Quick Guide

ManualsBrandsSamsung ManualsHome Appliances6.3 cu. ft. Smart Instant Heat Induction Slide-in Range

DG68-01302A-01

Electric Range

Installation manual

Anti-tip device

WARNING

To reduce the risk of tipping the appliance, the appliance must be secured by properly installed anti-tip devices packed with the appliance.

A. A child or adult can tip the range and be killed.

B. Install the anti-tip device to the structure and/or the range at rear right (or rear left) of the range bottom.

C. Engage the range to the anti-tip device by leveling leg at rear right (or rear left) of the range bottom.

D. Re-engage the anti-tip device if the range is moved.

E. See installation instructions for details.

F. Failure to do so can result in death or serious burns to children or adults.

About this manual

READ THESE INSTRUCTIONS COMPLETELY AND CAREFULLY.

Important note to the installer

• Read all instructions contained in these installation instructions before installing the range.

• Remove all packing materials from the oven compartments before connecting the electrical supply to the range.

• Observe all governing codes and ordinances.

• Save for the local electrical inspector’s use.

• Be sure to leave these instructions with the consumer.

Important note to the consumer

Keep these instructions for the local electrical inspector’s use.

• As when using any appliance generating heat, there are certain safety precautions you should follow.

• Be sure your range is installed and grounded properly by a qualied installer or service technician.

• For the range to ventilate properly, make sure the range’s vents are not blocked or covered, and that there is enough clearance at the top,

back, sides, and underneath the range. The vents allow the necessary exhaust for the range to operate properly with correct combustion

and get the good cooking result.

• Make sure the wall coverings around the range can withstand the heat generated by the range.

• To eliminate the need to reach over the surface elements, avoid having cabinet storage space above the cooktop.

• The range should not be placed on a base.

For your safety

WARNING

• If the information in this manual is not followed exactly, a re or electrical shock may result causing property damage, personal injury, or

death.

• Before beginning the installation, switch the power off at the service panel and lock the service disconnecting switch to prevent power

from being switched on accidentally. When the service disconnecting switch cannot be locked, securely fasten a prominent warning

device, such as a tag, to the service panel.

• This appliance must be properly grounded.

Install_NE63T8911_AA_DG68-01302A-01_EN+MES.indb 1Install_NE63T8911_AA_DG68-01302A-01_EN+MES.indb 1 2021-01-29  6:21:182021-01-29  6:21:18

Summary of content (16 pages)

