Instructions / Assembly

ManualsBrandsSalsbury Industries ManualsLockers54000 Series 12 Compartments Four Tier 45 In. W x 78 In. H x 18 In. D Metal Locker Assembled in Gray

Extra Wide Standard Lockers – 54000 Series

Four Tier Installation Instructions

Phone: 1-800-562-5377 Int’l Phone: 323-846-6700

Fax: 1-800-562-5399 Int’l Fax: 323-846-6800

www.lockers.com engineering@lockers.com

Installation instructions are provided as general guidelines. It is advised that a professional installer be consulted. Salsbury Industries assumes no product assembly or installation liability.

SALSBURY INDUSTRIES

1010 East 62

Street, Los Angeles, CA 90001-1598

Thank you for selecting Salsbury’s extra wide standard four tier lockers. These instructions are intended to assist you in assembling the lockers. Assembly of the various locker

components will be with #10 - 24 x 3/8” long slot less screws and #10 nuts (provided). Loosely fasten a screw and a nut into every set of mating holes with the screw heads positioned on

the outside of the locker or on the exposed surface.

One Wide Locker Assembly

Step 1: Attach the top shelf and bottom shelf to the back panel.

Step 2: Turn the back panel on its back with the shelves pointing upward. Attach the

first side panel, the left rear leg, and three compartment dividers to the assembly from

Step 1.

Step 3: Attach the second side panel and the right rear leg to the assembly of Step 2.

The locker chassis is now complete.

Step 4: Attach the pre-assembled door frame onto the assembly of Step 3.

Step 5: Tighten all fasteners checking for squareness of the locker while tightening.

Attach optional sloping hood, end bases or front base (see pages 4 and 5).

Step 6: Place the locker in the installed location and anchor to the floor, wall, or to

both. Individual job conditions will dictate the type of fastening anchors to use (not

provided).

Step 7: Fasten all lockers in a row together by installing fasteners provided through

the side panels. Installation is now complete.

Summary of content (5 pages)

PAGE 1
Extra Wide Standard Lockers – 54000 Series Four Tier Installation Instructions Thank you for selecting Salsbury’s extra wide standard four tier lockers. These instructions are intended to assist you in assembling the lockers. Assembly of the various locker components will be with #10 - 24 x 3/8” long slot less screws and #10 nuts (provided). Loosely fasten a screw and a nut into every set of mating holes with the screw heads positioned on the outside of the locker or on the exposed surface.
PAGE 2
Extra Wide Standard Lockers – 54000 Series Four Tier Installation Instructions Three Wide Locker Assembly Step 3: Attach the second top shelf and the second bottom shelf to the second back panel Step 1: Attach the top shelf and bottom shelf to the back panel. Step 4: Simultaneously attach the assembly of Step 3 (second Step 1 assembly), the as in Step 1. second side panel, and three additional compartment dividers to the assembly of Step 2.
PAGE 3
Extra Wide Standard Lockers – 54000 Series Four Tier Installation Instructions Three Wide Locker Assembly (continued) Step 8: Position the pre-assembled door frames onto the assembly of Step 7 then fasten one by one. Step 7: Attach the last side panel and the right rear leg to the assembly of Step 6. The locker chassis is now complete. Step 9: Tighten all fasteners checking for squareness of the locker while tightening. Attach optional sloping hoods, end bases or front bases (see pages 4 and 5).
PAGE 4
Extra Wide Standard Lockers – 54000 Series Four Tier Installation Instructions Sloping Hood Installation (Optional) Step 1: Assemble the top panel to the rear panel with #10 - 24 x 3/8” slot less screws and #10 nuts (provided). Position the flange of the top panel behind the rear panel. Step 3: Attach the sloping hood to the top of the locker with #10 - 24 x 3/8” slot less screws and #10 nuts (provided).
PAGE 5
Extra Wide Standard Lockers – 54000 Series Four Tier Installation Instructions Front Base Installation (Optional) End Base Installation (Optional) Position the front base between the front legs of the locker with the flange upward. Assemble to the locker with #10 - 24 x 3/8” slot less screws and #10 nuts (provided). Position the appropriate end base (right or left) behind the corresponding side legs (right or left) of the locker with the flange upward.