SHR-2040/2041/2042-ENG-1 2005.6.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page ii SHR-2040/2041/2042 USER’S MANUAL Safety Regulations Please be sure to keep the following in mind for the right use of the product to pre-vent proprietary risk or damage. ■ Do not use multiple plugs at once. ● ■ Do not put a vase, flowerpot, cup, cosmetics, medicine, or vessel with water around you. ● ■ This may cause fire. Do not disassemble, repair, or remodel the product. ● ■ This may cause abnormal operation due to high temperature.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page iii Before we start This User’s Manual describes the basic usage of SHR-2040/2041/2042. This Manual contains all the matters necessary for using SHR-2040/2041/2042 such as brief instruction, part name, function, connecting other equipment, and menu setup of SHR-2040/2041/2042. - SEC retains the copyright on this User’s Manual. This User’s Manual cannot be copied without SEC’s prior written approval.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page iv Contents ii Safety Regulations iii Before we start Standards Approvals 1 1-1 1. Introduction 1-2 2. Features 1-3 3. Part Names and Functions 2 Chapter 2 Installation 2-1 1. Installation Environment Setup 2-2 2. Checking Product & Accessory 2-3 3. HDD Addition 3 Chapter 3 Connecting with Other device 3-1 1. Connecting Video, Audio, & Monitor 3-3 2. Connecting the Network 3-5 3. Connecting the USB 3-6 4.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page v 5 Chapter 5 Menu Setup 5-1 Before Use 5-2 1. System 5-12 2. Camera 5-16 3. Monitoring 5-18 4. Recording Mode 5-20 5. Event Record Mode 5-25 6. Record Schedule 5-27 7. Backup 5-28 8. Network 5-32 9. Network Setup 6 Chapter 6 PTZ Camera Control 6-1 1. PTZ camera Control Mode 6-3 2. Basic Operation of PAN, TILT, & ZOOM 6-4 3. Preset Setup 6-6 4. Camera Menu Setup 6-7 5. Preset View 6-8 6.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM 9 Chapter 9 Smart Viewer 9-1 1. Introduction 9-2 2. Feature 9-3 3. PC Specification(Recommendation) 9-4 4. Smart Viewer Installation 9-7 5. Smart Viewer Program Execution 9-8 6. Smart Viewer Initial Screen 9-9 7. Monitoring Mode 9-23 8. Search Mode 9-30 9. Setup Mode 10 Appendix 10-1 1. Product Specification 10-4 2. The specification of HDD and peripheral device 10-5 3. Outline Drawings 10-7 4. Factory Default 10-9 5.
SHR-2040/2041/2042-ENG-1 2005.6.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 1-1 SHR-2040/2041/2042 USER’S MANUAL 1 Introduction The Digital Video Recorder(DVR) compresses the 4 channel of camera input data into the MPEG4 video file and the 4 channel of voice input data into the ADPCM audio file in the real time to record them in the Hard Disk or retrieve them from the Hard Disk simultaneously.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 1-2 2 Features ■ 4 CH Composite Input Connectors ■ NTSC / PAL Video Source Compatible ( NTSC : SHR-2040/SHR-2041/SHR2042, SHR-2040N / SHR-2041N / SHR-2042N PAL : SHR-2040P/SHR-2041P/SHR2042P) ■ Able to record the CIF sized (NTSC-352 x 240/PAL-352 x 288) video at the speed of 120 ips(NTSC)/100ips(PAL)(Image Per Second) ■ 4 CH Loop Through Video Connectors ■ Hard Disk Overwrite Mode ■ Large Quantity Hard Disk Backup by USB2.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 1-3 SHR-2040/2041/2042 USER’S MANUAL 3 Part Names and Functions [SHR-2040] No. Name 1 Displays power on/off condition. Alarm LED lights on when an event occurs. HDD Access LED Displays Normal Access to HDD. Upon Access to HDD, LED repeats on and off. Network LED Displays both network connection and data transmission conditions. Backup LED Displays Back Up Mode. Rec LED 1 2 4 ...
SHR-2040/2041/2042-ENG-1 2005.6.29 No. 4:58 PM Page 1-4 Name Function PTZ 7 ZOOM 8 TELE FREEZE 9 WIDE SEARCH 10 VIEW MENU 11 PRESET 12 PTZ Button Performs the TELE, WIDE, PRESET, and VIEW function. ZOOM(TELE) Button Sets up Digital Zoom(x2). ( Performs the TELE function by pressing the PTZ button.) FREEZE(WIDE) Button Performs the FREEZE function in the DISPLAY Mode. ( Performs the WIDE function by pressing the PTZ button.) SEARCH(VIEW) Button Displays the search method.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 1-5 SHR-2040/2041/2042 USER’S MANUAL [SHR-2041] [SHR-2042] No. Name 1 Displays power on/off condition. Alarm LED lights on when an event occurs. HDD Access LED Displays Normal Access to HDD. Upon Access to HDD, LED repeats on and off. Network LED Displays both network connection and data transmission conditions. Backup LED Displays Back Up Mode. Rec LED Eject Button 2 1 3 4 ...
SHR-2040/2041/2042-ENG-1 2005.6.29 No. 4:58 PM Page 1-6 Name Function Displays 4 split screen. Displays the selected channel to the Single Mode MODE 7 Mode Selection Button Displays both LIVE Channel and Playback Channel in the PIP Screen simultaneously. Search Displays 6 split screen. (1 CH playback screen and 4 CH live screen) Displays 9 split screen.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 1-7 SHR-2040/2041/2042 USER’S MANUAL [SHR-2040] Caution Do not play DVR on the carpet or other soft material to prevent clogging of the air ventilator. To play DVR on the cabinet or rack, be sure to check the ventilation condition. No. Function Composite Video Signal Input Port (BNC Style Connector) 1 VIDEO IN 2 THROUGH You may use THROUGH port to transmit a video signal to the other video equipment.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 1-8 [SHR-2041/2042] Caution Do not play DVR on the carpet or other soft material to prevent clogging of the air ventilator. To play DVR on the cabinet or rack, be sure to check the ventilation condition. No. Name Function 1 VIDEO IN 2 THROUGH You may use THROUGH port to transmit a video signal to the other video equipment.
SHR-2040/2041/2042-ENG-1 2005.6.
SHR-2040/2041/2042-ENG-1 2005.6.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 2-1 SHR-2040/2041/2042 USER’S MANUAL 1 Installation Environment Setup Do not play DVR on the carpet or other soft material to prevent clogging of the air ventilator. To play DVR on the cabinet or rack, be sure to check the ventilation condition. You should pay attention to the following before you use the product. 1. Do not use it outdoor. 2. Do not let water or liquid in the connection part or the product itself. 3.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 2-2 2 Checking Product & Accessory Upon delivery of a product, you shall unwrap the product and put it on the even floor or where you want to use it. Then you shall check if the following items are in it. ■ ■ ■ ■ ■ ■ ■ Main Body User’s Manual One Power Cord Two Brackets - These are not supplied in SHR-2040. - Brackets are used to attach the product to the rack.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 2-3 SHR-2040/2041/2042 USER’S MANUAL 3 HDD Addition You can add up HDD to the product.(2040-1 HDD/2041-3 HDDs/2042-2 HDDs) However, since the product contains has many parts which may incur electric shock, accident, or product breakdown and improper installation or setup may disturb HDD recognition or normal product operation, you shall consult with an expert of the agency where you bought the product.