PAGE 1
Electric Range Installation manual Anti-tip device WARNING To reduce the risk of tipping the appliance, the appliance must be secured by properly installed anti-tip devices packed with the appliance. A. A child or adult can tip the range and be killed. B. Install the anti-tip device to the structure and/or the range at rear right (or rear left) of the range bottom. C. Engage the range to the anti-tip device by leveling leg at rear right (or rear left) of the range bottom. D.
PAGE 2
Preparing to install the range Prepare tools & Parts The tools you will need Drill Adjustable Wrench Pliers 1⁄4" Nut Driver Phillips Screwdriver What’s included with your range Anti-tip Bracket Template Anti-Tip Bracket Flat Screwdriver Pencil Level Additional materials you may need Screws (short:2 ea, long:2 ea) Filler Kit 4-Wire Cord or 3-Wire Cord (UL Approved 40 or 50 AMP) Strain Relief (For Conduit Installation Only) Checking the installation site Clearances and dimensions To install t
PAGE 3
Optional rear filler kit Used to fill gap between the range back and wall. Adds a filler strip to the rear of the range. This kit can only be used when the opening in the countertop is 25" deep. 1. Unscrew the screws affixing the vent cover. 2. Assemble the filler strip to the back of the range using the removed screws. NOTE If the countertop depth is greater than 25", there will be a gap between the filler kit and the back wall.
PAGE 4
Connecting the power Step 1. Meeting electrical connection requirements CAUTION For personal safety, do not use an extension cord with this appliance. Remove the house fuse or open the circuit breaker before beginning installation. This appliance must be supplied with the proper voltage and frequency, and be connected to an individual, properly grounded branch circuit, protected by a circuit breaker or fuse having amperage as specified on the rating plate.
PAGE 5
Step 2. Accessing the power cord connection Loosen and then remove the rear access cover screw with a screwdriver. Remove the rear access cover by pull right and then out. The terminal block will then be accessible.
PAGE 6
Installing a 4-wire power cord WARNING Black Live 1 White The neutral wire of the supply circuit must be connected to the neutral terminal located in the lower center of the terminal block. The power leads must be connected to the lower left and the lower right terminals of the terminal block. The 4th grounding lead must be connected to the frame of the range with the ground plate and the ground screw. Red Neutral terminal Ground strap 1. Remove the 3 lower terminal screws from the terminal block.
PAGE 7
Installing a 4-wire conduit • Red Black White Neutral terminal Live 1 Ground strap 1. Wire tips Live 2 Black Ground plate • Red White Ground wire (Green) 2. 3. 4. 5. 6. 7. Aluminum building wire may be used but it must be rated for the correct amperage and voltage to make the connection. Connect the wires as described below. The wire you use, the location and enclosure of splices, etc., must conform to good wiring practices and local codes.
PAGE 8
1. Install the bracket using the template The Anti-Tip bracket is packaged with a template. The instructions include information necessary to complete the installation. Read and follow the instructions on the sheet (template) for range installation. 2. Level the range Level the range by adjusting the leveling legs with a wrench. Raise range Lower range Leveling leg 3. Check your adjustments Use a spirit level to check your adjustments.
PAGE 9
Estufa eléctrica Manual de instalación Dispositivo anti inclinación ADVERTENCIA Para reducir el riesgo de inclinaciones, el artefacto debe quedar correctamente fijado mediante la instalación de los dispositivos anti inclinación que vienen con el equipo. A. Un niño o un adulto podrían inclinar la estufa y morir. B. Instale el dispositivo anti inclinación en la estructura y/o en la parte posterior derecha (o posterior izquierda) de la base de la estufa. C.
PAGE 10
Preparación para instalar la estufa Prepare las herramientas y las piezas Las herramientas que necesitará Taladro Llave ajustable Pinza Llave para tuercas de 1/4" Destornillador Phillips Elementos incluidos con su estufa Plantilla de ménsula anti inclinación Ménsula anti inclinación Destornillador plano Lápiz Nivel Materiales adicionales que puede necesitar Tornillos (cortos: 2, largos: 2) Kits de relleno Cable de 4 conductores o cable de 3 conductores (de 40 o 50 AMP aprobados por United Lab
PAGE 11
Kit de relleno trasero opcional Se usa para llenar el espacio entre la parte trasera de la estufa y la pared. Agrega una tira de relleno a la parte trasera de la estufa. Este kit solo puede usarse cuando la abertura en la mesada tiene una profundidad de 25". 1. Desatornille los tornillos que fijan la tapa de ventilación. 2. Ensamble la tira de relleno a la parte posterior de la estufa con los tornillos que haya retirado.
PAGE 12
Cómo conectar la alimentación eléctrica Paso 1. Cumplimiento de los requisitos de conexión eléctrica PRECAUCIÓN Para seguridad de las personas, no utilice cables prolongadores con este electrodoméstico. Retire el fusible de la casa o corte la electricidad con el disyuntor antes de comenzar la instalación.
PAGE 13
Paso 2. Acceso a la conexión del cable de alimentación Afloje y luego retire el tornillo de la cubierta de acceso posterior con un destornillador. Retire la cubierta de acceso posterior jalando hacia la derecha y luego hacia afuera. Habrá quedado abierto el acceso al cuerpo de terminales.
PAGE 14
Instalación de un cable de alimentación de 4 conductores ADVERTENCIA Negro Fase 1 Blanco El conductor neutral del circuito de alimentación debe conectarse a la terminal ubicada en la parte central inferior del cuerpo de terminales. Los chicotes de cable que portan corriente deben conectarse a las terminales inferior izquierda e inferior derecha del cuerpo de terminales. El cuarto chicote de conexión a tierra debe conectarse al marco de la estufa con la chapa y el tornillo de conexión a tierra.
PAGE 15
Instalación de un conducto de 4 conductores • Rojo Negro Blanco Cinta de conexión a tierra Terminal neutra • Fase 1 1. Fase 2 Puntas de conductor Negro Chapa de conexión a tierra Rojo Blanco Conductor a tierra (Verde) 2. 3. 4. 5. 6. 7. Se puede utilizar alambre de construcción de aluminio pero debe estar graduado y aprobado para los amperajes y voltajes correctos para hacer la conexión. Conecte los conductores según se describe a continuación.
PAGE 16
1. Instale la ménsula utilizando la plantilla. La ménsula anti inclinación se encuentra empacada junto con una plantilla. Las instrucciones incluyen la información necesaria para completar la instalación. Lea y siga las instrucciones en la hoja (plantilla) para la instalación de la estufa. 2. Nivelación de la estufa Nivele la estufa ajustando las patas niveladoras con una llave. Levantar la estufa Bajar la estufa Pata niveladora 3.