Return to Main Menu PARAMETER LIST ALARM LIST M-CODE LIST for MAZATROL MATRIX MANUAL No. : H740HA0030E Serial No. : Before using this machine and equipment, fully understand the contents of this manual to ensure proper operation. Should any questions arise, please ask the nearest Technical Center or Technology Center. IMPORTANT NOTICE 1. Be sure to observe the safety precautions described in this manual and the contents of the safety plates on the machine and equipment.
Return to Library Notes:
Return to Library
Return to Library
Return to Library SAFETY PRECAUTIONS SAFETY PRECAUTIONS Preface Safety precautions relating to the CNC unit (in the remainder of this manual, referred to simply as the NC unit) that is provided in this machine are explained below. Not only the persons who create programs, but also those who operate the machine must thoroughly understand the contents of this manual to ensure safe operation of the machine.
Return to Library SAFETY PRECAUTIONS Basics ! After turning power on, keep hands away from the keys, buttons, or switches of the operating panel until an initial display has been made. WARNING ! Before proceeding to the next operations, fully check that correct data has been entered and/or set. If the operator performs operations without being aware of data errors, unexpected operation of the machine will result.
Return to Library SAFETY PRECAUTIONS Programming WARNING ! Fully check that the settings of the coordinate systems are correct. Even if the designated program data is correct, errors in the system settings may cause the machine to operate in unexpected places and the workpiece to abruptly move out from the machine in the event of contact with the tool.
Return to Library SAFETY PRECAUTIONS ! For the machines of INTEGREX e-Series, programmed coordinates can be rotated using an index unit of the MAZATROL program and a G68 command (coordinate rotate command) of the EIA program. However, for example, when the B-axis is rotated through 180 degrees around the Y-axis to implement machining with the turning spindle No.
Return to Library SAFETY PRECAUTIONS Operations WARNING ! Single-block, feed hold, and override functions can be made invalid using system variables #3003 and #3004. Execution of this means the important modification that makes the corresponding operations invalid. Before using these variables, therefore, give thorough notification to related persons. Also, the operator must check the settings of the system variables before starting the above operations.
Return to Library OPERATIONAL WARRANTY FOR THE NC UNIT OPERATIONAL WARRANTY FOR THE NC UNIT The warranty of the manufacturer does not cover any trouble arising if the NC unit is used for its non-intended purpose. Take notice of this when operating the unit. Examples of the trouble arising if the NC unit is used for its non-intended purpose are listed below. 1. Trouble associated with and caused by the use of any commercially available software products (including user-created ones) 2.
Return to Library CONTENTS Page 1 INTRODUCTION .................................................................................. 1-1 2 PARAMETER ....................................................................................... 2-1 2-1 Outline ................................................................................................................2-1 2-1-1 Types of parameters...............................................................................................
Return to Library 3 2-3-14 Machine parameter ANOTHER (S) .................................................................. 2-296 2-3-15 Machine parameter SPINDLE (SA).................................................................. 2-302 2-3-16 Machine parameter BARRIER (BA) ................................................................. 2-319 2-3-17 Data I/O parameter CMT parameter (CMT) .....................................................
Return to Library INTRODUCTION 1 1 INTRODUCTION This manual describes the meaning and setting of various parameters, and the meaning and elimination procedure of various alarms used for the MAZATROL MATRIX System. This document also gives the list of M-codes. For detailed description of the MAZATROL MATRIX System, refer to the Operating Manual of the machine.
Return to Library 1 INTRODUCTION - NOTE - 1-2 E
Return to Library PARAMETER 2 2-1 2 PARAMETER Outline 1. Scope of this chapter This chapter describes the parameters you can change as required. How to read the list is described in the beginning. Always refer to this list to change parameters. 2. Precautions on this chapter This chapter also gives parameters relating to optional functions. Accordingly, the list includes parameters which cannot be changed. Check the type of machine purchased by you and its specifications before you read the list.
Return to Library 2 PARAMETER 2-1-2 Precautions 1. Details of the parameters may differ according to the machine used, the presence/absence of an option(s), the production time of the NC machines and equipment, etc. Therefore, do not use the parameters of other machines. 2. The parameter list is supplied in the form of data sheets within the NC electronic cabinet at shipment of the machines. Be careful not to lose the list. 3.
Return to Library PARAMETER 2-2 2 Parameter List 2-2-1 User parameter 1.
Return to Library 2 PARAMETER Address (bit) Outline D25 Boring-bar tip relief D26 Returning distance from hole bottom for boring or back-boring D27 — D28 Bottom-finishing amount of boring D29 Chip removal time D30 Number of incomplete threads in tapping cycle D31 Tapper elongation amount for tapping D32 Number of spindle revolutions until spindle CCW rotation begins in tapping cycle D33 Back-boring tool tip relief D34 — D35 Prehole-drilling diameter setting element for reamer (dril
Return to Library PARAMETER Address (bit) 2 Outline D52 Reduction ratio for the G00-based relief rate during a very-deep-hole drilling cycle D53 Number of times of pecking up to the return of the tool to a position near the starting point of the very-deephole drilling cycle of a drilling or turning-drilling unit D54 Deceleration rate at cutting start for very-deep-hole drilling cycle/decremental very-deep-hole machining cycle D55 Drilling return distance for very-deep-hole drilling cycle/decreme
Return to Library 2 PARAMETER Address (bit) Outline 6 During planetary tapping, chips are ejected/not ejected automatically prior to the threading process. 7 — D93 Unidirectional positioning for point-machining D94 Unidirectional positioning for point-machining D95 Auto-setting method for tapping D96 - D144 — 2.
Return to Library PARAMETER Address (bit) 2 Outline E20 Axial cutting feed override during Z-axial cutting in the pecking mode of face machining E21 Wall-cutting overlap in closed figure E22 Override value of automatic corner over-riding E23 Effective removal allowance (upper limit) of automatic corner overriding E24 Effective removal allowance (lower limit) of automatic corner overriding E25 Effective angle (upper limit) of automatic corner overriding E26 Calculation coefficient for the f
Return to Library 2 PARAMETER Address (bit) Outline E62 3-D, Search length for right-angle cutting E63 3-D, Pattern display division segment (FL direction) E64 3-D, Pattern display division segment (GL direction) E65 3-D, Radial cutting allowance for area check E66 3-D, Axial cutting allowance for area check E67 - E75 3-D, Processing error tolerance E76 3-D, Entire-width override E77 3-D, Radial cutting allowance for high-speed rough processing (workpiece size appointment) E78 3-D, Mul
Return to Library PARAMETER Address (bit) Outline E100 - E103 — E104 Tool path selection E105 - E144 — 3. EIA/ISO (F) Address (bit) Outline F1 G61.1 corner deceleration coefficient (%) F2 G61.
Return to Library 2 PARAMETER Address (bit) Outline F22 Deceleration area of automatic corner overriding (G62) F23 - F26 — F27 Handling of G92 (spindel speed clamp value) command at restart F28 Threading chamfering angle F29 Override value of automatic corner overriding (G62) F30 G-code type selection F31 - F39 — F40 Operating method selection in tape mode F41 Threading termination waiting time processing F42 Deceleration area r during Z-axis measurement F43 Measurement area d duri
Return to Library PARAMETER Address (bit) F79 F80 F82 F83 Outline 0 Holding of memory monitor address valid/invalid 1 Selection of menu display 2 Key history function valid/invalid 3 Tool search method 4 Selection of tap gear 5 Display of tools currently in use valid/invalid 6 Initial value of synchronous/asynchronous tapping during tapping tool registration 7 Display of a MAZATROL monitor window valid/invalid 0 MAZATROL function valid/invalid 1 Automatic display of the navigation
Return to Library 2 PARAMETER Address (bit) F84 F85 F86 Outline 2 — 3 — 4 Program conversion type selection 1 5 Program conversion type selection 2 6 CMT/DNC input conversion type selection (only for lathe) 7 — 0 Fixed value (1) 1 Fixed cycle (B → J) 2 Spare tool search for EIA 3 Timing to validate new workpiece offset data specified with a system variable 4 Machine coordinate system (G92) selection 5 Incremental/absolute data command in high-speed machining mode 6 Tape oper
Return to Library PARAMETER Address (bit) F87 Outline 5 Override scheme for G1 during tool tip point control 6 Selection of rotary axis reference position for tool tip point control 7 Display format of REMAIN on the POSITION display 0 Selection of whether or not the tool is to be offset by each change only in the deviation vector 1 Selection of whether or not the check for mismatch of the workpiece origin and table rotation center is to be conducted 2 Data alteration checking function valid/
Return to Library 2 PARAMETER Address (bit) F93 F94 F95 Outline 5 Tool-diameter compensation (G41 or G42) interference check 6 Fixed-cycle hole-drilling axis 7 Tool diameter compensation for an EIA/ISO program 0 — 1 Modal at power-on or at reset (G94/G95) 2 Modal at power-on or at reset (G91/G90) 3 Tool length of tool data for EIA/ISO program, valid/invalid 4 Feed rate during machine lock 5 Middle point during reference-point return 6 Single-block operation mode at user macro oper
Return to Library PARAMETER Address (bit) F96 Outline 0 Selection of variable number for tool offset amount 1 Fairing function valid/invalid 2 Processing for arc command blocks in high-speed machining mode, nonuniform feed/uniform feed 3 — 4 Selection of a corner judgment criterion in high-speed machining mode 5 Selection of a cutting feed clamping speed in high-speed machining mode 6 Rotational axis shape correction valid/invalid 7 — F97 Selection of G-code of the coordinates system to
Return to Library 2 PARAMETER Address (bit) 5 Tool correction amount selection for EIA/ISO programs 6 Execution mode selection for a fixed turning cycle 7 Form of single-block stop during a fixed turning cycle F112 F113 F114 Outline Selection of measurement data items to be printed out 0 Counting all types of use under the same tool number for the tool life management on the TOOL DATA display executed/not executed 1 Data handling on the milling tool of a group that has expired in tool life 2
Return to Library PARAMETER Address (bit) 2 Outline F122 Clamping speed for the threading cycle — Z-axis F123 — F124 Permissible data alteration amount 1 for input error prevention function F125 Permissible data alteration amount 2 for input error prevention function F126 - F132 — F133 Pitch of tapping tool for display in detail in solid mode F134 Thread depth of tapping tool for display in detail in solid mode F135 Tool-drawing accuracy in solid mode F136 Amount of offset for dummy wo
Return to Library 2 PARAMETER Address (bit) F163 1 Type of passage of tool tip point through singular point 2 Chamfer/corner R-command address selection 3 Fixed hole-machining cycle return selection 4 6 digits in T-command for turning 5 Use of the M Pro scheme as the method of selecting the Length correction axis bit 6 MAZATROL program check for missing Z-offset, valid/invalid 7 Encoder polarity selection 0 Bar feeder scheduling function, valid/invalid 1 Incorporation of wear offset da
Return to Library PARAMETER Address (bit) Outline 5 — 6 — 7 — F167 — F168 — 4.