SHR-2040/2041/2042-ENG-1 2005.6.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 2-5 SHR-2040/2041/2042 USER’S MANUAL 2. Detach the cover from the product. (Pull out the cover slightly and lift from the back side to detach.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 2-6 3. A bracket(BRACKET- HDD) is mounted to each side of product to fix the HDD. Please loosen the screw of the bracket to which you want to fix HDD.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 2-7 SHR-2040/2041/2042 USER’S MANUAL 4. Pull BRACKET-HDD to the product center to detach the fixed part at the bottom and detach BRACKET-HDD from the product. 5. Tighten 4 special screws(BWH,6-32UNC,L10.5), supplied as an accessory to fix HDD to BRACKET-HDD. (A force to tighten the screw shall be strong enough to resist vibration.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 2-8 6. Reattach HDD to the original position of BRACKET-HDD. (Assembly shall be done in the reverse procedure of disassembly as follows. Align the 5 fixing points at the bottom with the BRACKET-HDD fixing holes respectively and push BRACKET-HDD out of the product to align the screw fixing holes. Then, tighten the screws firmly.) 7.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 2-9 SHR-2040/2041/2042 USER’S MANUAL 8. Check the connector, wiring, and cable fixing condition inside the product and close the cover. 9. Tighten cover-fixing screws. (5 points on both sides and 1 point in the back side) ✻ You can apply 2 HDDs to each BRACKET-HDD as shown in the figure. Caution For HDD addition, please select the same HDD with the existing HDD fixed to the product as far as possible.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 2-10 WARNING ! Regarding the sub fan, you need additional brackets and sub fans as follows. The sub fan is shaped like this when viewed from the front and back. Please pay attention to the fan direction to let wind go through the fan.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 2-11 SHR-2040/2041/2042 USER’S MANUAL # Please install the fan which is seen at the right from the front view of SHR-set as follows.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 2-12 $ The cable should be out from the left hole.
SHR-2040/2041/2042-ENG-1 2005.6.
SHR-2040/2041/2042-ENG-1 2005.6.
SHR-2040/2041/2042-ENG-1 2005.6.
SHR-2040/2041/2042-ENG-1 2005.6.
SHR-2040/2041/2042-ENG-1 2005.6.
SHR-2040/2041/2042-ENG-1 2005.6.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 3-5 SHR-2040/2041/2042 USER’S MANUAL 3 Connecting the USB 1. There are two USB connecting ports on the front and back of SHR-2040/2041/2042. 2. USB Hard Disk, USB CD/DVD, and USB Memory are connected through the front and back ports of SHR-2040/2041/2042. 3. Only one USB device can be connected with each USB connecting port. 4. If the USB HDD is connected to the system, it should be detected and set through Menu - System - HDD setup before the operation.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 3-6 4 Connecting the Alarm Input/Output The Alarm IN/OUT port in the back of SHR-2040/2041/2042 is composed of the following elements. ● ALARM IN/OUT Connection Name Function - ALARM IN1 - ALARM IN2 - ALARM IN3 - ALARM IN4 ALARM Input Port 2 - ALARM RESET IN On receiving an ALARM RESET signal, the system cancels the current ALARM input and output signal and then resumes sensing.
SHR-2040/2041/2042-ENG-1 2005.6.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 3-8 5 Connecting the RS-485 Device ● Connect the RS-485 Device through the back port of SHR- SHR-2040/2041/2042. ● You can install and control the PTZ camera supporting the RS-485 communication. ● You can adopt either Half Duplex or Full Duplex method for the connection.
SHR-2040/2041/2042-ENG-1 2005.6.
SHR-2040/2041/2042-ENG-1 2005.6.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 4-1 SHR-2040/2041/2042 USER’S MANUAL 1 System Operation ● Turn the power on and the following LOGO pops up on the screen. ● After the LOGO appears, all of LED in the front flickers 6 times to initialize the system for operation. ● Upon completion of normal initialization, the Live screen appears accompanying a beep sound. ● It requires 30 to 40 seconds until the Live screen appears.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 4-2 2 Live screen Mode Definition of Live Screen Icon The Live screen icons display the current setup and function status of each screen. N PTZ CAM_01 V.Loss CAM_01 P E S : Recording Icon Each icon represents Normal / Event (Alarm + Motion) / Schedule Recording. : Recording Video Size Icon Each icon represents the recording size of Large / Normal / CIF.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 4-3 SHR-2040/2041/2042 USER’S MANUAL : Auto sequence Icon This icon appears in the auto sequence mode. : Backup Playback Icon This icon appears when the backup data is played. : Fan Error Icon This icon appears when the fan stops. : This icon appears when there is no HDD. V.Loss / V.Off : Video Input Status If there is no more video data input in the Video On, [V.Loss] appears in the channel. If you set Video On/Off to Off, [V.Off] will appear.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 4-4 Selecting Live Screen Mode Each mode may be selected by [MODE Button] and [CH1 ~ CH4 Button]. The following figure shows Live Mode after converted. ● The default setup is 4 Split Screen Mode. ● You are able to choose other modes than Full Screen Mode by the [MODE] button in sequence. Whenever you press the [MODE] button, the system will change [4Split]➝[PIP]➝[auto sequence]➝[4 Split] in sequence.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 4-5 SHR-2040/2041/2042 USER’S MANUAL 3 Live Channel Selection and Audio On/Off Setup In other split modes than Full Screen Mode and Auto Sequence Mode, you can choose a channel to be displayed in each split area on your own. In addition, the channel being set to Audio On can be set to Audio On/Off in all Live Modes.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 4-6 4 Freeze and Zoom Freeze Function Freeze function pauses the video image in the Live Screen, it is only available in the Live Mode. You can set Freeze On/Off with [FREEZE] Button and [FREEZE LED] is turned on or off depending on the Freeze On/Off setup condition. Zoom Function Zoom function enlarges the selected area to double size, and it is only available in the single mode. If the [ZOOM] button is pressed in the single mode, the Zoom area appears.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 4-7 SHR-2040/2041/2042 USER’S MANUAL 5 Event Monitoring Event monitoring displays the channel synchronized with a event on the screen when a special event (Sensor/Motion/Video Loss) occurs. Event monitoring On/Off and event duration setup is available in [Menu]➝[Monitoring] mode.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 4-8 6 Spot-out monitoring Spot-out Monitoring has nothing to do with Live Screen Output, it monitors the full screen of a certain channel. If you select the Monitoring in the MENU, the one channel among CH1 ~ CH4 is output with a Spot-out or channels are output one by one at an interval as Auto Sequence Mode in the Live Mode. Live screen icon does not appear in the spot-out monitoring. The interval is as same as the Auto Sequence time in the Live Mode.
SHR-2040/2041/2042-ENG-1 2005.6.
SHR-2040/2041/2042-ENG-1 2005.6.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 5-1 SHR-2040/2041/2042 USER’S MANUAL Before Use 5-1 ● Selection The yellow cursor shows the current window. Use the ,,¦, key in the front to move the cursor on your desirous menu. If you press the “Enter” key with the cursor clicking on your desirable menu, the system will enter the new mode. Press the “Enter” key to finish the selection. On seeing Drop Down Menu, use the or key to move the cursor on your desirable menu.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 5-2 1 System ● System Menu has the following items in detail. Date/Time/Language Setup ● Press the “Enter” key and the ¦, key to move to Y/M/D. Use the , key to change the date. Press the “Enter” key to come out of the mode. ● Time Press the “Enter” key and the ¦, key to move to H/M/S. Use the ¦, key to change the time. Press the “Enter” key to come out of the mode.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 5-3 SHR-2040/2041/2042 USER’S MANUAL Note [Date/Time Change] Pressing “OK” after you change date and time, you will be asked by a pop-up window if you really confirm the change. Here, press ”Yes” to change the time. Since Date/Time does not change in backup process, be sure to stop the backup process before you change Date/Time. If the date or time is changed, the system reboots.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 5-4 Password ● The Default Password is 4321. ● New Password This is used to change the system password inside SHR-2040/2041/2042. You are allowed to create a password up to 4 digits. Press the “Enter” key and a channel button from 1 ~ 4 at the left. Press the “Enter” key after change to move to “New Password Confirm”. ● New Password Confirm This confirms a new password. You shall be obliged to input New Password in the above row first.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 5-5 SHR-2040/2041/2042 USER’S MANUAL Load Factory Default ● It used to initialize all the menu setup values. The recorded data will not be deleted. Press “OK” in the confirmation window to start initializing. System Log ● ● ● ● ● ● 5-5 System Log is used to check the important record by an administrator. It displays such contents of a system related log and its execution date/time as System Start, System Termination, and Menu Setup Change.
