Installation Guide

Sakrete.com • 866-725-7383
The Pro’s Choice Since 1936
Application:
1. Load the cartridge assembly into a standard caulking gun.
2. Unscrew the cartridge cap and remove the nozzle plug.
3. Attach the static mixer nozzle. Dispense mixed paste onto work surface.
4. Use the mixed paste within 5 minutes.
Curing:
1. Within 1 - 2 hours of mixing and applying, Rapid Setting Anchoring Epoxy can
be drilled, filed, tapped, and sanded. Cure time to ultimate hardness is 24
hours.
2. Actual cure time is affected by temperature and product amount used: higher
temperatures and larger volumes of material used cure faster.
Precautions:
Minimum temperatures should be 40°F (4°C) with no rain in the forecast within
24 hours of application. For applications outside temperatures and conditions,
contact Sakrete Technical Service.
• Does not adhere to PTFE, polyethylene, or polypropylene.
• Not intended for use in structural applications.
NOTE: Proper application and installation of all Sakrete products are the responsibility of the end user.
Safety:
READ and UNDERSTAND the Safety Data Sheet (SDS) before using this product.
WARNING: Wear protective clothing and equipment. For emergency information,
call CHEMTREC at 800-424-9300 or 703-527-3887 (outside USA).
KEEP OUT OF REACH OF CHILDREN.
Limited Product Warranty:
The manufacturer warrants that this product shall be of merchantable quality
when used or applied in accordance with the manufacturer’s instructions. This
product is not warranted as suitable for any purpose other than the general
purpose for which it is intended. This warranty runs for one (1) year from the
dates the product is purchased. ANY IMPLIED WARRANTY OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED TO
THE DURATION OF THIS WARRANTY. Liability under this warranty is limited to
replacement or defective products or, at the manufacturer’s option, refund of the
purchase price. CONSEQUENTIAL AND INCIDENTAL DAMAGES ARE NOT RECOV-
ERABLE UNDER THIS WARRANTY.
Rapid Setting anchoring epoxy
Sakrete
®
Fast Setting Anchoring Epoxy is a two-com-
ponent epoxy compound used to anchor bolts or other
metal objects in concrete and masonry. A rapid setting
material that can be used in vertical or horizontal ap-
plications. Its rapid set allows for use in walls and with
minimal run-out.
Features:
• Sets within 5 minutes
• Excellent thread lock
• Exceptionally strong and hard once cured
• Solvent-free with no volatile components
• Will not shrink upon curing
• Ready to use
Use For:
• Adhesive or sealing applications
• Anchoring machines
• Seals leaks
• Fills holes, pits and cracks
Technical Data:
Compressive Strength - 8,500 psi (57 MPa)
Compressive Modulus - 275,000 psi (1.9 GPa)
Color:
Gray
Preparation:
1. To achieve optimum performance, surfaces and holes should be
dust-free and cleaned of all surface contaminants, such as grease, oil, water,
or dirt.
2. Scuffing, wire brushing, or sanding the surface prior to cleaning helps insure
a good bond. Care should be taken to remove all loose debris from the drilled
hole using a suitable blower or vacuum before applying.
SAKRETE
®
and the background design are registered trademarks of SAKRETE of North America LLC, Charlotte, NC 28217 • ©2006. SAKRETE
®
is manufactured under license from SAKRETE of North America LLC.
For current and complete product information, contact SAKRETE Technical Services toll-free at 866-725-7383 or visit Sakrete.com.
Rev. 06/16
Uncured Properties Results
Form Two-part paste
Non-volatile content 100%
Density 10.8 lb/gal (1.3 g/cm
3
)
Mix ratio, base to curing agent 1:1
Work life at 75
O
F (24
O
C) 20 gm mass: 5 min.
Thin film: 60 min.