User Manual

Operating _21
02 OPERATING
USING THE CONTROL PANEL
Basic temperature of Freezer and
Refrigerator Compartments
The basic temperature and/or recommended
temperature of Freezer and Refrigerator
Compartments are -19 °C and 3 °C respectively.
If the temperature of Freezer and Refrigerator
Compartments are too high or low, adjust the
temperature manually.
Controlling the Freezer temperature
The Freezer temperature can be set between
-14 ºC and -22 ºC to suit your particular needs.
Press the Freezer button repeatedly until the
desired temperature is shown in the temperature
display. Keep in mind that foods like ice cream
may melt at -15 ºC. The temperature display will
move sequentially from -22 ºC to -14 ºC. When the
display reaches -14 ºC, it will begin again at -22 ºC.
Controlling the Refrigerator temperature
The Refrigerator temperature can be set between
7 ºC and 1 ºC to suit your particular needs. Press
the Fridge button repeatedly until the desired
temperature is shown in the temperature display.
The temperature control process for the Fridge
works just like the Freezer process.
Press the Fridge button to set your desired
temperature. After a few seconds, the Fridge
will begin adjusting towards the newly set
temperature. This will be refl ected in the digital
display.
- The temperature of the Freezer,
Refrigerator or pantry room may rise when
you open the doors too frequently, or if a large
amount of warm or hot food is placed inside.
- This may cause the digital display to blink. Once
the Freezer and Refrigerator temperature return
to their normal set temperatures, the blinking
will stop.
- If the blinking continues, you may need to
“reset” the Refrigerator. Try unplugging the
appliance, wait for around 10 minutes and then
plug the power cord back in.
- The temperature of the pantry room may be a
little different according to the location inside.
- If communication between display and Main
Controller errors, Pantry display light may blink.
Once the pantry room return to their normal
set temperatures, the blinking will stop. If the
blinking continues for a long period of time,
please contact to Samsung Electronics Service
Center.
USING THE COLD WATER DISPENSER
Press the Ice / Water button to select the type of
you want.
• Place a glass underneath the ice dispenser and
push gently against the dispenser lever with
your glass. Make sure the glass is in line with
the dispenser to prevent the ice from bouncing
out.
• Please wait 2 seconds before removing the
glass under the dispenser to prevent spills. If the
Refrigerator door opens, the dispenser does not
work.
• When Cubed Ice is selected after using the
Crushed Ice feature, a small amount of residual
crushed ice might be produced.
• Water Dispenser Installation
After installation, press the dispenser arm for at
least 2 minutes to remove trapped air from the
water line and to fi ll the water system.
• In case ice doesn’t come out, pull out the ice
bucket and press test button located on the
right side of ice-maker.
• Do not press the test button continuously when
the tray is fi lled with ice or water as illustration.
Water may overfl ow or ice jamming may occur.
• Normal Use
To fi ll ice bucket to maximum capacity after
installation, make sure to do the following steps.
1. Allow your refrigerator to operate and cool
down for 24 hours (or 1 full day).
2. Waiting 24 hours will allow your ice maker to
cool properly.
3. Dispense 4 to 6 ice cubes into the glass.
4. After 8 and 16 hours, dispense a full glass of
ice at each time.
No ICE
Select this if you want
to turn ice-maker off.
PUSH
DA99-03403B-09.indb 21DA99-03403B-09.indb 21 14. 5. 9.  3:2414. 5. 9.  3:24