SHR-2040/2041/2042-ENG-1 2005.6.29 ● 4:58 PM Page 5-6 System Log List System Start Login(Admin) Logout(Admin) Login(User) Logout(User) Setup Start (Local) Set Setup End (Local) Set Setup (Remote): Viewer Play Back Start Play Back End Record Start CH[N] Record End CH[N] Power Failure Recovery Starts the system. Viewer Login (Admin) Viewer Logout (Admin) Viewer Login (User) Viewer Logout (User) Enters into the menu. Comes out of menu. Sets the menu. Starts the playback. Ends the playback.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 5-7 SHR-2040/2041/2042 USER’S MANUAL System Information and Setup ● ● ● ● Software Version : Displays the current version. Setup is not available. Broadcast Format : Displays the current Format(NTSC/PAL) . Setup is not available. Mac Address : 6 Byte hardware address. Setup is not available. Device Erase This erases the data in ATA / USB HDD / USB memory.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 5-8 Caution [Device Erase] Data will not be deleted in the backup mode. Please be sure to stop the backup before you delete a data. In the recording mode, suspend the recording and delete a data. Caution [USB S/W Upgrade] Download the software to upgrade at http://www.sec.co.kr, CCTV Part. If the USB memory to upgrade has a format not being supported by DVR set, the upgrade is impossible.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 5-9 SHR-2040/2041/2042 USER’S MANUAL HDD Mode Setup ● HDD End Mode Stop : Stops recording when HDD is full during the recording. Overwrite : Deletes the original data and save a new data when HDD is full during the recording. ● HDD End Beep On : Beeps when the HDD is full in the recording mode. Off : Although the HDD is full in the recording mode, the beep sound is not heard. Note If the HDD is full, the Disk Full Icon( 5-9 ) is appeared.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 5-10 Caution [Disk Overwrite] In the overwrite Mode, the previous Event data is deleted and the mode is changed. Remote control Device ● MENU for the use of Samsung system keyboard Remote Control Device Device ● Samsung System Keybord ID Baudrate Parity Date Stop Duplex 03 4800 None 8 1 Half Duplex Device A Remote Control Device, being connected to the RS485 port. ● ID This is a private ID of SHR-2040/2041/2042.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 5-11 SHR-2040/2041/2042 USER’S MANUAL System Shutdown Remote Control Device ● Terminates the work in action safely and turns the power off. Press “OK” in the confirmation window and plug out when you see “Safe to Power Off”. Caution [System Shutdown] Power-off without terminating the system in the System Shutdown menu may incur improper motion like data loss and disk failure. Power-off shall be done in the System Shutdown menu.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 5-12 2 Camera ● The detailed Camera Menu items are as follows. Camera Config. ● Video On : Camera images from a selected channel appear. Off : Camera images from a selected channel disappear. Covert1 : Displays the information except for the Video information of selected channel. Covert2 : Does not display the any information. Audio/Cam name/Auto sequence setup are impossible in the Off channel. ● Audio On : Makes the sound of selected channel on.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 5-13 SHR-2040/2041/2042 USER’S MANUAL 5-13 ● Title You can name the camera of selected channel. If you press the [Enter] key, the Virtual keyboard will come out. Virtual Keyboard If you move the cursor, you can type text by text. Up to 15 texts can be typed. Keyboard cannot be composed of all spaces. Pressing Caps Lock changes the keyboard that can be selected.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 5-14 PTZ Device ● ID It is an ID for PTZ Camera and available to set from 0 to 255. ● Protocol It is supported by the PTZ device. The following protocols are now being supported. Samsung/ Vicon/ Panasonic/ AD/ Philips/ Erna/ PelcoD/ PelcoP/Vcltp/ Diamond/ Kalatel ● Baurate Baurate is supported by the PTZ device. 600/ 1200/ 2400/ 4800/ 9600/ 19200/ 38400 ● Parity It is set to the one of None, Even, and Odd. ● Data It is set to either 7 or 8.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 5-15 SHR-2040/2041/2042 USER’S MANUAL Screen Setup 5-15 ● It is a window to set Brightness/Contrast/Color for the camera image of each channel. Put the cursor on the channel that you want to adjust and set Brightness/Contrast/Color. Once selected, the channel appears in the right PIP area. Use the or button to adjust the value from 0 to 100.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 5-16 3 Monitoring ● Event Monitoring It is possible to set to Off/3sec/5sec/10sec/20sec/30sec/Continuous. ① Off : Event Monitoring does not operate to turn to the screen where an event occurs. ➁ 3sec/ 5sec/ 10sec/ 20sec/ 30sec : Sets the duration time of screen in the Auto Sequence mode. ➂ Continuous : The Event Monitoring screen remains alive until you press the “Alarm” button in the front to cancel the screen manually.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 5-17 SHR-2040/2041/2042 USER’S MANUAL ● Monitor You are not allowed to connect VGA OUT and Composite/S-Video OUT simultaneously. Consequently, the user is obliged to choose either Composite Output or S-Video Output. ① Composite : Makes the output come out through the “Composite / S-Video OUT” port. ➁ VGA : Makes the output come out through the “VGA Out” port.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 5-18 4 Recording Mode Record Mode ● Details for Record Mode Menu are as follows. NTSC PAL If you press the front “REC” button, the mode value to be recorded will be set. ☛ For the setup of Event Recording Mode value, refer to 5-20. Event Recording Mode Setup Menu. ● Mode On : The current channel is recorded if the REC button is pressed. Off : The current channel is not recorded even thought the REC button is pressed. The default value is set to “On”.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 5-19 SHR-2040/2041/2042 USER’S MANUAL Record Video size Mode ● Video size It sets the video to be recorded. Half D1 : (NTSC) 720x240(N) . Normal (PAL) 720x288(N) . Normal CIF : (NTSC) 352x240(C) . CIF (PAL) 352x288(C) . CIF ● Auto Deletion Press the [Off] button at the bottom of left to select either OFF or On. Select “On” to move to the Date selection button and to limit the search date.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 5-20 5 Event Record Mode ● The detailed items of Event Record Menu are as follows. Event Record Mode setup NTSC PAL ● Event Record Mode setup Sets a mode to be recorded when an event occurs. ● V. Size (Video Size ) Sets the size of a screen to be recorded.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 5-21 SHR-2040/2041/2042 USER’S MANUAL ● Quality Quality will be determined. Select the one among Very High/High/Normal/Low. ● Rate Sets the Rate the number of screen recorded every second. It you set to 15ips, the system records too many screens per second and play continues intermittently since recording is more detailed. This is appropriate for concentrated monitoring zone setup. In case of NTSC, select the one of 30 ips/ 15 ips/ 10 ips/ 7.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:58 PM Page 5-22 Alarm Detection Setup ● ● Off : Sensor does not operate. ① N.O(Normal Open) Sensor : Sensor remains open all the time and if closed, an alarm will be issued. (A Contact) ➁ N.C(Normal Close) Sensor : Sensor remains closed all the time and if open, an alarm will be issued. ( B Contact) Cam Sets a camera that will synchronize with the current sensor. The default value is currently set to the sensor number.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 5-23 SHR-2040/2041/2042 USER’S MANUAL Motion Detection Setup ● Motion Detection Mode Off : Motion Detection does not operate On : Motion Detection operates. ● Area Selects the Motion Detection area. It is composed of 45x40(NTSC)/45x48(PAL) sized Block. It is impossible to set 4 block rows(Up/Down/Left/Right) to allow them to be displayed in all monitors. Select All : Selects the whole area. Select Block : Selects a block every time.
