PLANO 100 MEDIUM Installation Manual Manual De Instalación Manuel d’Installation 23 - 42” 100 LBS (45 KG)
IMPORTANT SAFETY INSTRUCTIONS • Carefully inspect the mount for shipping damage or missing parts. If any damage is apparent or you are missing parts contact Salamander Designs at 800-535-5659. • Read ALL assembly instructions before assembly. If you have any questions, please contact your installation contractor or Salamander Designs. • Mounts must be attached as specified in assembly instructions. Improper installation can result in serious personal injury.
TOOLS PLANO 100 Tools Required for Assembly: MEDIUM Pencil Level Unpacking Unpack all content and check to ensure that all of the parts are in proper condition. To help protect the environment, use the appropriate recycling and discarding methods for the packaging items. The boxes used for the packaging of this product may be recycled or re-used. Desembalaje Drill and Bit: 3/16” (4.
HARDWARE B - 6X Lag Screw M7 x 60 A - 1X Allen Key M6 D - 4X Washer M5 E - 12X Washer M8 C - 6X Plastic Wall Plug 10 x 50 G - 6X Flat Head M8 x 16 F - 4X Spacers M4 / M5 H - 6X Hex Nut - M8 M6 / M8 K - 1X Allen Key J - 4X - Mounting Screws M2.
PA R T S I - 1X - Wall Bracket IV - 1X Pad Lock II - 2X - TV Bracket III - 2X - Extension Wing III I II 5
1. Install Wall Bracket 3-15/16’’ 100 mm A B EN G For wood constructions, locate a framing stud at the desired location using a stud finder device. Align and level the Wall Bracket (I) with the framing stud. Using a pencil mark top and bottom holes as shown. Note: It is important to utlize one of the three center holes when installing onto wood framing. ESP Para construcción de madera localice un derecho en la ubicación deseada utilizando un aparato para encontrar pie derecho.
C D Predrill mounting holes 2.5” (64 mm) deep using a 3/16” (4.5 mm) bit for wood construction; 3/8” (10 mm) bit for masonry construction. Install Lag Screws (B) with Washers (E), through Wall Bracket (I), level and tighten firmly with Allen Key (A). For Masonry Installation use Plastic Wall Plugs (C). Taladre agujeros de montaje de 64 mm (2.5”) de profundidad utilizando una broca de 4.5 mm (3/16”) para construcciones de madera o una broca de 10 mm (3/8”) para construcciones de mampostería.
2. Attach TV Brackets A EN G ESP FRA 8 Align TV brackets (II) with FOUR TV mounting holes. Attach using the supplied Mounting Screws (J). To determine the correct thread size and length, refer to TV manufacturer installation manual. NOTE: Washers (D) are necessary when using M4 and M5 mounting screws. Spacers (F) can be utilized in applications where interferences at back of TV prevent proper fit of TV Bracket (II). NOTE: It is always necessary to fasten TV at four points for proper installation.
B If TV mounting pattern exceeds 13” (330 mm) in width or 8-1/2” (216 mm) in height, use supplied Extension Wings (III) to expand mounting. Extension Wings (III) are fastened to TV Brackets (II) using Flat Heads (G), Washers (E), and Hex Nuts (H) prior to mounting to TV. Attach using the supplied Mounting Screws (J) and optional Spacers (F). NOTE: It is always necessary to fasten TV at four points for proper installation.
3. EEN NG ES ESP P FRA 10 Install TV to Wall Bracket A B C Pull on black cord to unlock Click Fasteners and hook TV Brackets (II) onto Wall Bracket (I) from top. Center TV Brackets (II) on Wall Bracket (I) and push black Click Fasteners up into lock position. Install Pad Lock (IV). Jale la cuerda negra para soltar los Sujetadores “Clic” y enganche los Soportes de TV (II) al Soporte de Pared (I) desde arriba.
SALAMANDER DESIGNS LIMITED WARRANTY GARANTÍA LIMITADA DE SALMANDER DESIGNS GARANTIE LIMITÉE DE SALAMADER DESIGNS Salamander Designs Ltd. (Salamander) provides the following Limited Warranty. The Limited Warranties herein described for the specific products listed below shall be in lieu of any other warranty, expressed or implied, including but not limited to any implied warranty of merchantability or fitness for a particular use.
www.SalamanderDesigns.com ©2008 Salamander Designs Ltd. Doc #503-002 v4.