Trouble Air conditioner does not run at all. Possible Cause 1. Power failure. 2. Leakage breaker tripped. 3. Line voltage is too low. 4. ON/OFF operation button is OFF. 5. Batteries in remote control unit have run down. 1. Obstruction in front of condenser coil. 1. Dirty or clogged air filter.
SANYO FISHER COMPANY A DIVISION OF SANYO NORTH AMERICA CORPORATION 21605 Plummer Street Chatsworth, CA 91311 U.S.A. In Canada SANYO Canada Inc.