SHR-2040/2041/2042-ENG-1 2005.6.29 ● 4:59 PM Page 5-24 Sensitivity Sets the sensitivity of motion detection. Sensitivity grade consists of Low ➝ Medium ➝ Very High in the ascending order. ● Alarm-Out Sets the Alarm-Out when Motion occurs. 5 Alarm Outs are supported. Select an alarm-out that you want to synchronize with the current motion channel. Multi-selection is possible. ● Beep-Out Sets the Alarm-Out Duration. Alarm-Out continues for the determined duration.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 5-25 SHR-2040/2041/2042 USER’S MANUAL 6 Record Schedule This setup selects a time to record automatically. Selection by the day or by the time is available. The default value is set to “Event Record”. 5-25 ● Press “CH >” copies the value of Channel 1 to all the channels. ● The horizontal axis numbered from 0 to 23 represents the time value. The vertical axis numbered from S to H represents the day value.
SHR-2040/2041/2042-ENG-1 2005.6.29 ● 4:59 PM Page 5-26 Schedule / Event Record On occurrence of Event, Continuous Recording is replaced with Event Recording Mode. ● Holiday If you press “Holiday”, a calendar pops up and you are able to designate holidays. Move to a date and press “Enter” to complete designation. Press “Enter” once more to cancel designation. “H” at the bottom of the table means a holiday.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 5-27 SHR-2040/2041/2042 USER’S MANUAL 7 Backup Backup ● ● ● ● ● ● ● ● ● If there is a device, the free space and the backup device is displayed. Select a date, time, and camera No. to backup, and press “Start”. When you change Start Date/Time or End Date/Time, free space keeps updated in the Free Space zone. A file name is composed of Folder/File Name.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 5-28 8 Network IP Setup ● Connection Mode Designates the kind of the network connected to the main body of SHR-2040/2041/2042. Static IP : When the main body is connected to the network with Static IP. Dynamic IP : When the main body is connected to the network with Dynamic IP supplied by DHCP. ADSL(PPPoE) : When the main body is connected to the ADSL network with PPPoE.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 5-29 SHR-2040/2041/2042 USER’S MANUAL ● IP Sets the IP address for the main body of SHR-2040/2041/2042 to connect with the network. If the Connection Mode is set to Static IP, you shall type in IP yourself. If the connection mode is Dynamic IP or ADSL(PPPoE), the IP allocated by the DHCP server or ADSL company will be automatically displayed. In case of failure of DHCP or ADSL connection, 000.000.000.000 will be displayed.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 5-30 Transfer Protocol Settings ● You may select either TCP or UDP for the protocol type. If you select ADSL from the IP setup page, only TCP is available. While TCP is selected, Audio transmission is not available. ● The available Port(TCP) ranges from 554 to 998 and the port number will be changed by 4. Once the first digit is determined, the following 3 digits will change accordingly.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 5-31 SHR-2040/2041/2042 USER’S MANUAL Callback Settings ● The Callback function is used to forward a callback message to the IP where SmartViewer is in action in case Alarm, Motion Detection, or Video Loss event occurs. ● On/Off : Off is default but you may choose On. ● IP Address : IP setting is available only when On is selected from On/off Setting. Select the IP address of PC where SmartViewer is in action.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 5-32 9 Network Setup Port Setup for SmartViewer Connection ● The Port value for DVR registration of SmartViewer (Setup ➝ Site Setup) shall be as same as that of the set (TCP). ● If you want to use the IP Router, you shall forward the activated Port depending on the current setting value. - If set to TCP, allocate 4 ports to the IP Router whose Port(TCP) was set.
SHR-2040/2041/2042-ENG-1 2005.6.
SHR-2040/2041/2042-ENG-1 2005.6.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 6-1 SHR-2040/2041/2042 USER’S MANUAL 1 PTZ Camera Control Mode ● Select a proper PTZ camera Configuration value in MENU to enter PTZ Control Mode. ● Selected in MENU, the PTZ symbol( ● If you press the Enter( ¦ ) button among direction keys in front of Split Screen, a blue bar will appear in the monitor screen.
SHR-2040/2041/2042-ENG-1 2005.6.29 ● 4:59 PM Page 6-2 Other PTZ Camera Control Modes perform its control in a single screen. Press the channel selection button in the left front to select the PTZ setting channel and press the PTZ button. If you succeed in entering Single Screen PTZ Camera Control Mode, the PTZ symbol on the screen will turn yellow from white while the PTZ button will turn blue.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 6-3 SHR-2040/2041/2042 USER’S MANUAL 2 Basic Operation of PAN, TILT, & ZOOM ● PAN Press the LEFT or RIGHT button in front SHR-2040/2041/2042 in PTZ Camera Control Mode to control PTZ Camera horizontally. PTZ ● TELE WIDE VIEW PRESET TILT Press the UP or DOWN button in front SHR-2040/2041/2042 in PTZ Camera Control Mode to control PTZ Camera vertically.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 6-4 3 Preset Setup ● Records a certain position of PTZ Camera. ● Memorizes up to 20 PTZ Camera positions at the moment. Note For AD Protocol PTZ Camera, this memorizes only 7 Presets. ● Press the Preset button in front of SHR-2040/2041/2042 in Single Screen PTZ Camera Control Mode to set up Preset. PTZ ● TELE WIDE VIEW PRESET After Preset setup, press ENTER.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 6-5 SHR-2040/2041/2042 USER’S MANUAL 6-5 ● Move the cursor to right and press ENTER in PTZ Control Mode first. Then, press the “Enter” to run P/T/Z/ operation mode in the PIP screen and press the “Enter” again to cancel P/T/Z/ Motion Mode. ● Press Enter at the Position Name position to see Virtual Keyboard. Enter the type position name and press the “OK” to save the position and position name.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 6-6 4 Camera Menu Setup ● Camera Menu is a menu supplied by PTZ Camera itself. This Menu sets up several conditions of PTZ Camera. Note Panasonic or Samsung Protocol Camera only is authorized for Camera Menu setup. ● Press the Preset button in front of SHR-2040/2041/2042 in Single Screen PTZ Camera Control Mode to select Camera Menu.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 6-7 SHR-2040/2041/2042 USER’S MANUAL 5 Preset View ● Preset setup allows your movement to a certain saved position of PTZ Camera. ● Press the VIEW button in front of SHR-2040/2041/2042 in Single Screen PTZ Camera Control Mode to select Preset.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 6-8 6 Other View ● Press the “VIEW” button in front of SHR-2040/2041/2042 in Single Screen PTZ Camera Control Mode to supply PTZ Camera. This is a very special function. Note Samsung, Panasonic, PelcoP, or PelcoD Protocol PTZ Camera supports this function.
SHR-2040/2041/2042-ENG-1 2005.6.
SHR-2040/2041/2042-ENG-1 2005.6.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 7-1 SHR-2040/2041/2042 USER’S MANUAL 1 REC (Normal Recording) ● Pressing REC the button starts recording as set in the record mode. Then, REC LED lights on and a recording icon appears on the screen. During the recording in HDD, the front HDD LED blinks. ● During the normal recording, you can stop it by pressing the REC button. If the recording stops, REC LED lights out.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 7-2 2 Schedule Recording ● While “Record Schedule” or “Schedule/Event recording” is selected in the Record Schedule menu, Schedule Recording automatically starts. Otherwise, Schedule Recording remains inactivated. During the Schedule Recording, Recording Icon appears on the screen. During the recording in HDD, the front HDD LED blinks. ● If the Event Recording is selected, the recording starts at the every event.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 7-3 SHR-2040/2041/2042 USER’S MANUAL 3 Event Recording ● Alarm Detection Sensor operation mode in Alarm of Event Record menu shall be set to N.O (Normal Open) or N.C (Normal Close). ● Motion Detection Motion detection in the Event Recording menu shall be set to On. ● Video Loss Detection Video Loss in Event Record menu shall be set to On. ● Event Recording Mode Sets the recording type when an event occurs.