Return to Library 2 PARAMETER Address (bit) I14 0 Mirror image with respect to the machine zero point, valid/invalid 1 — 2 User software limits (I2, I3) valid/invalid 3 Tool-tip relief after spindle orientation during execution of G75, G76, G86 or point-machining (boring or backboring), valid/invalid 4 Direction of tool-tip relief after spindle orientation during execution of G75, G76, G86 or point-machining (boring or back-boring) 5 — 6 — 7 — I15 - I24 5.
Return to Library PARAMETER Address (bit) 2 Outline SU16 Movement to C-axis index swivel position when Z-offset scheme is used SU17 - SU48 — SU49 Delay timer for the parts catcher SU50 Tool turning clearance (radial value) in X-axis SU51 Tool turning clearance in Z-axis SU52 Lower-turret retraction function - Tool number of the retraction tool 1 SU53 Lower-turret retraction function - Tool number of the retraction tool 2 SU54 - SU96 — SU97 SU100 Lower-turret retraction function - Fixed
Return to Library 2 PARAMETER 6.
Return to Library PARAMETER Address (bit) 2 Outline TC27 Recessing width for #1 to #3 TC28 Recessing depth #1 to #3 TC29 Recessing width for #4 TC30 Recessing depth for #4 TC31 Recessing width for #5 TC32 Recessing depth for #5 TC33 Recessing width for #6 TC34 Recessing depth for #6 TC35 — TC36 — TC37 Safety contour clearance — Outside diameter clearance (radial value) TC38 Safety contour clearance — Inside diameter clearance (radial value) TC39 Safety contour clearance — Front
Return to Library 2 PARAMETER Address (bit) Outline TC54 Cut depth per cycle for machining inside diameter in bar machining unit TC55 Reverse feed tolerance for contour machining TC56 Overtravelling in X-axis direction in edge machining unit TC57 Workpiece pressing speed in workpiece transfer unit TC58 Spindle speed (min–1) of two spindles in workpiece transfer while the spindles are rotating in workpiece transfer unit TC59 Workpiece pressing distance in workpiece transfer unit TC60 — TC6
Return to Library PARAMETER Address (bit) 2 Outline TC81 Final finishing repeat times in the composite-type fixed cycle (G276) TC82 Chamfering data calculation coefficient in thread cutting unit and thread cutting cycle (G276/G292) TC83 Number of cutting operations to be performed on finishing allowance corresponding to standard pattern (#0) of threading unit TC84 Feed rate to be auto-set for finishing TC85 - TC94 Specification of the pocket for the long boring bar TC95 Fixed value TC96 Fi
Return to Library 2 PARAMETER Address (bit) TC142 5 Selecting an angle margin for nose shape compensation 6 CHUCK JAW DATA display name/code selection 7 Whether to make the partition plate and the workpiece barrier valid 0 Fixed value (0) 1 Selecting an inter-unit relief path when a succession of I.D.
Return to Library PARAMETER 7.
Return to Library 2 PARAMETER 2-2-2 Machine parameter 1. CALL MACRO (J) Address (bit) Outline J1 - J40 G-code macroprogram call J41 - J80 M-code macroprogram call J81 - J90 — J91 - J107 Parameter for system internal setting J108 - J144 — 2.
Return to Library PARAMETER Address (bit) Outline K21 Coefficient to determine rotation angle when retrying measurement C reference face K22 Measurement retry frequency when retrying reference face C measurement K23 Retry frequency for workpiece measurement K24 - K28 Predetermined value K29 Simultaneous control: Delay counter for automatic correction of synchronizing errors K30 Approach speed for laser tool length measurement K31 Approach speed for laser tool diameter measurement K32 Pre-
Return to Library 2 PARAMETER Address (bit) Outline K53 Vocal output language selection K54 Vocal output sound level K55 Vocal output warning reference value K56 Name of second auxiliary function K57 Type of S-code macroprogram ap-pointment call K58 Type of T-code macroprogram ap-pointement call K59 Type of second auxiliary function macroprogram appointment call K60 Fixed value (4) K61 Fixed value (1) K62 Fixed value (1) K63 Fixed value (1) K64 Fixed value (2) K65 Fixed value (
Return to Library PARAMETER Address (bit) Outline K85 Special linear acceleration/deceleration time constant for threading K86 - K89 — K90 Return override during synchronous tapping K91 Alternative M-code for M96 K92 Alternative M-code for M97 K93 Fixed value (2) K94 — K95 K96 0 — 1 Fixed value (0) 2 Tool position compensation during T-command execution, performed/not performed 3 Coordinate system update during handle pulse interrupt, performed/not performed 4 Fixed value (0) 5
Return to Library 2 PARAMETER Address (bit) K101 K102 K103 K104 K105 Outline Dynamic offset, name of orthogonal axis 0 — 1 — 2 Length of linear acceleration/deceleration filter II 3 Length of linear acceleration/deceleration filter II 4 Length of linear acceleration/deceleration filter II 5 Length of linear acceleration/deceleration filter II 6 Handling of the acceleration/deceleration filters for shape correction 7 Fixed value (0) 0 — 1 Synchronous control error auto-correction v
Return to Library PARAMETER Address (bit) K106 K107 Outline 3 T-code macro call invalid/valid 4 Second auxiliary function macro call invalid/valid 5 Fixed value (0) 6 Fixed value (0) 7 Input in millimeter/inch 0 Execution conditions for user macroprogram interrupt 1 Start timing for user macroprogram interrupt 2 Fixed value (0) 3 Pitch error setting 4 Fixed value (0) 5 Fixed value (0) 6 Fixed value (0) 7 Fixed value (0) 0 Fixed value (0) 1 — 2 — 3 — 4 — 5 — 6 Dec
Return to Library 2 PARAMETER Address (bit) Outline K114 Axis number of the horizontal axis in the rectangular coordinate system K115 Axis number of the vertical axis in the rectangular coordinate system K116 Axis number of the height axis in the rectangular coordinate system K117 Rotational direction of the rotary axis K118 - K120 — K121 Axis number of the first rotary axis K122 Horizontal axis rotational center offset of the first rotary axis K123 Vertical axis rotational center offset
Return to Library PARAMETER Address (bit) Outline L12 Tolerance for manual measurement L13 Allowable angle for parallelism and right angle in manual measurement L14 Escapement for straightness measurement L15 Macro program number for straightness measurement L16 Parameter for system internal setting L17 — L18 Presence/absence of tailstock L19 — L20 — L21 Output type of index (rotary) table L22 Data of the tool nose measurement sensor, Sensor width along the X-axis L23 Data of the
Return to Library 2 PARAMETER Address (bit) Outline L44 Selection of automatic setting on/off for nose position correction of a drilling tool L45 Index table angle command L46 Maximum number of pallets in pallet changing unit L47 To prepare or not to prepare next pallet change L48 Number of long boring bars L49 Simultaneous operation of pallet change with ATC L50 Rewriting of head number L51 Tool command system in MDI operation L52 Writing of machining management data with macro variab
Return to Library PARAMETER Address (bit) Outline L71 Shift of basic coordinate for oblique face machining L72 — L73 Time constant for shape coorection acceleration/deceleration filter 2 L74 Cutting feed rate for pre-interpolational acceleration/deceleration control L75 Time constant for pre-interpolational linear control during cutting feed rate acceleration/deceleration L76 Acceleration rate for high-speed cutting L77 Angle for deceleration at corner before interpolation L78 — L79 In-
Return to Library 2 PARAMETER Address (bit) L106 L107 0 Measuring equipment selection 1 Selection of a rotational reference coordinate system for WPC-th 2 Selection of measuring equipment 3 Selection of whether workpiece measurement results and tool measurement results are to be stored into tool data of the lower turret 4 Selection of whether to enable or disable the fixed amount compensation function 5 Selection of measurement execution timing 6 Selection of tool measurement operation 7
Return to Library PARAMETER Address (bit) Outline 2 Axis name of the secondary spindle 3 Whether to disable or enable the display of “section to be machined” in the milling tool sequence 4 Display of the BUFFER, REMAIN and POSITION information during coordinate conversion 5 — 6 — 7 Z-axis direction L111 — L112 — L113 Interference check reference axis (1st set of axes) L114 Interference check reference axis (2nd set of axes) L115 Interference check reference axis (3rd set of axes) L
Return to Library 2 PARAMETER Address (bit) Outline L132 Acceleration/deceleration filter (2nd stage), G0 time constant L133 - L138 — L139 Minimum usable tool diameter of the measurable chamfering tool L140 - L144 — 4. FEED VEL.
Return to Library PARAMETER Address (bit) M18 M19 M20 Outline 5 Rotational direction of servo motor (for movement in (+) direction) 6 — 7 Alarm/No alarm with axis removed 0 Type of C-axis 1 — 2 Machine zero-point position 3 — 4 Watchdog-less axis 5 X-axis current position display in radius/diameter 6 Automatic/manual simultaneous absolute-value updating 7 Absolute-value detection 0 — 1 — 2 — 3 In-position checking method 4 — 5 Homing operation starting position check
Return to Library 2 PARAMETER Address (bit) M21 M22 Outline 0 Rapid-feed acceleration/deceleration type, Linear acceleration/deceleration 1 Rapid-feed acceleration/deceleration type, First-order lag 2 Rapid-feed acceleration/deceleration type, Second-order lag 3 Rapid-feed acceleration/deceleration type, Exponential acceleration/linear deceleration 4 Cutting-feed acceleration/deceleration type, Linear acceleration/deceleration 5 Cutting-feed acceleration/deceleration type.
