Installation Guide

ManualsBrandsSalsbury Industries ManualsKitchen72000 Series 12 in. W x 78 in. H x 12 in. D Double Tier Vented Metal Locker Assembled in Gray

Vented Lockers – 72000 Series

Double Tier Installation Instructions

Thank you for selecting Salsbury’s vented double tier lockers. We are confident that the quality and construction of the lockers will prove to be a

good investment. These instructions are intended to assist you in assembling the lockers. The lockers should then be placed in the installed

location and anchored to the floor, wall, or to both. Individual job conditions will dictate the type of anchor fasteners.

Preliminary Note

Please read the complete assembly instructions before attempting to

assemble the lockers. Check the materials to be sure that they are

correct for the job and that there is no damage.

Be careful to use the correct hardware. Use screw no. 1 all around

with screw heads out, except where noted. Lockers should be

assembled in groups as indicated in the order of the drawings.

The essential tools required for assembling the lockers are a 5/16”

nut driver and 2 small nail punches or drift pins for hole alignment.

The lockers should be assembled on a flat level surface and installed

in position, anchoring to the floor or wall, as required.

See the illustration to the right to identify the locker parts. Note that

the sloping hood, front base, end base, and name plate are optional

items and their assembly is covered by a separate installation

instruction.

Assembly

1. Fasten a top, bottom, and side to a back. The top and bottom are

identical parts and should have the flanges down. Insert a rear leg

and fasten. See Illustration 1.

2. Fasten another top in the center with the flanges down and the

tapered end flanges in front. See Illustration 2.

For a one-wide locker, skip to Step 4.

Illustration 1

Parts Identification

Illustration 2

SALSBURY INDUSTRIES

1010 East 62

Street, Los Angeles, CA 90001-1598

Phone: 1-800-562-5377 Int’l Phone: 323-846-6700

Fax: 1-800-562-5399 Int’l Fax: 323-846-6800

Installation instructions are provided as general guidelines. It is advised that a professional installer be consulted. Salsbury Industries assumes no product assembly or installation liability.

Summary of content (4 pages)

PAGE 1
Vented Lockers – 72000 Series Double Tier Installation Instructions Thank you for selecting Salsbury’s vented double tier lockers. We are confident that the quality and construction of the lockers will prove to be a good investment. These instructions are intended to assist you in assembling the lockers. The lockers should then be placed in the installed location and anchored to the floor, wall, or to both. Individual job conditions will dictate the type of anchor fasteners.
PAGE 2
Vented Lockers – 72000 Series Double Tier Installation Instructions Assembly (continued) 3. Position additional sides, backs, tops, and bottoms and fasten in place. See Illustration 3. 6. Fasten the last door and frame assembly into place, ensuring that they are all fastened correctly. See Illustration 6. 4. Add a last side (flange in) and the other leg. See Illustration 4. 7. Finally, install coat hooks below the top and lock hole fillers into the doors.
PAGE 3
Vented Lockers – 72000 Series Installation Instructions - Options Thank you for selecting Salsbury’s vented double tier lockers. We are confident that the quality and construction of the lockers will prove to be a good investment. These instructions are intended to assist you in assembling option items into the locker. The name plates, front bases, end bases, and sloping hoods are each separate option items and may or may not be included in your order.
PAGE 4
Vented Lockers – Locker Benches Assembly & Installation Instructions Thank you for selecting Salsbury’s 77770 series locker aluminum benches. We are confident that the quality and construction of this product will provide years of maintenance free use. Preliminary Notes Assembly There are two basic steps to assembly and installation: 1. The bench pedestals must be assembled to the bench top. 2. The bench assembly must be bolted to the floor.