SHR-2040/2041/2042-ENG-1 2005.6.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 8-1 SHR-2040/2041/2042 USER’S MANUAL Before Use ● Pressing the “SEARCH” button shows Search Menu on the screen as seen above. ● Calendar Search searches a video file by the use of a calendar at the desired time. ● Event Search searches a video file recorded by the occurrence of event. ● Date/Time Search searches a video file by the entering of a day and time. ● “Go To First” searches a video file from the oldest one.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 8-2 1 Calendar Search ● Be sure to select both the channel and the date to search. And press the [Start] button to search for the desired time. ● Use a calendar to search the video file of desired time. Four channels in maximum are in the range of search. ● Select the channel up to 4 by the use of ¦, and Enter button. And then the date column will be displayed in thick blue when it has a video recorded in the channel.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 8-3 SHR-2040/2041/2042 USER’S MANUAL 2 Event Search 8-3 ● Searches Normal Recording, Schedule Recording, Alarm Recording, Motion Recording, and V.Loss(Video Loss) Recording by the time. ● You shall select a channel to search to see the event information of the channel. ● On the basis of event information for each channel, the system searches a video file for the event. Only one channel is allowed for video search.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 8-4 3 Date/Time Search ● Use the Day/Time information to search a video file at the time as you desire. Up to 4 channels can be searched at once. ● After you select a channel with the , , [Enter] button, the checkbox on the right of selected event number will be checked. ● Use the button until you reach the Search Time setup line. Press the [Enter] button to change the search time.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 8-5 SHR-2040/2041/2042 USER’S MANUAL 4 Go to First Search 8-5 ● Searches the oldest one among recorded video files. Up to 4 channels can be searched at once. ● After you select a channel with the , , [Enter] button, the checkbox on the right of the selected channel number will be checked. ● Press the [Start] button want to start the search and to cancel. And press the [Cancel] button to cancel the search.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 8-6 5 Go to Last Search ● Searches the latest one among recorded video files. Up to 4 channels can be searched at once. ● After you select a channel with the , ,[Enter] button, the checkbox on the right of the selected channel number will be checked. ● Press the [Start] button want to start the search and to cancel. And press the [Cancel] button to cancel the search.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 8-7 SHR-2040/2041/2042 USER’S MANUAL 6 Backup ● First, select the backup device. ● Mark the data of device. ● Select the file name to backup, and the detail information of a file is displayed in the below. ● The [Previous] button shows the previous page. ● The [Next] button shows the next page. ● The [Start] button plays the desired file. ● The [Exit] button exits the menu. Note SHR-2042 supports the internal CD-R/W.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 8-8 7 Playback II ● Press the PLAY/PAUSE button( ) to play the data recorded in HDD. ● If you used the SEARCH button for playback just before, the system would remember the information of the played channel until you click the PLAY/PAUSE button( II ) again, then the system plays the previous channel. If you press the PLAY/PAUSE button( II ), the Search Menu will appear as far as you never tried the playback.
SHR-2040/2041/2042-ENG-1 2005.6.29 4:59 PM Page 8-9 SHR-2040/2041/2042 USER’S MANUAL ● Definition Play Screen Mode 4 Split Screen Single Screen PIP Screen 6 Split Screen 9 Split Screen ① 4 Split Screen : If you select more than a channel, 4 Split Screen will appear. ➁ Single Screen : This appears when you select one channel in Search. If you press the [CH1~CH4] button in the other split screen, the selected channel appears with the single screen.
SHR-2040/2041/2042-ENG-1 2005.6.29 ● 4:59 PM Page 8-10 Play at Faster Speed If you press the LEFT or RIGHT button( ¦¦ / ) during the playback, you will be able to see the screen at the x2, x4, x8, x16, x32, and x64 speed either forwardly or reversely. ● Viewing Still Screen If you press the LEFT or RIGHT button( ¦¦ / ) when the system paused, you will be able to see still screens forwardly or reversely.
SHR-2040/2041/2042-ENG-2 2005.6.
SHR-2040/2041/2042-ENG-2 2005.6.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-1 SHR-2040/2041/2042 USER’S MANUAL 1 Introduction Smart Viewer is a program that a general PC user is able to install SHR-2040/2041/2042 to his PC to monitor the video and audio data in the real time through network without going to the site where SHR-2040/2041/2042 is installed.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-2 2 Feature ● Thanks to the transmission of video data compressed by the MPEG-4 Video Compression method, it can play the video images of good quality. ● Thanks to the G.726 Voice Compression method, it supplies the voice data of good quality. Use of armored MIC improves the quality of remote voice.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-3 SHR-2040/2041/2042 USER’S MANUAL 3 PC Specification(Recommendation) ● OS : Win98SE, WinMe, Win2000, WinXP ● Recommendation : CPU Pentium 3 1GHz or higher RAM 256 MB or higher VGA RAM 32Mb or higher DirectX 8.1 or higher Note Depending on Recording Rate, Video Size, and user’s PC specification set to SHR-SHR-2040/2041/2042, the number of Smart Viewer playback frame varies. For the detailed specification, refer to Appendix 5.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-4 4 Smart Viewer Installation Smart Viewer Installation ● Put a Smart Viewer Program CD in CD-ROM and open the “Smart Viewer” folder in the CD. ● Run the “Setup.exe” file.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-5 SHR-2040/2041/2042 USER’S MANUAL 9-5 ● Click the “Next” button. ● If you agree with Smart Viewer License, click “Yes”. ● Designate a folder to install Smart Viewer in it and click “Next”.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-6 ● The system proceeds with setup file installation and system setup. ● Installation is complete. Click the “Finish” to terminate the installation.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-7 SHR-2040/2041/2042 USER’S MANUAL 5 Smart Viewer Program Execution ● 9-7 Double-click the Smart Viewer icon in the background screen to run the program.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-8 6 Smart Viewer Initial Screen ● Screen Description 2 1 3 4 6 5 7 8 9 10 11 12 13 14 ! This is the button to enter the Search mode in which you can search and play remote the video file recorded in SHR-2040/2041/2042 and enter the Monitoring mode for real-time video monitoring. @ This button terminates or minimizes the program. # It displays the current date, day, and time.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-9 SHR-2040/2041/2042 USER’S MANUAL 7 Monitoring Mode DVR(SHR-2040/2041/2042) / SITE Connection - Select the name of DVR(SHR-2040/2041/2042) or site for connection and click the connection button. ● Note You can set the name, IP, and password of DVR(SHR-2040/2041/2042) for connection in the Setup mode. Also, the site setup which permits simultaneous connection to multi-DVRs(SHR-2040/2041/2042) is available in the Setup mode.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-10 Note No more than 3 users, one Admin. authorized user and 2 User authorized users are allowed to access SHR-2040/2041/2042 simultaneously.(In the case of multicast, 5 User authorized users are allowable.) Caution Once occupied by 3 users( In the case of multicast, 6 users), SHR-2040/2041/2042 does not permit more connection.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-11 SHR-2040/2041/2042 USER’S MANUAL ● Time Information - As soon as you are connected to SHR-2040/2041/2042, the current date, day, and time of SHR-2040/2041/2042 will be displayed. - Otherwise, the current date, day, and time of your PC will be displayed. ● Connection Information - As soon as you are connected to SHR-2040/2041/2042, the connection button will display connection status.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-12 Note # Clicking the speaker icon turns the audio of channel on or off. : Audio OFF : Audio ON If you turn the audio of a SHR-2040/2041/2042 channel off, “Disable” will be displayed. : Audio Disabled ✴ For the Audio on channel now, use the following audio button to adjust the volume and set the mute.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-13 SHR-2040/2041/2042 USER’S MANUAL ● Event Log Display Window - Click the Log button to activate the log display window. - It displays the event(alarm, user connection, and setup change) occurring at SHR-2040/2041/2042 in the real-time. Note [Event Message] Connecting.. : Trying to connect to SHR-2040/2041/2042. Connected.. : Succeeded connecting to SHR-2040/2041/2042. Connection Failed : Failed in connecting to SHR-2040/2041/2042.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-14 Caution When Time Change, Load Factory Default, Network Change, System Shutdown, or Hdd Format event occurs, Smart Viewer terminates the connection automatically. ● Camera connection Indication Window - Displays the connection condition of DVR and CAMERA in the list. Note [DVR Icon Color] Successfully connected to SHR-2040/2041/2042, the icon turns yellow, otherwise, turns black.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-15 SHR-2040/2041/2042 USER’S MANUAL ● Screen Split Selection Button - Small Sized Single / Single / Quad / Nine-Split Mode Sixteen-Split Mode - You can change the Split Mode of the screen under monitoring. ● Sequence Mode Button - Changes the channel to be played at the preset interval. - The sequence time interval can be set at the Setup Mode?Viewer Setup.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-16 : When monitoring with Quad Mode : When monitoring with Single Mode : Camera Off Note The number in the screen icon indicates the screen position in SmartViewer. : The orange icon indicates the current channel is connected to a camera. : The gray icon indicates the current channel is connected to a camera but not displayed in the screen. : The black icon with a slash indicates the current channel is not connected to any camera.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-17 SHR-2040/2041/2042 USER’S MANUAL ● NEXT Button - Click the NEXT(Mouse Left Button) to see the channel next to the current channel. In Single Mode : 1 ➝ 2 ➝ 3 ➝ 4 ➝ 1 (CH) In Quad Mode : 1,2,3,4 ➝ 1,2,3,4 (CH) In Nine-Split Mode : 1,2,3,4 ➝ 1,2,3,4 (CH) In Sixteen-Split Mode : 1,2,3,4 ➝1,2,3,4 (CH) Note If you connected with multi-DVRs(SHR-2040/2041/2042) through a site, the sequence will operate as follows. - In Single Mode : DVR1:3CH ➝...