Return to Library PARAMETER Address (bit) Outline M34 Safety clamping speed for Safety supervisory mode 2 M35 Safety clamping speed for Safety supervisory mode 3 M36 Speed supervisory door selection M37 Safety clamping speed reduction judgment coefficient M38 Interference check distances for Intelligent Safety Shield, primary check distance M39 Interference check distances for Intelligent Safety Shield, secondary check distance M40 - M48 — 5. TIME CONST.
Return to Library 2 PARAMETER Address (bit) Outline N19 Axis system number N20 — N21 0 Linear-type rotational axis 1 Rotational axis shortcut 2 Fixed value (0) 3 Bi-directional pitch error correction 4 Reference axis for superposition control 5 Superposition axis for superposition control 6 Relative polarity of control axis 7 — N22 - N24 — N25 Time constant for deceleration rate calculation N26 Accuracy coefficient for deceleration rate calculation N27 Rapid feed time consta
Return to Library PARAMETER Address (bit) Outline S3 Feed forward gain for the MAZAK Precision Rapid Boring Tornado Option S4 Feed forward gain S5 Rotational center of the table S6 Absolute position detection parameter S7 Upper limit (on Z-axis) of machining range for table rotating machining Ι S8 Feed-forward gain G00 S9 — S10 Axis of rotation of the tilting table S11 Corner position of the tilting table S12 Axis of rotation of the tilting table (Used for the automatic program origin
Return to Library 2 PARAMETER 7.
Return to Library PARAMETER Address (bit) 1 2 3 4 5 2 Outline — — — — — 6 — 7 Considering/Ignoring the spindle/motor gear ratio SA48 Encoder signal input destination SA49 Speed attainment detection width SA50 Spindle type SA51 Number of gears on spindle SA52 Turning spindle type SA53 Spindle 1/4h (1/2h) rated torque for auto-pecking of the cutting load detection type — L coils SA54 Spindle 1/4h (1/2h) rated torque for auto-pecking of the cutting load detection type — H coils SA55 Spi
Return to Library 2 PARAMETER Address (bit) Outline SA74 - SA80 Output in the following spindle output diagrams: MACHINING NAVIGATION-RESULT/MACHINING NAVIGATION-PPEDICTION/Monitoring Functions SA81 Spindle limit speed selection for spindle position control time constants — Limit speed 1 SA82 Spindle limit speed selection for spindle position control time constants — Limit speed 2 SA83 Spindle limit speed selection for spindle position control time constants — Limit speed 3 SA84 Spindle positi
Return to Library PARAMETER Address (bit) Outline SA120 PLG pulse rate for spindle index gear tooth correction SA121 Amount of branching [1] point correction for spindle index gear tooth SA122 Amount of branching [2] point correction for spindle index gear tooth SA123 Amount of branching [3] point correction for spindle index gear tooth SA124 Amount of branching [4] point correction for spindle index gear tooth SA125 Amount of branching [5] point correction for spindle index gear tooth SA126
Return to Library 2 PARAMETER 8. BARRIER (BA) Address (bit) Outline BA1 Chuck outside diameter (for chuck barrier) — No. 1 turning spindle BA2 Chuck width (for chuck barrier) — No. 1 turning spindle BA3 Chuck inside diameter (for chuck barrier) — No. 1 turning spindle BA4 EIA program workpiece outside diameter BA5 Chuck outside diameter (for chuck barrier) — No. 2 turning spindle BA6 Chuck width (for chuck barrier) — No.
Return to Library PARAMETER Address (bit) Outline BA27 Tool holder mounting position — Type 1 BA28 Tool holder width in X-axis direction — Type 1 BA29 Tool holder width in Z-axis direction — Type 1 BA30 Tool holder mounting position — Type 2 BA31 Tool holder width in X-axis direction — Type 2 BA32 Tool holder width in Z-axis direction — Type 2 BA33 Tool holder mounting position — Type 3 BA34 Tool holder width in X-axis direction — Type 3 BA35 Tool holder width in Z-axis direction — Type
Return to Library 2 PARAMETER Address (bit) Outline BA54 Selection of work spindle for hobbing BA55 Turning spindle number for polygonal machining (D1) BA56 Turning spindle number for polygonal machining (D2) BA57 Turning spindle number for polygonal machining (D3) BA58 Turning spindle number for polygonal machining (D4) BA59 Spindle forward rotation M-code for tapping cycle BA60 Spindle reverse rotation M-code for tapping cycle BA61 Amount of runout of the B-axis center BA62 Amount of
Return to Library PARAMETER Address (bit) Outline BA93 Upper/lower turret tool angle difference (HD1) BA94 Upper/lower turret tool angle difference (HD2) BA95 Tool nose measurement, sensor width along the X-axis BA96 Tool nose measurement, sensor width along the Z-axis BA97 Tool nose measurement, X-coordinate of the sensor’s reference point BA98 Tool nose measurement, Y-coordinate of the sensor’s reference point BA99 Tool nose measurement, Z-coordinate of the sensor’s reference point BA100
Return to Library 2 PARAMETER Address (bit) Outline 2 EIA tool barrier, tool holder present/absent 3 Barrier tool nose position (EIA, automatic) 4 Setting of BA11 is handled as tailstock extruding length, valid/invalid 5 Output of spindle revolution M-code specified in same block as synchronous tapping, valid/invalid 6 — 7 — 0 System to be made valid without system selection for queuing 1 Y-axis interference type 2 Y-axis moving range display 3 Tool command scheme 4 FLASH tool vali
Return to Library PARAMETER 2-2-3 2 Data I/O parameter 1. CMT parameter (CMT) Address (bit) Outline CMT1 CMT24 — CMT25 Type of processing to be executed if the tool quantity data within the NC memory mismatches that of the CMT CMT26 CMT32 — 2.
Return to Library 2 PARAMETER Address (bit) Outline TAP27 Bit parameter related to program end code (M) for paper tape reader TAP28 — TAP29 Number of characters in feed section for paper tape puncher TAP30 Number of characters in the space between O-number and program for paper tape puncher TAP31 Number of characters in the space between programs for paper tape puncher TAP32 — 3.
Return to Library PARAMETER Address (bit) 2 Outline DNC22 DNC24 — DNC25 0 Type of processing to be executed if the tool quantity data within the NC memory mismatches that which has been transferred from the DNC memory 1 — 2 Handling of tool data and tool files in the M PLUS format, valid/invalid 3 — 4 — 5 — 6 — 7 — DNC26 0 After program reception, a search is made/not made for the work number of that program. 1 Details of an alarm occurring in DNC are displayed or not.
Return to Library 2 PARAMETER 4.
Return to Library PARAMETER 2-3 Detailed Description 2-3-1 Structure of the parameter list Each parameter list is written in the following format: [1] Classification Address [2] Display title Meaning Description [4] [9] [3] Program type Conditions Unit Setting range [5] [6] [7] [8] [1] Classification of parameters (USER, MACHINE or DATA I/O) [2] Characters displayed at the upper part of the screen [3] Parameter address displayed on the screen - Bit input type parameters have the bit No.
Return to Library 2 PARAMETER [6] Conditions under which a changed parameter becomes valid Example 1: “Immediate” designates that new parameter value becomes effective upon parameter change. Example 2: “At power on” designates that new parameter value will become effective after procedure below. 1. Change parameter setting value. (By procedure similar to changing of ordinary data) ! 2. Press power off button on the operation panel. ! 3. Press power on button on the operation panel.
Return to Library PARAMETER 2-3-2 User parameter POINT (D) USER Classification Address 2 POINT Display title Meaning Description Height of the second R-point Initial point D1 Second R-point MPL001 Height of the second R-point during point machining D1 The height of the R-point during point machining is basically D41, however, it is changed to D1 under the following conditions. Tool sequence Program type M Conditions Immediate Unit 0.1 mm/0.
Return to Library 2 PARAMETER USER Classification Address POINT Display title Meaning Description Element used to set the maximum spot-chamfering hole diameter (d) during automatic tool development Spot-chamfering occurs if d ≤ D2 – D4. If d > D2 – D4, the chamfering cutter is developed automatically. D2 Maximum allowable spot-chamfering hole diameter element d D4 Program type M Conditions Immediate Unit 0.1 mm/0.
Return to Library PARAMETER USER Classification Address 2 POINT Display title Meaning Description Element used to automatically set the number of drills which are automatically developed according to the hole diameter of the drill unit Number of drills developed Maximum diameter of holes machinable on one drill Conditions DIA ≤ D8 1 D8 Program type M Conditions Immediate Unit 1 mm/0.
Return to Library 2 PARAMETER USER Classification Address POINT Display title Meaning Description Element used to automatically set the hole-drilling depth during automatic tool development of stop-hole counter-boring and stop-hole boring units DEPTH Stop-hole machining hole-bottom clearance D12 MPL006 D12 Example: SNo. Program type M Conditions Immediate Unit 0.1 mm/0.01 inch Setting range 0 to 99 1 TOOL NOM-φ DRILL 10. No. HOLE-φ HOLE-DEP 19.
Return to Library PARAMETER USER Classification Address 2 POINT Display title Meaning Description Z-axis feed dwell time at the hole bottom in the chamfering cycle of chamfering cutter or spot-machining tool. Set this time in spindle revolutions.
Return to Library 2 PARAMETER USER Classification Address POINT Display title Meaning Description Element used to automatically set the radial depth-of-cut per end milling operation Depth-of-cut = nominal diameter × D20 Radial depth-of-cut setting element for end milling Depth-of-cut is automatically set according to the value of this parameter when nominal diameter of the end mill is input. Example: D20 SNo. TOOL NOM-φ No. HOLE-φ HOLE-DEP PRE-DIA PRE-DEP RGH DEPTH 1 END MILL 20. 40. 10. 30. 0.
Return to Library PARAMETER USER Classification Address 2 POINT Display title Meaning Description Z-axis feed dwell time at the hole bottom in a boring cycle. Set this time in spindle revolutions. When the boring bar reaches the hole bottom, the Z-axis will firstly stop moving until the spindle makes D24 revolutions, and then the spindle orientation will be performed.
