Replacement Part List

ManualsBrandsSaltDogg ManualsOutdoor Power Equipment8 cu. ft. Tailgate Salt Spreader

Installation Instructions

TGS01B Salt Spreader

—continued inside

WARNING

Observe the following Safety Precautions before, during

and after operating this spreader. By following these pre-

cautions and common sense, possible injury to persons

and potential damage to this machine may be avoided.

SPREADER WARRANTY INFORMATION

This warranty replaces all previous warranties and no

employee of this company is authorized to extend addi-

tional warranties, or agreements, or implications not

explicitly covered herein.

Buyers Products Company warrants all parts of the

product to be free from defects in material and workman-

ship for a period of one (1) year. Parts must be properly

installed and used under normal conditions. Normal wear

is excluded.

Any part, which has been altered, including modifica-

tions, misuse, accident, or lack of maintenance will not

be considered under this warranty.

The sole responsibility of Buyers Products Company

under this warranty is limited to repairing or replacing any

part(s), which are returned, prepaid, 30 days after such

defect is discovered, and returned part(s) are found to be

defective by Buyers Products Company.

Authorization from Buyers Products Company must

be obtained before returning any part. The following

information must accompany defective parts returned

to Buyers Products Company: RMA #, spreader model,

serial number, date installed, and distributor from whom

purchased.

Buyers Products Company shall not be liable for damage

arising out of failure of any unit to operate properly, or

failure, or delay in work, or for any consequential dam-

ages. No charges for transportation or labor performed

on any part will be allowed under this warranty.

Safety Precautions

1. Read this entire Owners Manual before operating

this spreader.

2. Read all safety decals on the spreader before

operating.

3. Verify that all personnel are clear of the spreader

spray area before starting or operating this spreader.

4. Do not adjust, clean, lubricate or unclog material

jambs without first turning off the spreader.

5. Make sure the spreader is securely fastened to the

vehicle in accordance with this manual.

6. Do not operate a spreader that is in need of main-

tenance or repairs.

7. Always disconnect the battery before removing or

replacing electrical components.

Spreader Assembly

Check contents of box against parts list to make sure

all components are included. When ordering replace-

ment or spare parts refer to parts list (fig. 3) for part

numbers.

Installation (fig. 1)

1. Locate and mark center of tailgate.

2. Assembly Angles (24) and Braces (23) as shown in

Fig.1 Use 3/8" carriage bolts, flat washers and nuts.

Do not tighten fasteners at this moment.

3. Center assembly on top of tailgate. Lower angle

must be flush with top and inside surfaces of tailgate.

9049 Tyler Blvd. • Mentor, Ohio 44060

Phone (440) 974-8888 • Fax (440) 974-0165

Toll-Free Fax 800-841-8003 • saltdogg.com

Summary of content (4 pages)

PAGE 1
9049 Tyler Blvd. • Mentor, Ohio 44060 Phone (440) 974-8888 • Fax (440) 974-0165 Toll-Free Fax 800-841-8003 • saltdogg.com Installation Instructions TGS01B Salt Spreader Safety Precautions WARNING Observe the following Safety Precautions before, during and after operating this spreader. By following these precautions and common sense, possible injury to persons and potential damage to this machine may be avoided. 1. Read this entire Owners Manual before operating this spreader. 2.
PAGE 2
Electrical Installation (fig. 2) 4. Position braces (23) on top of side rails. Using holes in braces as guides mark and drill holes for 3/8" screws. 5. Attach braces to side rails using 3/8" screws, flat washers and nuts. 6. Center spreader assembly on top of rear bumper and align with Angle (24). 7. Attach Mounting Angles (22) to spreader frame. 8. Make sure spreader frame is vertical. Using holes in Angle (24), mark and drill holes for 3/8" screws in Mounting Angle (22). 9.
PAGE 3
001379 Fig. 2 BATTERY POSITIVE CB50PB BATTERY NEGATIVE 3035934 3008620 3011864 Observe spinner direction of rotation. The correct direction is counter clock wise when looking inside hopper from the top. If direction is clock wise reverse wires between Motor and Wire Harness. 2. Make sure lid is installed and latches are secured when spreader is in use. 3. Do not leave material in hopper between uses. 4. Do not drive with material in hopper. 5. Always clean/wash hopper at the end of the day. 6.
PAGE 4
9049 Tyler Blvd. • Mentor, Ohio 44060 Phone (440) 974-8888 • Fax (440) 974-0165 Toll-Free Fax 800-841-8003 • saltdogg.com Fig. 3 Bill of Materials 3 17 14 16 2 ITEM PART NO. QTY.