SHR-2040/2041/2042-ENG-2 2005.6.29 ● 5:2 PM Page 9-18 FAVORITE Button - If you press FAVORITE, the FAVORITE window will be activated. a a b b c c d d If you click the current FAVORITE, the cameras saved in the current setting value will be displayed in the screen. You may delete the selected FAVORITE or all FAVORITE setting values. You may set up a new FAVORITE number and name. Change FAVORITE at the set intervals. Note - The FAVORITE button is available only when you contact SITE.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-19 SHR-2040/2041/2042 USER’S MANUAL ● Video Recording Button - If you select a channel in the playback and click the “Save” button, the video will be saved in a file format with the extension of *.dvr in a designated folder of your PC. - The name of the directory in which an image will be saved, the file name, and the image save length shall be set up at the Setup Mode ➝ Viewer Setup.
SHR-2040/2041/2042-ENG-2 2005.6.29 ● 5:2 PM Page 9-20 PTZ Camera Control Buttons - Select a channel connected to PTZ Camera to control PTZ related functions. - PAN Left / Right - TILT Up / Down - Diagonal Control - The channel under PTZ control will be displayed in the center of the button. 3 1 2 !@ ZOOM IN / OUT # POWER ZOOM : Click P button to activate POWER ZOOM. - POWER ZOOM is a function to zoom in or zoom out the video screen by clicking the screen.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-21 SHR-2040/2041/2042 USER’S MANUAL ! PRESET - If you press the PRESET button, a window for PRESET setup pops up. a If you click the current PRESET number and a name, the camera will move to its position. b b You can delete the selected or all the PRESET setup values. c c You can set a new PRESET number and name. Note ! The PRESET function is supported to all the cameras. You are allowed to set no more than 20 PRESET items.
SHR-2040/2041/2042-ENG-2 2005.6.29 ● 5:2 PM Page 9-22 Self Menu Setup of PTZ device 1 ! You can set the function menu in the PTZ camera. 1 2 3 ! This is a Menu screen supplied by the camera itself, seen from Viewer. @ Use the / / / button for the movement between menus. # This is a button for the role of Enter. Note The Camera Menu Setup function is supported by Samsung and Panasonic camera only.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-23 SHR-2040/2041/2042 USER’S MANUAL 8 Search Mode ● The initial screen of search mode - The search mode is divided into the remote mode to search and play the SHR-2040/2041/2042 video and the local mode to play *.dvr file saved in the directory designated by your PC. 1 3 4 2 5 6 7 8 10 11 9 12 ! To change to the search mode for the remote control of video recorded in SHR-2040/2041/2042. @ To show the playback video.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-24 ● DVR(SHR-2040/2041/2042) Selection/Change by contacting SITE - Same as “DVR(SHR-2040/2041/2042)/SITE Connection” of the monitoring mode. ● DVR(SHR-2040/2041/2042) Selection/Change by contacting SITE - Select SHR-2040/2041/2042 from the Contact list. - SHR-2040/2041/2042 turns black if contacted with the ADMIN authority and turns gray if contacted with the USER authority. - Without the ADMIN authority, search is not accessible.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-25 SHR-2040/2041/2042 USER’S MANUAL ● Calendar Window - If the video data in on-line SHR-2040/2041/2042 was recorded, the date turns red. - If you click the date in red, the saved video information is displayed. - The currently selected date will be marked with a thick red box. - ¦ : Moves to the previous month. - : Moves to the next month.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-26 @ Backup Button - If not playback(Stop), the video save button performs the backup function. - If the save button is pressed, the window for backup pops up. - Set a Start/End tome for backup and select a file format to save. - The backup starts when the “Start” button is clicked. The backup file is saved according to the setting route; Setup ➞ Viewer Setup ➞ Video Recording ➞ Video Location. - To stop the backup, click the “Stop” button.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-27 SHR-2040/2041/2042 USER’S MANUAL $ Print - This function outputs the screen zone of the playback video which is now being displayed. % Setup Mode Button - This button pops up the setup mode window. ● Play Buttons 2 1 5 9 3 7 4 6 8 ! Play : Play @ Reverse Play : Reverse Play # Stop : Stop $ Fast Forward : Faster Play % Fast Backward : Faster Reverse Play ^ Step Forward : Forward playback per second.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-28 Note During the play(Play/RevPlay/FF/FB), disconnection or change to the both monitoring mode and local mode is not permitted. Click the Stop button first before the change. ● Time Line - Displays the time information of video in SHR-2040/2041/2042 selected on the calendar window. - The normal mode indicates the time information of 24 hours while the Extension mode indicates the time information every 2 hours.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-29 SHR-2040/2041/2042 USER’S MANUAL ● Next Button - Changes the channel as the Next button does in the monitoring mode. Note During the video playback(Play/RevPlay/FF/FB), the channel change is not available. ● Reload Button - Updates the record time information in the calendar window and time line. ● Local Mode - Plays *.dvr file saved in the directory of your PC by the Record function. - You can search and play only one channel.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-30 9 Setup Mode ● Initial Screen 3 1 2 4 ! Button to select items for DVR Setup, Viewer Setup, Site Setup, and S/W Version setup. @ It shows what the selected Setup item can set up in detail. # button to terminate the setup window. $ Button to save the information revised in the setup window, remark the information prior to such a revision, or terminate the setup window.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-31 SHR-2040/2041/2042 USER’S MANUAL ● Setup Item Selection Button - It is used for the selection of each setup item. - It is composed of 4 items- DVR Setup, Viewer Setup, Site Setup, and S/W Version. - DVR Setup: Allows you to change the remote menu setup items of SHR-2040/2041/2042. - Viewer Setup : Allows you to set the various kinds of item concerning the operation of Smart Viewer.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-32 DVR Setup - Click the [DVR Setup] button for DVR Setup. - You can change remotely the setup items of SHR-2040/2041/2042 Menu, being connected with Smart Viewer. - DVR Setup is composed of 5 items; System, Camera/Audio, Monitoring, Recording, and Network. Note - You are authorized with access to DVR Setup in an Admin authority only. only. - The button will not be activated if you are connected to SHR-2040/2041/2042 as a user or unconnected.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-33 SHR-2040/2041/2042 USER’S MANUAL ● Detailed DVR Setup Items ! System - Information Information shows the information on on-line SHR-2040/2041/2042. SHR204X-V1.0.0-20050701080722 Note For the detailed items of DVR Setup, refer to Chapter 5. - Password Sets the password for the control of SHR-2040/2041/2042 Menu or SHR-2040/2041/2042 key input.