Return to Library 2 PARAMETER USER Classification Address POINT Display title Meaning Description The distance which the boring bar is fed in at 70% of the original feed rate to finish the hole bottom Bottom-finishing amount of boring D28 D28 Program type M Conditions Immediate Unit 0.1 mm/0.01 inch Setting range 0 to 99 MPL016 The feed rate is reduced to 70% of the original value before the hole bottom is reached.
Return to Library PARAMETER USER Classification Address 2 POINT Display title Meaning Description Excess amount of tool return due to elongation of the tapper during tapping cycle Set this value in spindle revolutions.
Return to Library 2 PARAMETER USER Classification Address POINT Display title Meaning Description Prehole-drilling diameter setting element for reamer (drilling) Element used to automatically set the prehole-drilling diameter during automatic tool development of the reamer unit (When the pre-machining process is drilling.) DIA D35 DIA – D35 Program type M Conditions Immediate Unit 0.01 mm/0.
Return to Library PARAMETER USER Classification Address 2 POINT Display title Meaning Description 1) In automatic tool development of the reamer unit, if the pre-machining process is boring: DIA Reamer-prehole diameter setting element for boring or end milling Boring-hole diameter = DIA – D38 D38 MPL021 Program type M Conditions Immediate Unit 0.01 mm/0.001 inch Setting range 0 to 999 Example: SNo. TOOL 1 BOR BAR 2) NOM-φ No. 10. HOLE-φ 10.
Return to Library 2 PARAMETER USER Classification Address POINT Display title Meaning Description Height of the third R-point Initial point D42 Third R-point MPL001 Height of the third R-point during point machining The height of the R-point during point machining is basically D41, however it is changed to D42 under the following conditions. D42 Tool sequence Conditions - Bit 6 of parameter D91 is set to 1 (D42 valid).
Return to Library PARAMETER USER Classification Address POINT Display title Meaning Description Invalid — D44 Program type — Conditions — Unit — Setting range — q1 1st time i-th time Drilling depth q1 qi q2 Gradual decrements in drilling depth D45 qn qi b qn 1 Program type Immediate Unit 0.01 mm/0.
Return to Library 2 PARAMETER USER Classification Address POINT Display title Meaning Description Element used to automatically set the hole depth (HOLE-DEP) of drilling, end milling and boring during automatic tool development of the reamer unit Reamer-prehole machining overshoot DEPTH DEPTH D47 D47 D47 Program type M Conditions Immediate Unit 0.01 mm/0.
Return to Library PARAMETER USER Classification Address 2 POINT Display title Meaning Description The feed rate will be auto-set to D51 when the planetary tapping cycle is selected. SNo. TOOL NOM-φ No.HOLE-φ HOLE-DEP PRE-DIA PRE-DEP RGH DEPTH C-SP FR M M Auto-set feed rate for planetary tapping cycle 1 TAP M10. 10. 23.7 PLANET 0.15 FIX P1.5 50 0.04 ↑ D51 D51 Program type M Conditions Immediate Unit 0.01 mm/rev 0.
Return to Library 2 PARAMETER USER Classification Address POINT Display title Meaning Description D54 F’= F × 100 F : Specified feed rate F' : Feed rate at cutting start Programmed start point End point θ Drill D Deceleration rate at cutting start for verydeep-hole drilling cycle/decremental verydeep-hole machining cycle D54 l Feed rate at F' over distance l from the programmed start point D 2 × tanθ/2 l= (0° < θ < 180°) l=0 Program type M Conditions Immediate Unit % Setting rang
Return to Library PARAMETER USER Classification Address Display title Meaning 2 POINT Description Set the return speed for the very-deep-hole drilling cycle or the decremental very-deep-hole machining cycle. Return speed for very-deep-hole drilling cycle/decremental very-deep-hole machining cycle D57 Program type M Conditions Immediate Unit 0.001 mm/rev 0.
Return to Library 2 PARAMETER USER Classification Address Display title Meaning POINT Description Set the circumferential speed reduction ratio at cutting end of a verydeep-hole drilling cycle (through hole) during the point machining.
Return to Library PARAMETER USER Classification Address Display title Meaning 2 POINT Description Specify DEP-Z range for the end mill and the face mill from the learning data of cutting conditions. D73 to D77 Learning of cutting conditions (DEP-Z range) Program type M Conditions Immediate Unit 0.1% (0.1 mm/0.01 inch) Setting range 0 to 1000 When learning data on the condition that DEP-Z is in the following range has been stored in the memory, learning is not effectuated again.
Return to Library 2 PARAMETER USER Classification Address POINT Display title Meaning Description 76543210 (1: Execution, 0: No execution) M04 is output after the tool has dwelled at the hole bottom during a tapping cycle. The tool dwells after M04 has been output at the hole bottom during a tapping cycle. The tool dwells after it has been returned to the R-point during a tapping cycle. If a drill is used in the pre-machining of the centering drill cycle, the R-point height is set to D1.
Return to Library PARAMETER USER Classification Address Display title Meaning 2 POINT Description Unidirectional positioning for point-machining 76543210 (1: Execution, 0: No execution) END MILL (End mill) — Planetary tapping Tornado cycle D94 Program type M Conditions Immediate Unit Bit Setting range Binary, eight digits Selection of the auto-setting method to be used for the MAZATROL program data items of the tapping unit (TAPPING and CBOR-TAP) and the diameter item of pipe taps on t
Return to Library 2 PARAMETER 2-3-3 User parameter LINE/FACE/3D (E) USER Classification Address LINE/FACE/3D Display title Meaning Description Element used to set cutting start point and escape point for closed-pattern line- or face-machining Example: Defined closed pattern Defined closed pattern SRV-R E2 Closed-pattern cutting start point and escape point setting element E1 Cutting start point E2 E1 Escape point MPL026 E1 [Applicable units] - LINE OUT, LINE IN, CHMF OUT and CHMF IN - Wa
Return to Library PARAMETER USER Classification Address 2 LINE/FACE/3D Display title Meaning Description Invalid — E3 Program type — Conditions — Unit — Setting range — Reference allowance of finishing in radial direction The reference value of each finishing allowance R (FIN-R) which is automatically set when the roughness levels of the line- or face-machining units have been set The finishing allowance R in the case of roughness level 4 becomes the value of this parameter, and the val
Return to Library 2 PARAMETER USER Classification Address LINE/FACE/3D Display title Meaning Description Allowance of cutting start point in axial direction (the second clearance) E7 Allowance of cutting start point in axial direction For the line- or face-machining, E9 is used as an axial clearance for rapid access to the machining point from the initial point, however, E7 is used when the condition meets both of 1) and 2) mentioned below. 1) 2) There is pre-machining in the same unit.
Return to Library PARAMETER USER Classification Address 2 LINE/FACE/3D Display title Meaning Description The amount of clearance that prevents interference of the chamfering cutter with the bottom during chamfering Axial interference clearance of chamfering cutter E11 E11 Program type M Conditions Immediate Unit 0.1 mm/0.01 inch Setting range 5 to 40 Interference depth Interferes.
Return to Library 2 PARAMETER USER Classification Address LINE/FACE/3D Display title Meaning Description Element used to set the tool path external to the defined figure for reciprocating-short machining with face milling unit Example: Tool path setting element for face millingtop unit E15 (reciprocating short) Program type M Conditions Immediate Unit 10% Setting range 1 to 9 Tool diameter × E15 10 Tool diameter × E15 10 Defined figure MPL033 Override value of the idle-cutting feed ra
Return to Library PARAMETER USER Classification Address 2 LINE/FACE/3D Display title Meaning Description Override value of tool returning feed rate in the rough-machining process of the end milling-slot unit, when the bidirectional cutting is executed. Returning feed rate override in case of bidirectional cutting for rough-machining of the end milling-slot unit.
Return to Library 2 PARAMETER USER Classification Address LINE/FACE/3D Display title Meaning Description The range of removal allowances (upper and lower limits) The automatic corner overriding becomes valid when the following line- or face-machining conditions are met: Effective removal allowance (upper limit) of automatic corner overriding Tool Removal Tool E24 E23 diameter × 100 ≤ allowance ≤ diameter × 100 E23 Removal allowance Program type M Conditions Immediate Unit 1% Setting range
Return to Library PARAMETER USER Classification Address 2 LINE/FACE/3D Display title Meaning Description These parameters, the roughness code, etc. determine the finishing feed rate. Radial direction feed rate calculation reference diameter for finish cutting in line machining unit - If the radial-finishing feed rate is taken as F1, then: E28 × F1 = D E27 × α E28 × Kf × Z E27 × Kf × Z （D < E27 × α） （D ≥ E27 × α） D α Program type : Tool diameter : 0.1 (for metric specs.) or 0.
Return to Library 2 PARAMETER USER Classification Address LINE/FACE/3D Display title Meaning Description An element that determines the starting point and escape point of radial cutting when CLOSED is specified for the wall attributes at the starting point and ending point of open-pattern line machining. When OPEN is specified, E2 is used.
Return to Library PARAMETER USER Classification Address 2 LINE/FACE/3D Display title Meaning Description Element that automatically determines an approaching radius in a Zdirection helical approach scheme. The approaching radius value to be used in the Z-direction helical approach scheme for helical machining is automatically determined by the parameter as follows: Approaching radius = Element that automatically determines an approaching radius in a Z-direction helical approach scheme Tool dia.
Return to Library 2 PARAMETER USER Classification Address LINE/FACE/3D Display title Meaning Description The approaching distance value to be used in the Z-direction tapered approach scheme for tapered machining is automatically determined by the parameter as follows: Approaching distance = Tool dia.
Return to Library PARAMETER USER Classification Address 2 LINE/FACE/3D Display title Meaning Description The escape distance value to be used in the Z-direction tapered escape scheme after tapered machining is automatically determined by the parameter as follows: Element that automatically determines an escape distance in the Z-direction tapered escape scheme Escape distance = Tool dia.
Return to Library 2 PARAMETER USER Classification Address LINE/FACE/3D Display title Meaning Description Feed overriding for cutting a workpiece in an axial direction using a 3-D unit Example: 3-D Axial cutting-feed overriding FR × E55 10 FR × E55 10 E55 E59 Depth of cut Program type M Conditions Immediate Unit 10% Setting range 0 to 9 High-speed rough processing Finish processing MPL041 Note: Feed overriding is invalid when this parameter is 0.
Return to Library PARAMETER USER Classification Address 2 LINE/FACE/3D Display title Meaning Description Element used to set the position in which the cutting feed in axial direction is to be started after the tool has been moved from the initial point toward the workpiece at a rapid feed rate 3-D Allowance of axial-cutting start position Example: E59 E59 Material height Program type M Conditions Immediate Unit 0.1 mm/0.
Return to Library 2 PARAMETER USER Classification Address LINE/FACE/3D Display title Meaning Description The number of segments into which the defined pattern of a curved surface is to be divided for display of the curved-surface pattern on the TOOL PATH CHECK display 3-D Pattern display division segment (FL direction) Example: E64 E63 E63 Program type M Conditions Immediate Unit — Setting range 0 to 999 3-D Pattern display division segment (GL direction) GL or normal to FL FL MPL04
Return to Library PARAMETER USER Classification Address 2 LINE/FACE/3D Display title Meaning Description The processing error tolerance with respect to a curved-surface pattern which corresponds to a #T setting (1 through 9) of the tool sequence E67 to E75 3-D Processing error tolerance #T 1 2 3 4 5 6 7 8 9 Address E67 E68 E69 E70 E71 E72 E73 E74 E75 Example: Program type M Conditions Immediate Unit 0.01 mm/0.
Return to Library 2 PARAMETER USER Classification Address LINE/FACE/3D Display title Meaning Description Invalid — E79 to E82 E83 E84 Program type — Conditions — Unit — Setting range — 3-D Region of radial machining during highspeed rough processing (offset appointment) That amount of offset from a curved-surface pattern which determines the region of high-speed rough processing (offset appointment) in a radial direction Region to be machined Material height Program type M Conditi
Return to Library PARAMETER USER Classification Address 2 LINE/FACE/3D Display title Meaning Description The factor that determines the region of high-speed rough processing (workpiece size appointment) in a radial direction 3-D Region of radial machining during highspeed rough processing: –X E85 E88 (workpiece size appointment) E86 E85 Program type Curved-surface pattern M Conditions Immediate Unit 0.1 mm/0.
Return to Library 2 PARAMETER USER Classification Address LINE/FACE/3D Display title Meaning Description That distance from the bottom of a curved-surface pattern which determines the region of high-speed rough processing (workpiece size appointment) in an axial direction Example: Region to be machined Curved-surface pattern Material height +Z 3-D Region of axial machining during highspeed rough processing E89 E89 +X (workpiece size appointment) E85 E86 MPL054 Program type M Conditions
Return to Library PARAMETER USER Classification Address 2 LINE/FACE/3D Display title Meaning Description 76543240 0: Machining from inside to outside 1: Machining from outside to inside 0: Cutting direction inversed 1: Cutting direction fixed 0: The R-point height is set always to E9. 1: The R-point height is set to E7 or E9 when there is or isn’t pre-machining in the same unit, respectively. 0: The clearance on X-Y plane is set always to E2.
Return to Library 2 PARAMETER USER Classification Address Display title Meaning LINE/FACE/3D Description 76543210 0: Machining from inside to outside 1: Machining from outside to inside 0: Cutting direction inversed 1: Cutting direction fixed 0: The R-point height is set always to E9. 1: The R-point height is set to E7 or E9 when there is or isn’t pre-machining in the same unit, respectively. 0: The clearance on X-Y plane is set always to E2.
Return to Library PARAMETER USER Classification Address 2 LINE/FACE/3D Display title Meaning Description 76543210 For the 2nd and subsequent rounds of cutting: 0: Not via the approach point 1: Via the approach point For the 2nd and subsequent rounds of cutting: 0: Escape to the Z-axis initial point 1: No escape on the Z-axis 1: Rapid feed up to the intended surface + E9 1: Escape is set to a point where the tool comes out of the removal allowance.
Return to Library 2 PARAMETER USER Classification Address Display title Meaning LINE/FACE/3D Description 76543210 0: The R-point height is set always to E9. 1: The R-point height is set to E7 or E9 when there is or isn’t pre-machining in the same unit, respectively.
Return to Library PARAMETER USER Classification Address Display title Meaning 2 LINE/FACE/3D Description Invalid — E100 to E103 Program type — Conditions — Unit — Setting range — 76543210 Cutting method after line machining approach point auto-setting 0: Same operation as before auto-setting 1: Operation with manually entered data Tool path selection E104 Program type M Conditions Immediate Unit Bit Setting range Binary, eight digits This bit specifies the returning position fo
Return to Library 2 PARAMETER 2-3-4 User parameter EIA/ISO (F) USER Classification Address EIA/ISO Display title Meaning Description When (L74/L75) × (F1/100) is assigned as the allowable acceleration attained before corner deceleration is started, the theoretical value Vo of the corner deceleration in G61.
Return to Library PARAMETER USER Classification Address 2 EIA/ISO Display title Meaning Description Fixed value (0) F5 Program type — Conditions — Unit — Setting range — Specify the minimum height of stepped sections at which the axis feed is not to be decelerated in high-speed smoothing control mode. Minimum allowable height of stepped sections for deceleration in high-speed smoothing control mode F6 Program type E Conditions After stop of movement Unit 0.0001 mm/0.
Return to Library 2 PARAMETER USER Classification Address EIA/ISO Display title Meaning Description Circler cutting clamp speed Vc is adjusted using the value set in this parameter. Vc = Vc × Circler cutting clamp speed coefficient for high-speed smoothing control F9 100 The speed is not adjusted if 0 is set here. (Setting is handled as 100.) Setting more than 500 is disposed as 500. F9 Program type E Conditions Immediate Unit % Setting range 0 to 500 Not used.
Return to Library PARAMETER USER Classification Address 2 EIA/ISO Display title Meaning Description The allowance amount provided for the tool to stop moving at rapid-feed just in front of the preceding hole during a deep-hole drilling cycle or during G83 tool path Allowance amount of rapid-feed stop in deep-hole drilling cycle or in G83 F13 F13 Program type M, E Conditions Next block Unit 0.001 mm/0.
Return to Library 2 PARAMETER USER Classification Address EIA/ISO Display title Meaning Description Vector of coordinate rotation (axis of ordinate) Vertical length of coordinate rotation F17 Program type — Conditions At power on Unit 0.001 mm/0.0001 inch Setting range 0 to ±99999999 Angle of coordinate rotation F18 Program type — Conditions At power on Unit 0.
Return to Library PARAMETER USER Classification Address EIA/ISO Display title Meaning 2 Description The automatic corner override using the G62 code becomes valid when the following condition of the shape angle is met: Shape angle ≤ F21 Maximum inside-corner angle available with automatic corner override (G62) Pattern angle F21 Program type E Conditions Next command Unit 1° Setting range 0 to 179 Overriding occurs here.
Return to Library 2 PARAMETER USER Classification Address EIA/ISO Display title Meaning Description Set chamfering angle at thread portion in thread cutting cycle. G76 and G92 are used for threading cutting cycle, if F30 is set to 0. G276 and G292 are used for threading cutting cycle, if F30 is set to 1. Threading chamfering angle F28 F28 Program type E Conditions Immediate Unit 1° Setting range 45, 60 Chamfering data NM211-00219 Note: Set 45 or 60.
Return to Library PARAMETER USER Classification Address Display title Meaning 2 EIA/ISO Description 0: 1: 2: 3: Tape operation Hard disc operation IC memory card operation Ethernet operation Operating method selection in tape mode F40 Program type E Conditions Immediate Unit — Setting range 0 to 3 Set a threading termination waiting time. F41 = 0, 1 or 128 to 255 No waiting time Threading termination waiting time processing F41 = 2 to 127 (Setting – 1) × 3.
Return to Library 2 PARAMETER USER Classification Address EIA/ISO Display title Meaning Description Measuring speed (f) This data is used when argument F is omitted in G37 command format.
Return to Library PARAMETER USER Classification Address 2 EIA/ISO Display title Meaning Description Invalid — F67 F68 Program type — Conditions — Unit — Setting range — This parameter is used to select the method of specifying the EIA/ISO program restarting position. Two methods are available: 0: The whole program, including the subprograms, is subjected to this processing.
Return to Library 2 PARAMETER USER Classification Address EIA/ISO Display title Meaning Description To select whether the shape correction function of the MAZATROL program is always effective or ineffective.
Return to Library PARAMETER USER Classification Address 2 EIA/ISO Display title Meaning Description The tool-path check time study time that is accumulated each time a Bcode is output. B-code execution time for time study F76 Program type M, E Conditions Immediate Unit 0.01 sec. Setting range 0 to 10000 The basis rate for the NC to judge whether the tool is to be displayed in reverse display mode on the TOOL DATA display to indicate that the life of that tool is approaching expiry.
Return to Library 2 PARAMETER USER Classification Address Display title Meaning EIA/ISO Description 76543210 Holding of memory monitor address 0: No 1: Yes Selection of menu display 0: Menu for machining centers 1: Menu for turning centers Key history function 0: Yes 1: No Tool search method 0: In order of TNo. 1: In order of TNo.
Return to Library PARAMETER USER Classification Address Display title Meaning 2 EIA/ISO Description 76543210 Program management function 0: Normal 1: Editing prohibited (in 9000’s) Program management function 0: Normal 1: Dieplaying prohibited (in 9000’s) Fixed value (0) Add-in MAZATROL 0: Invalid 1: Valid — Program management function 0: Normal 1: Editing prohibited (in 8000, 9000’s) F81 Program management function 0: Normal 1: Displaying prohibited (in 8000, 9000’s) Retaining the program tran
Return to Library 2 PARAMETER USER Classification Address Display title Meaning EIA/ISO Description 76543210 Output of the alarm history data as text data 0: Valid 1: Invalid Operation record function 0: Invalid 1: Valid Program conversion type selection 1 0: Based on program conversion type selection 2 1: Conversion of M640MT/M640MT Pro into a Z/C offset scheme or conversion of M640M Pro into a WPC scheme Program conversion type selection 2 0: Conversion into the WPC scheme 1: Conversion into the
Return to Library PARAMETER USER Classification Address Display title Meaning 2 EIA/ISO Description 76543210 Tool offset data is taken into account for the current-position counter during execution of EIA programs 0: No 1: Yes Fixed cycle (B → J) 0: B 1: J Spare tool search for EIA 0: Group number assignment 1: Tool number assignment Timing to validate new workpiece offset data specified with a system variable 0: Valid when the workpiece offset is specified after a system variable is entered.