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-34 Caution System Password shall be composed of numeric only, up to 8 digits. Note - The Delete key and the combination of Ctrl+C or Ctrl+V in the keyboard are not supported at the System Password input. - Use the BACKSPACE key to delete the contents. Note Default System Password is set to 4321. - Date/Time Data/Time is used to set the information of Date, Time, Format, and DST for on-line SHR-2040/2041/2042.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-35 SHR-2040/2041/2042 USER’S MANUAL - Language Language sets the language in which on-line SHR-2040/2041/2042 will be expressed Note The change of language by the system language results in the change of language expression setup of SHR-2040/2041/2042. In short, the language setup of Smart Viewer does not change. Language specification to be supported is subject to change later.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-36 - Remocon (Remote Control Device) Remocon can set the remote control device installed to SHR-2040/2041/2042. Note If you install the remote control device to the main body of SHR-2040/2041/2042 and activate the setup, PTZ control is not available in the Viewer.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-37 SHR-2040/2041/2042 USER’S MANUAL @ Camera - Config. Config. sets Video, Audio On/Off, Camera Title, and Auto Sequence Time for each channel of on-line SHR-2040/2041/2042. Caution - Only English is supported for the title. If you type in and apply the title in your native language, warning message pop sup to ask your retyping. - The title should be composed of no more than 15 digits.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-38 - PTZ device It sets Camera ID, Protocol, Baud Rate, Parity, Data Bit, Stop Bit, and Serial Mode when connecting the dome camera to all the channels. # Monitoring - Monitoring It sets both the event monitoring and OSG display of the live mode.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-39 SHR-2040/2041/2042 USER’S MANUAL $ Recording - Rec. Mode It sets the Video Size, Quality, and Rate values during the recording by the setting the recoding ON/OFF for the related channel in the live mode. NTSC PAL 15 12.5 15 12.5 15 12.5 15 12.5 Note Full D1(L) Video Size does not support 15ips, 10ips (NTSC) / 12.5ips, and 8.33ips(PAL) Rate. - Video size Rec. Sets the Video size.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-40 - Event Rec. It sets the Video Size, Quality, Rate, Pre Alarm, and Post Alarm values to be recorded when an event occurs. NTSC PAL 25 25 25 25 Note Full D1(L) Video Size does not support 15ips, 10ips(NTSC)/12.5ips, and 8.33ips(PAL) Rate.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-41 SHR-2040/2041/2042 USER’S MANUAL - Alarm Rec. It sets the information necessary for the alarm recording. Note More than one camera should be selected to apply the alarm. - Motion Rec. It sets the information necessary for the recording by the motion Detection.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-42 - Video Loss Video Loss sets up the information on how to inform the user of Video Loss of SHR-2040/2041/2042. % Network - Password It sets the password for Admin and User when connecting with SHR-2040/2041/2042 through the network in Smart Viewer. Caution - Network password should be composed of numeric and it can be input up to 8 digits. - If you leave password blank and apply it, a warning message pops up to ask your retyping.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-43 SHR-2040/2041/2042 USER’S MANUAL Note - The Delete key and the combination of Ctrl+C or Ctrl+V in the keyboard are not supported to the network password input. - Use the BACKSPACE key to delete the contents. Note - Default Admin Password is set to 654321. - Default User Password is set to 654321. - IP Settings It sets the network connection method of SHR-2040/2041/2042.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-44 ● Callback - You can set the Callback function of SHR-2040/2041/2042. - In the event of Alarm, Motion Detection, or Video Loss, set the IP address and port of PC where SmartViewer is installed to forward Callback messages. In failure of message forwarding, set the value for retrial. ● Transfer Protocol - You can change the transfer protocol setting value. The protocol supports TCP/IP and UDP(Unicast, Multicast).
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-45 SHR-2040/2041/2042 USER’S MANUAL Note - SHR-2040/2041/2042 uses 4 ports for TCP connection. - The PORT number is flexible and 4 consecutive numbers are grouped for the change ( 554,555,556,557 ➝ 558,559,560,561 ) - If you use the IP Router for network composition, you should allocate a protocol for SHR-2040/2041/2042. Viewer Setup - Click the [Viewer Setup] for Viewer Setup.
SHR-2040/2041/2042-ENG-2 2005.6.29 ● 5:2 PM Page 9-46 Video Recording ! Naming - Being connected to SHR-2040/2041/2042 in the monitoring or search mode, you can save the video displayed with *.dvr file and name it. - If you set to “Camera No. + Serial No.”, the file name depends on the camera number and serial number. If set to “Camera No. + Date”, it depends on the camera number, current date, and time.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-47 SHR-2040/2041/2042 USER’S MANUAL ● Sequence Time - When connecting with SHR-2040/2041/2042 in the monitoring mode, set the auto sequence time if the auto sequence is set. The time can be set from 10 to 20 minutes. ● OSD Display - Sets if OSD shall be displayed on each channel of Smart Viewer. - Whether you check “Enable” or not, OSD will appear or not.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-48 Site Setup - Click the [Site Setup] button for Site Setup. - The information of DVR(SHR-2040/2041/2042) or Site that you want to connect by Smart Viewer is set in the Site Setup. - Smart Viewer allows you to connect with DVR(SHR-2040/2041/2042) or Site registered only here. 1 3 5 2 4 ! The DVR(SHR-2040/2041/2042) list that registered by the user is displayed.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-49 SHR-2040/2041/2042 USER’S MANUAL ● DVR List - The information of DVR(SHR-2040/2041/2042) that you want to connect by Smart Viewer is set in the DVR List. - You can register a new DVR(SHR-2040/2041/2042) or delete and edit the DVR(SHR-2040/2041/2042) selected from the registered list, and the name and IP / MAC Address of the registered DVR(SHR-2040/2041/2042) is displayed in DVR List.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-50 ! To add a new DVR(SHR-2040/2041/2042) - If you press the [New] button, the following window will pop up where you are able to add a new DVR(SHR-2040/2041/2042) information. 1. Network Modes - LAN - If DVR(SHR-2040/2041/2042) is connected to the LAN, set the network mode to LAN. - If the LAN connected to DVR(SHR-2040/2041/2042) uses Static IP, select Static IP in the Address Type and input the name and IP address of DVR(SHR-2040/2041/2042).