Return to Library 2 PARAMETER USER Classification Address EIA/ISO Display title Meaning Description 76543210 Table rotational machining 0: Always valid 1: Outside the area only Ignorance of radial interference check Type of coordinate system for controlling the tool tip point 0: The table coordinate system that rotates according to the particular rotation of the C-axis is defined as the programming coordinate system. 1: The work coordinate system is defined as the programming coordinate system.
Return to Library PARAMETER USER Classification Address Display title Meaning 2 EIA/ISO Description 76543210 Output of M250 (Spindle Speed Confirmation) before a turning feed 0: Not to output 1: To output Milling-spindle start timing for a milling unit (with MILL&TURN. set under TYPE of UNo.
Return to Library 2 PARAMETER USER Classification Address Display title Meaning EIA/ISO Description 76543210 Gap offset type 0: Moves the machine. 1: Does not move the machine.
Return to Library PARAMETER USER Classification Address 2 EIA/ISO Display title Meaning Description Set this parameter to specify functions related to the conversion from MAZATROL program into an EIA program. 76543210 Conversion of a part of program into sub-program (See Note.) Output method of G-code for point machining 0: G-code of fixed cycle 1: G-code in 1 digit Output of G10 and G92.
Return to Library 2 PARAMETER USER Classification Address Display title Meaning EIA/ISO Description Set this parameter to specify functions related to the conversion from MAZATROL program into an EIA program. 76543210 Output of shape data 0: Not to output 1: To output Change over synchronous tapping G-code 0: To output G74/G84 1: To output G84.2/G84.
Return to Library PARAMETER USER Classification Address Display title Meaning 2 EIA/ISO Description 76543210 — F91 Program type M, E Conditions At power on Unit Bit Setting range Binary, eight digits In response to move command without decimal point: 0: Tool moves by 1/1. 1: Tool moves by 10/1.
Return to Library 2 PARAMETER USER Classification Address Display title Meaning EIA/ISO Description 76543210 Modal at power-on or at reset 0: G94 (Feed per minute) 1: G95 (Feed per revolution) Modal at power-on or at reset 0: G91 (Incremental-value command) 1: G90 (Absolute-value command) Tool length of tool data for EIA/ISO program 0: Invalid 1: Valid Feed rate during machine lock 0: Specified feed rate 1: Rapid feed rate Middle point during reference-point return 0: Return through middle point to
Return to Library PARAMETER USER Classification Address Display title Meaning 2 EIA/ISO Description 76543210 Interrupt function using user macro instruction 0: Invalid 1: Valid Handling of macroprogram interruption and call 0: Handled as interruption 1: Handled as subprogram call Automatic return position to restart the program (Fixed to 1) 0: Manual return 1: Automatic return G00 (positioning) command feed rate for dry run 0: Rapid feed rate 1: Feed rate for dry run Manual-pulse interrupt amount c
Return to Library 2 PARAMETER USER Classification Address EIA/ISO Display title Meaning Description To select G-code modal of the coordinates system to be used in the EIA conversion function.
Return to Library PARAMETER USER Classification Address 2 EIA/ISO Display title Meaning Description In case of output with subprogram in the EIA conversion function: F99 Offset amount for the subprogram WNo. to the main WNo. concerned in case of output with subprogram in the EIA conversion function Example: WNo. 10 When F99 is “20”. EIA conversion (The WNo. of the converted program is assumed to be 1000.) Main Sub WNo. 1000 WNo.
Return to Library 2 PARAMETER USER Classification Address EIA/ISO Display title Meaning Description Fine spline interpolation curve error During block checking in the fine spline interpolation mode, if the spline curve of a specific block is judged to include an inflection point and the maximum chord error between the spline curve and the block is larger than the value of F102, the shape of the curve will be modified to reduce the maximum chord error below the value of F102.
Return to Library PARAMETER USER Classification Address 2 EIA/ISO Display title Meaning Description Fine spline interpolation curve error During block checking in the fine spline interpolation mode, if the spline curve of a specific block is judged to include no inflection point and the maximum chord error between the spline curve and the block is larger than the value of F104, the shape of the curve will be modified to reduce the maximum chord error below the value of F104.
Return to Library 2 PARAMETER USER Classification Address EIA/ISO Display title Meaning Description Invalid — F109 F110 Program type — Conditions — Unit — Setting range — In the solid mode of the TOOL PATH CHECK display: F111 (bit 0) = 0: Simplified display of tapping tool Selection of display type of tapping tool in solid mode F111 F111 (bit 0) = 1: Detailed display of tapping tool (bit 0) Program type M Conditions Immediate Unit — Setting range 0, 1 F111 (bit 1) = 0: Disuse o
Return to Library PARAMETER USER Classification Address EIA/ISO Display title Meaning 2 Description Select the direction of rotation of the C-axis during C-axial threading based on G01.1. Direction of rotation of the C-axis during Caxial threading with G01.1 F111 F111 (bit 3) = 0: The C-axis rotates CW (forward). F111 (bit 3) = 1: The C-axis rotates CCW (backward).
Return to Library 2 PARAMETER USER Classification Address EIA/ISO Display title Meaning Description This parameter specifies whether single-block operation during a fixed turning cycle (G290, G292 or G294) is to be stopped after the entire cycle has been executed, or for each block.
Return to Library PARAMETER USER Classification Address Display title Meaning 2 EIA/ISO Description F113 (bit 2) = 0: Operation will be continued. Data handling on the turning tool of a group that has expired in tool life F113 (bit 2) = 1: Operation will be stopped.
Return to Library 2 PARAMETER USER Classification Address Display title Meaning EIA/ISO Description Select whether the maximum available wear offset data Y on the TOOL DATA display is to be included in the life judgment items listed for the tool life management function. Tool life management – Maximum available wear offset data Y F113 F113 (bit 6) = 0: The maximum available wear offset data Y will be included in the life judgment items.
Return to Library PARAMETER USER Classification Address EIA/ISO Display title Meaning 2 Description Tool shape check during tool measurement F114 (bit 2) = 0: During measurement for IN and EDGE tools, alarm 653 ILLEGAL TOOL DESIGNATED occurs since the measurements are possible only at 0 degrees of the B-axis. — F114 F114 (bit 2) = 1: The shape of the tool is not checked.
Return to Library 2 PARAMETER USER Classification Address Display title Meaning EIA/ISO Description F114 (bit 6) = 0: Invalid. Initially, the G50-specified coordinate system is selected. F114 (bit 6) = 1: Valid. Initially, the MAZATROL coordinate system (G53.5) is selected. — F114 (bit 6) Program type M, E Conditions Immediate Unit — Setting range 0, 1 F114 (bit 7) = 0: The life of the tool is judged from its machining count.
Return to Library PARAMETER USER Classification Address Display title Meaning 2 EIA/ISO Description Specify the Y-axial feed rate for the runout of the threading cycle. Feed rate of the threading runout – Y-axis F117 Program type M, E Conditions Immediate Unit 1 mm/min Setting range 0 to 240000 Specify the Z-axial feed rate for the runout of the threading cycle.
Return to Library 2 PARAMETER USER Classification Address Display title Meaning EIA/ISO Description Specify the Y-axial clamping speed for the threading cycle. Clamping speed for the threading cycle – Y-axis F121 Program type M, E Conditions Immediate Unit 1 mm/min Setting range 0 to 99999999 Specify the Z-axial clamping speed for the threading cycle.
Return to Library PARAMETER USER Classification Address Display title Meaning 2 EIA/ISO Description The data input in the following items are checked based on the permissible data alteration amount set in this parameter. Permissible data alteration amount 2 for input error prevention function F125 Program type M, E Conditions Immediate Unit — Setting range 0 to 99999999 TOOL DATA: WEAR COMP. X, WEAR COMP. Y, WEAR COMP. Z TOOL OFFFSET: WEAR COMP.
Return to Library 2 PARAMETER USER Classification Address EIA/ISO Display title Meaning Description Specify tool-drawing accuracy in the solid mode of the TOOL PATH CHECK display. As the specified value is greater (maximum value: 9), accuracy increases progressively.
Return to Library PARAMETER USER Classification Address Display title Meaning 2 EIA/ISO Description Specify for the solid mode of the TOOL PATH CHECK display the amount of C-axial angle offset for the jaws displayed automatically. Angle offset for the jaws displayed in solid mode for the No. 1 turning spindle F139 Program type M Conditions Immediate Unit 0.
Return to Library 2 PARAMETER USER Classification Address Display title Meaning EIA/ISO Description Invalid — F146 to F153 Program type — Conditions — Unit — Setting range — Parameter for system internal setting Setting prohibited — F154 Program type — Conditions — Unit — Setting range — Invalid — F155 to F160 Program type — Conditions — Unit — Setting range — 2-146
Return to Library PARAMETER USER Classification Address 2 EIA/ISO Display title Meaning Description Lathing tool offset functions 76543210 Shape/wear offset number separation 0: Invalid 1: Valid Shape offset handling 0: Coordinate shift 1: Tool movement Tool offset timing 0: When move command is executed following Tcode command 1: When T-code command is executed Tool offset vector handling if reset function is executed 0: Vector cleared 1: Vector not cleared Shape offset handling if offset number
Return to Library 2 PARAMETER USER Classification Address EIA/ISO Display title Meaning Description 76543210 During independent start of tool tip point control 0: Movement according to the particular amount of offset 1: No movement according to the particular amount of offset Type of passage of tool tip point through singular point Chamfer/corner R-command address selection 0: (I), (K), (R), (,R), (,C), (,A) 1: (R), (C), (A) Fixed hole-machining cycle return selection 0: Initial point 1: R-point 6
Return to Library PARAMETER USER Classification Address Display title Meaning 2 EIA/ISO Description 76543210 Bar feeder scheduling function 0: Invalid 1: Valid Incorporation of wear offset data into the current position display in EIA/ISO program mode 0: Invalid 1: Valid Incorporation of wear offset data into the current position display in MAZATROL program mode 0: Valid 1: Invalid Position of thread turning tool nose on solid drawing 0: Tool tip 1: Position measured using TOOL EYE Barrier check on
Return to Library 2 PARAMETER USER Classification Address Display title Meaning EIA/ISO Description 76543210 High-speed synchronous tapping function 0: Valid 1: Invalid X-axis movement to minus side during polar coordinate interpolation 0: Enabled 1: Disabled C-axis indexing when EIA subprogram is called from MAZATROL program 0: Not executed 1: Executed Modal or non-modal state of Q command in deep hole drilling cycle 0: Modal 1: Non-modal Conversion of tool set data for milling tool based on head
Return to Library PARAMETER USER Classification Address Display title Meaning 2 EIA/ISO Description 76543210 Alteration of tool set value (tool length) on the TOOL DATA display in the automatic operation mode 0 : Enabled 1 : Disabled — F166 Program type M Conditions After stop of movement Unit Bit Setting range Binary, eight digits Type of wear offset indicated in the milling tool list on the TOOL DATA display 0 : Cutting edge offset 1 : Wear offset ID No.
Return to Library 2 PARAMETER 2-3-5 User parameter SOFT LIMIT (I) USER Classification Display title Meaning Address SOFT LIMIT Description Shift amount of unidirectional positioning (G60) The amount and direction of shift from the final setting position during unidirectional positioning of the point-machining or during execution of G60.
Return to Library PARAMETER USER Classification SOFT LIMIT Display title Meaning Address Description Invalid — I4 Program type — Conditions — Unit — Setting range — Override (%) Function for making the G0 speed variable 100 Variable override: Minimum value I5 Program type M, E Conditions Immediate Unit % Setting range 0 to 100 I5 0 I9 I7 I7 Axis position I7 Axis position I10 Invalid — I6 Program type — Conditions — Unit — Setting range — Override (%) Function
Return to Library 2 PARAMETER USER Classification SOFT LIMIT Display title Meaning Address Description Invalid — I8 Program type — Conditions — Unit — Setting range — Override (%) Function for making the G0 speed variable Variable control area lower limit 100 I9 Program type M, E Conditions Immediate Unit 0.0001 mm/0.00001 inch/ 0.
Return to Library PARAMETER USER Classification Display title Meaning Address 2 SOFT LIMIT Description Set the clamping value for the amount of handle interruption. Clamping value for the amount of handle interruption I12 Program type M, E Conditions Immediate Unit 0.001 mm 0.0001 inch 0.
Return to Library 2 PARAMETER USER Classification Display title Meaning Address SOFT LIMIT Description Invalid — I15 to I24 Program type — Conditions — Unit — Setting range — 2-156
Return to Library PARAMETER 2-3-6 User parameter SYSTEM (SU) USER Classification Address SYSTEM Display title Meaning Description Set the reference axis of abscissa. Reference axis of abscissa for plane selection SU1 Program type M, E Conditions After stop of movement Unit — Setting range 0 to 255 Set axis 1 parallel to the axis of abscissa.
Return to Library 2 PARAMETER USER Classification Address Display title Meaning SYSTEM Description Set axis 1 parallel to the axis of ordinate. Axis 1 parallel to the axis of ordinate for plane selection SU5 Program type M, E Conditions After stop of movement Unit — Setting range 0 to 255 Set axis 2 parallel to the axis of ordinate (cylindrical interpolation).
Return to Library PARAMETER USER Classification Address Display title Meaning SYSTEM Description Set axis 2 parallel to the height axis.
Return to Library 2 PARAMETER USER Classification Address SYSTEM Display title Meaning Description Selection of tool change position specification code Specify tool change position from [0] through [8] below.
Return to Library PARAMETER USER Classification Address 2 SYSTEM Display title Meaning Description Specify the types of axes to be simultaneously moved when approaching the tool to the next machining area. Movement of axes during approach 0: Three axes (X, Y, Z) move at the same time. 1: After Z-axis movement, the X-axis and the Y-axis move at the same time.
Return to Library 2 PARAMETER USER Classification Address SYSTEM Display title Meaning Description Specify the name of the axis used as the thrust axis for the W-axis. Name of thrust axis for W-axis SU15 Program type E Conditions After stop of movement Unit — Setting range &41 to &5A 0: The tool moves to the approach position set in the machining program, without moving to the indexed swivel position.
Return to Library PARAMETER USER Classification Address 2 SYSTEM Display title Meaning Description Tool turning clearance is required to prevent interference between the tool and stock material during tool change in automatic operation. SU51 Tool turning clearance (radial value) in Xaxis Chuck SU50 SU50 Stock material shape Program type M Conditions Immediate Unit 0.001 mm/0.
Return to Library 2 PARAMETER USER Classification Address SYSTEM Display title Meaning Description Set the position where the turret is to be retracted for the turret retraction function. Specify coordinates in the machine coordinate system based on the machine zero point.
Return to Library PARAMETER USER Classification Address 2 SYSTEM Display title Meaning Description If a cutting depth has not been specified in the program, operation will occur in accordance with the setting of this parameter. Cutting depth in the composite-type fixed cycle (G271/G272, G71/G72) SU103 SU103 Program type E Conditions Immediate Unit 0.0001 mm/0.
Return to Library 2 PARAMETER USER Classification Address SYSTEM Display title Meaning Description Set the spindle safety clamp speed of a tool whose diameter (nominal diameter) is not specified in the tool data. This clamp speed is invalid for the tools with tool diameter (or nominal diameter, if diameter cannot be specified) setting in the tool data.
Return to Library PARAMETER USER Classification Address 2 SYSTEM Display title Meaning Description - If the command block of G284/G288 (machining G-codes, F30 = 0) or of G84/G88 (turning G-codes, F30 = 1) does not contain spindle forward/reverse rotation M-codes, one of the following M-codes will be output, depending on the status of bit 0 in parameter SU153: SU153 bit 0 BA59 = 3 BA60 = 4 BA59 = 203 BA60 = 204 0 Tapping cycle of turning Tapping cycle of milling 1 Inverse tapping cycle of tu
Return to Library 2 PARAMETER 2-3-7 User parameter TURNING (TC) USER Classification Address TURNING Display title Meaning Description Cut depth can be reduced as remaining workpiece thickness becomes less in rough cutting in bar machining unit, corner machining unit, and copy machining unit.
Return to Library PARAMETER USER Classification Address 2 TURNING Display title Meaning Description a F3 b F1 Deceleration rate in down-going taper for rough cutting in bar machining unit TC5 NM211-00264 Program type M Conditions Immediate Unit % Setting range 0 to 500 F 3 = F1 × TC5 × 100 F1 : Feed rate for rough cutting F3 : Reduced feed rate a b This is effective only when TC141 (bit 0) = 1.
Return to Library 2 PARAMETER USER Classification Address TURNING Display title Meaning Description PS [1] [2] Rough cutting residue ratio in cutting off cycle in groove cutting unit PS : Programmed start point PE : Programmed end point l l : Groove machining depth l = PS・PE d d : Rough cutting residue PE TC9 d=l× TC9 100 NM211-00267 Program type M Conditions Immediate Unit % Setting range 0 to 100 [1] Cutting at rough cutting feed rate to a point short of end point PE by dista
Return to Library PARAMETER USER Classification Address 2 TURNING Display title Meaning Description TC12 F’ = F × 100 F : Specified feed rate F' : Feed rate at cutting start Programmed end point Programmed start point End point Deceleration rate at cutting end in turningdrilling unit θ Drill D TC12 l Feed rate at F' to the point distant by l from the end point l= Program type M Conditions Immediate Unit % Setting range 0 to 100 D D + 10 2 × tanθ/2 D l = 10 NM211-00269 (0° < θ
Return to Library 2 PARAMETER USER Classification Address TURNING Display title Meaning Description This parameter is valid during initial cutting in a bar roughing cycle. If the remainder obtained by dividing the thickness of cutting during the roughing cycle by the corresponding cutting depth stays within the range specified by this parameter, that value will be added to the initial cutting depth to reduce the cutting repeat times. Example 1: TC14 = 0 (R-depth.
Return to Library PARAMETER USER Classification Address 2 TURNING Display title Meaning Description Set the starting pitch error rate of threading. [1] Pitch error correction during threading acceleration TC17 Program type M Conditions Immediate Unit 0.
Return to Library 2 PARAMETER USER Classification Address TURNING Display title Meaning Description TC21 Programmed 10 end point P : Tapping pitch l : Incomplete thread portion length l=P× Incomplete threading portion length calculation coefficient for turning-tap tip TC21 Programmed start point Tap l Program type M Conditions Immediate Unit Pitch/10 Setting range 0 to 99 Cutting end point specified farther by this length l NM211-00273 T C22 l = P × 10 Turning-tapper elongation cal
Return to Library PARAMETER USER Classification Address 2 TURNING Display title Meaning Description TC25 h = P × 10000 Thread height calculation coefficient for outside diameter, face/rear thread cutting (inch) h : Thread height P : Thread pitch TC25 Program type M Conditions Immediate Unit 0.
Return to Library 2 PARAMETER USER Classification Address TURNING Display title Meaning Description <#4> P Recessing width for #4 TC30 TC29 TC29 Program type NM211-00280 M Conditions Immediate Unit 0.001 mm/0.0001 inch Setting range 0 to 65535 P: Programmed end point Recessing depth for #4 TC30 Program type M Conditions Immediate Unit 0.001 mm/0.0001 inch Setting range 0 to 65535 <#5> TC32 Recessing width for #5 TC31 Program type M Conditions Immediate Unit 0.
Return to Library PARAMETER USER Classification Address 2 TURNING Display title Meaning Description <#6> Recessing width for #6 TC33 TC33 P TC34 Program type M Conditions Immediate Unit 0.001 mm/0.0001 inch Setting range 0 to 65535 TC34 TC33 P: Programmed end point Recessing depth for #6 TC34 Program type M Conditions Immediate Unit 0.001 mm/0.
Return to Library 2 PARAMETER USER Classification Address TURNING Display title Meaning Description Safety contour clearance ― Outside diameter clearance (radial value) TC37 Safety contour clearance is provided for outside of the stock material shape specified by common data in program. Tool approach and escape paths for each unit will be automatically determined according to set data (outside diameter, inside diameter, front clearance, back clearance) for parameters from TC37 to TC40.