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-51 SHR-2040/2041/2042 USER’S MANUAL 2.Network Modes - ADSL - If DVR(SHR-2040/2041/2042) is connected to the ADSL, set the network mode to ADSL. - If the ADSL connected to DVR(SHR-2040/2041/2042) uses Static IP, select Static IP in the Address Type and input the name and IP Address of DVR(SHR-2040/2041/2042). - You should select a PORT in accordance with the PORT number set at the DVR(SHR-2040/2041/2042) network menu.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-52 Note - The MAC address of DVR is written at the side label of the product. It is also found in the system information of DVR Menu. - If the DVR(SHR-2040/2041/2042) is connected to ADSL, the network bandwidth is low. Therefore, the transfer rate becomes low and the viewer operates in the more limited range. - The viewer can monitor up to 4CH all the same time. - The viewer can search or play only 1CH. - The audio does not play.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-53 SHR-2040/2041/2042 USER’S MANUAL # To Edit the old DVR(SHR-2040/2041/2042) - If you select a DVR(SHR-2040/2041/2042) in the DVR list to edit and press the [Edit] button, the following message box pops up. Press [OK] button to edit the DVR(SHR-2040/2041/2042). - When the DVR(SHR-2040/2041/2042) to edit is connected with the Smart Viewer, the following message box pops up and the DVR(SHR-2040/2041/2042) cannot be edited.
SHR-2040/2041/2042-ENG-2 2005.6.29 ● 5:2 PM Page 9-54 Site List - You can register and control the many DVRs(SHR-2040/2041/2042) to be connected with the smart viewer at once with a site in the site list. You are allowed to register a new site ,and delete or edit the selected site in the registered list. Also, you can add or delete a DVR(SHR-2040/2041/2042) to the site selected in the site list.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-55 SHR-2040/2041/2042 USER’S MANUAL @ To delete an old site or DVR(SHR-2040/2041/2042) - If you select a site or DVR(SHR-2040/2041/2042) in the site list for deletion and press the [Delete] button, the following message box pops up. Press the [OK] button to delete either site or DVR(SHR-2040/2041/2042). - When deleting the DVR(SHR-2040/2041/2042), it is deleted from the site composition but the DVR(SHR-2040/2041/2042) information is not deleted.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-56 - When the site to edit is connected with the Smart Viewer, the following message box pops up and the site cannot be edited. Be sure to cut the connection between the DVR(SHR-2040/2041/2042) and the Smart Viewer before you edit it. - If you select a DVR(SHR-2040/2041/2042) and press the [Edit] button, the following message box pops up and the DVR(SHR-2040/2041/2042) cannot be edited. To edit the DVR(SHR-2040/2041/2042), go to the DVR list.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-57 SHR-2040/2041/2042 USER’S MANUAL S/W Version - If you press the [S/W Version] button, the smart viewer version, system requirements, and the version of DVR(SHR-2040/2041/2042) System S/W, being connected to the smart viewer, are displayed. - You can upgrade the on-line DVR(SHR-2040/2041/2042) System S/W remotely. You are authorized with S/W upgrade in an Admin authority only.
SHR-2040/2041/2042-ENG-2 2005.6.29 ● 5:2 PM Page 9-58 Smart Viewer Version - Smart Viewer Version and system requirements are displayed. ● DVR Version SHR-2040/2041/2042 - DVR Version not only displays the connected DVR(SHR-2040/2041/2042) name if any DVR(SHR-2040/2041/2042) is being connected with Smart Viewer or the name of DVR(SHR-2040/2041/2042) composing a site if any DVR(SHR-2040/2041/2042) is being connected with the site but also displays DVR(SHR-2040/2041/2042) S/W version.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 9-59 SHR-2040/2041/2042 USER’S MANUAL @ Click the following button to open the “SHR-2040/2041/2042 Firmware” file in format. 2040/2041/2042 2040/2041/2042 # Press the [Upgrade] button to transmit a file to the selected DVR(SHR2040/2041/2042) and start the upgrade of DVR(SHR-2040/2041/2042) S/W. $ The progress of file transmission and upgrade is displayed at the bottom.
SHR-2040/2041/2042-ENG-2 2005.6.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 10-1 SHR-4160N/P USER’S MANUAL 1 Product Specification Item Details CPU Memory OS Broadcasting Input Voltage Power Consumption Video Input Video Video Output Audio Input Audio Audio Output 2040 : 30Watt, 2041 : 60Watt, 2042 : 51Watt Composite 16 Channel - 1.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 10-2 Item Details Compression Method Video Size & Performance Remarks Video : MPEG4 Audio : ADPCM Resolution Quality Level Max Image Rate CIF(C) 352X240(NTSC) /352X288(PAL) Very High High Standard Low 15ips(NTSC)/ 25(PAL) Half D1(N) 720X288(NTSC) /720X288(PAL) Very High High Standard Low 15ips(NTSC)/ 12.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 10-3 SHR-2040/2041/2042 USER’S MANUAL Item Search Mode Play Back Video size & Performance Display Mode Play Mode Backup Alarm Network Serial I/F PC Spec. Remote Viewer Support OS Function Backup Viewer PC Spec. Support OS Function Operation Temp. Preservation Temp.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 10-4 2 The specification of HDD and peripheral device ● Internal ATA HDD/IEEE1394/USB HDD I/F External HDD Maker RPM Samsung 5,400 Maxtor 7,200 7,200 5,400 Western Digital 7,200 ● 120 GB 160 GB 120 GB 160 GB 250 GB 120 GB 160 GB Interface Buffer Series Name Model No Remark SV12.
SHR-2040/2041/2042-ENG-2 2005.6.
SHR-2040/2041/2042-ENG-2 2005.6.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 10-7 SHR-2040/2041/2042 USER’S MANUAL 4 Factory Default This restores the Network information and preset values in SHR-2040/2041/2042 to the original state at the time of factory shipment. Factory Default will be done as follows; - Use System / Load Factory Default in MENU or, - If you hold on to the Mode button in Live Mode and keep pressing the CH5 button for 5 seconds, the system will return to the Factory default condition.
SHR-2040/2041/2042-ENG-2 2005.6.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 10-9 SHR-2040/2041/2042 USER’S MANUAL 5 SHR-2040/2041/2042 Smart Viewer Frame Specification for the Playback NTSC FRAME RATE 15 10 7.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 10-10 PAL FRAME RATE 12.5 8.33 6.25 5 2.5 1 Viewer Screen Split Mode VIDEO SIZE Half D1(N) CIF (C) Nine-split 1 frame/sec 12.5 frame/sec Fore-split 12.5 frame/sec 12.5 frame/sec Single 12.5 frame/sec 12.5 frame/sec Half D1(N) CIF (C) Nine-split 8.33 frame/sec 8.33 frame/sec Fore-split 8.33 frame/sec 8.33 frame/sec Single 8.33 frame/sec 8.33 frame/sec Half D1(N) CIF (C) Nine-split 6.25 frame/sec 6.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 10-11 SHR-2040/2041/2042 USER’S MANUAL 6 Troubleshooting(FAQ) 1. The system power is dead and LED in front of the system does not operate at all. - Please check the power connection. - Check the power voltage. - If all your efforts like above end up with nothing, check or exchange the power supply. 2. Video data remains in the system but some channels displays no video data but turns all blue. - Check the image of the camera connected to the system.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 10-12 7. The channel button does not operate in Live. - If the current screen is Event Monitoring, the channel button does not operate. Then, press the Alarm button to terminate the current screen and select a channel. 8. The cursor cannot reach Start during Calendar Search. - Please check both the channel and the date for play are left checked. Both shall be checked for play with Start. The cursor cannot reach the unrecorded date. 9.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 10-13 SHR-2040/2041/2042 USER’S MANUAL 13. Smart Viewer in operation is disconnected. - If you change time, network setup, HDD format, Default Setup, or HDD attachment or detachment for SHR-2040/2041/2042 DVR, the current Smart Viewer will be automatically disconnected. - Check network connection. Smart Viewer, if disconnected from Network, will try reconnection up to 5 times.
SHR-2040/2041/2042-ENG-1 2005.6.
SHR-2040/2041/2042-ENG-1 2005.6.
SHR-2040/2041/2042-ENG-1 2005.6.
SHR-2040/2041/2042-ENG-2 2005.6.29 5:2 PM Page 10-14 Correct Disposal of This Product (Waste Electrical & Electronic Equipment) (Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life.