Return to Library PARAMETER USER Classification Address 2 TURNING Display title Meaning Description Thread cutting clearance is provided to specify tool return distance for each cycle in thread cutting unit. Thread cutting clearance will be added to the highest portion of thread and repeating path will be determined automatically.
Return to Library 2 PARAMETER USER Classification Address TURNING Display title Meaning Description Groove cutting clearance is provided at machining start portion in groove cutting unit. Tool path Outside diameter clearance TC37 TC42 Groove cutting clearance (radial value) in X-axis TC42 NM211-00226 Front clearance TC39 Tool path TC42 Program type M Conditions Immediate Unit 0.001 mm/0.
Return to Library PARAMETER USER Classification Address 2 TURNING Display title Meaning Description Workpiece transfer clearance is provided to specify workpiece transfer position in workpiece transfer unit. Workpiece transfer clearance No. 1 spindle No. 2 spindle Workpiece TC44 TC44 Workpiece transfer position Program type M Conditions Immediate Unit 0.001 mm/0.0001 inch Setting range 0 to 65535 NM211-00231 No.
Return to Library 2 PARAMETER USER Classification Address TURNING Display title Meaning Description TC47 TC47 TC47 G1 Pecking return distance in turning-drilling unit G0 TC47 P2 Program type M Conditions Immediate Unit 0.001 mm/0.0001 inch Setting range 0 to 65535 P1 D4 D3 D2 D1 P1: Start point P2: End point Dn (n = 1 to 4) = Cut depth NM211-00252 Minimum turning-drilling cut depth is set.
Return to Library PARAMETER USER Classification Address 2 TURNING Display title Meaning Description The staring feed value for cutting-off is a feed value that has been designated in unit data, and the ending feed value for cutting-off is a feed value that has been designated in sequence data. The feed rate from the start of machining to the end is reduced in steps according to the number of times that has been designated here. Example: Feed rate set at feed item in unit data = 0.
Return to Library 2 PARAMETER USER Classification Address TURNING Display title Meaning Description For escape by very short distance, G01 feed speed will be faster than G00 to complete the operation. (If G00 is used, smoothing 0 detection will be made at the end position.) Therefore, for escape very short distance, use G01 command, and set the feed speed of this command as parameter.
Return to Library PARAMETER USER Classification Address 2 TURNING Display title Meaning Description Example: Outside diameter machining in normal (– Z-axis) direction dr: Reverse feed contour data Reverse feed tolerance for contour machining Contour TC55 dr Program type M Conditions Immediate Unit 0.001 mm/0.0001 inch Setting range 0 to 65535 NM211-00243 dr ≤ TC55 ........ No alarm dr > TC55 ........
Return to Library 2 PARAMETER USER Classification Address TURNING Display title Meaning Description Example: Workpiece transferred from No. 1 spindle to No. 2 spindle TC57 Workpiece Workpiece pressing speed in workpiece transfer unit No. 2 spindle No. 1 spindle Workpiece transfer clearance (TC44) TC57 Workpiece transfer position specified in transfer display NM211-00236 Set this parameter equal to or as close as possible to its standard value. Excessive setting may cause a contact error.
Return to Library PARAMETER USER Classification Address Display title Meaning 2 TURNING Description Invalid — TC60 Program type — Conditions — Unit — Setting range — Simultaneous operation pattern for transfer of workpieces between two unit jobsites TC61 = 1: Rotation of the spindle and movement of the Z-axis Simultaneous operation pattern for transfer TC61 = 2: Orientation of the spindle and movement of the Z-axis TC61 TC61 = 4: Positioning of the C-axis and movement of the Z-axis Pr
Return to Library 2 PARAMETER USER Classification Address TURNING Display title Meaning Description When a FLASH tool is used, specify the position for indexing the tool, namely, the tool change position for indexing the tool of the same TNo. at the same B-axis angle during programmed operation. Selection of tool change position specification code for FLASH tool In all other cases, the tool change position specified by SU10 becomes valid.
Return to Library PARAMETER USER Classification Address 2 TURNING Display title Meaning Description Set the amount of relief after executing the TRANSFER unit. Example: Transfer from HD2 to HD1 Amount of relief after transfer using the TRANSFER unit (Spindle mode 0 to 5) HD1 HD2 TC63 Workpiece Program type M Conditions After stop of movement Unit 0.1 mm/0.
Return to Library 2 PARAMETER USER Classification Address TURNING Display title Meaning Description Example 1: Standard type cutting Prior to cutting up along the wall in the end of final cycle, escape will be made by specified distance. TC67 Return distance (radial value) in X-axis at wall during rough cutting in bar cutting unit or in corner machining unit of MAZATROL programs TC67 Program type M Conditions Immediate Unit 0.001 mm/0.
Return to Library PARAMETER USER Classification Address 2 TURNING Display title Meaning Description Specify the feed stopping rotation dwell time during the chip cutting cycle. Feed is stopped while the spindle rotates for the specified time. Feed stopping rotation dwell time during the chip cutting cycle (valid only for roughing) TC71 Program type M Conditions Immediate Unit Revolutions Setting range 0 to 65535 Note: If “0” is entered, the dwell time will be handled as “0”.
Return to Library 2 PARAMETER USER Classification Address TURNING Display title Meaning Description Tool Pecking return distance in groove cutting unit and grooving (G274/G275, G74/G75) TC74 TC74 Program type M, E Conditions Immediate Unit 0.001 mm/0.0001 inch Setting range 0 to 65535 NM211-00248 d d: Tool diameter l : Groove width Tool Overlap distance for machining wide groove in groove cutting unit TC75 TC75 Program type M Conditions Immediate Unit 0.001 mm/0.
Return to Library PARAMETER USER Classification Address 2 TURNING Display title Meaning Description Cut depth (diametral value) for final cut in thread cutting unit TC78 Cut depth (diametral value) for final cut in composite-type thread cutting cycle G276 1st cut (n/2-1)th cut (n/2)th cut Program type M, E Conditions Immediate Unit 0.001 mm/0.
Return to Library 2 PARAMETER USER Classification Address TURNING Display title Meaning Description L2 L1 L End point Start point ψ NM211-00272 Chamfering data calculation coefficient in thread cutting unit and thread cutting cycle (G276/G292, G76/G92) TC82 L L1 L2 ψ L2 = L0 × : : : : Effective thread length Same pitch incomplete thread length (follow-up delay) Chamfering data Chamfering angle TC82 10 L0 : Thread lead Program type M, E Conditions Immediate Unit Lead/10 Setting
Return to Library PARAMETER USER Classification Address 2 TURNING Display title Meaning Description Specify the feed rate to be auto-set for finishing (turning) in the MAZATROL program. Feed rate to be auto-set for finishing TC84 Program type M Conditions Immediate Unit 0.001 mm/0.0001 inch Setting range 0 to 65535 Specify the number of the magazine pocket holding the adapter for the long boring bar.
Return to Library 2 PARAMETER USER Classification Address Display title Meaning TURNING Description Specify the sequence of the returning operation set in the ATC and RETURN items in the END unit for machines with the lower turret. Returning operation after machining specified in the END unit TC98 TC98 = 0: The upper and lower turrets return simultaneously. TC98 = 1: The upper turret returns prior to the lower turret. TC98 = 2: The lower turret returns prior to the upper turret.
Return to Library PARAMETER USER Classification Address Display title Meaning TURNING Description Select a cycle counter sampling axis. Selection of cycle counter sampling axis (For detecting imbalance) TC102 Program type E Conditions At power on Unit — Setting range 0 to 16 Set the amplitude limit of table vibration.
Return to Library 2 PARAMETER USER Classification Address TURNING Display title Meaning Description Specify the maximum outside diameter range of the workpieces displayed on the CUTTING CONDITON LEARN display. TC114 to TC116 CUTTING CONDITON LEARN display — Max. workpiece outside diameter range Program type Specify the range so that the relational expression of TC114 < TC115 < TC116 is established. M Conditions Immediate Unit 1 mm/0.
Return to Library PARAMETER USER Classification Address 2 TURNING Display title Meaning Description Specify the distance from the B-axis rotational center of the milling spindle to the front end of the long boring bar.
Return to Library 2 PARAMETER USER Classification Address TURNING Display title Meaning Description TC141 (bit 0) = 0: Disuse F1 F1 No acceleration TC141 (bit 0) = 1: Use TC141 (bit 0) Use/disuse of acceleration in up-going slope during rough cutting cycle in bar machining unit F2 F1 F 2 > F1 F1 : Feed rate for rough cutting cycle F2 : Feed rate after acceleration NM211-00208 Program type M Conditions Immediate Unit — Setting range 0, 1 (!TC2, TC3) TC141 (bit 1) = 0: Disuse F1
Return to Library PARAMETER USER Classification Address 2 TURNING Display title Meaning Description TC141 (bit 2) = 0: Disuse Alarm not caused even if acceleration distance at start of thread cutting unit exceeds clamp data TC141 (bit 2) = 1: Use Alarm caused when acceleration distance at start of thread cutting unit exceeds clamp data Example: Lc TC141 Selection between use/disuse of acceleration distance check at start of thread cutting unit → Alarm not caused Lo → Alarm caused (bit 2)
Return to Library 2 PARAMETER USER Classification Address TURNING Display title Meaning Description An angle margin for nose shape compensation can be selected by setting data in bits 4 and 5. TC141 Selecting an angle margin for nose shape compensation Setting (bit 4) (bit 5) Program type M Conditions Immediate Unit — Setting range 0, 1 Bit 5 Bit 4 Angle margin for nose shape compensation 0 0 3.0 0 1 2.0 1 0 1.0 1 1 0.5 TC141 (bit 6) = 1 A name can be selected.
Return to Library PARAMETER USER Classification Address TC142 TURNING Display title Meaning 2 Description Selecting an inter-unit relief path when a succession of I.D.
Return to Library 2 PARAMETER USER Classification Address TURNING Display title Meaning Description TC142 (bit 5) = 0: An alarm will not be issued even if the ending position of workpiece pressing is reached during the transfer of the workpiece.
Return to Library PARAMETER USER Classification Address Display title Meaning 2 TURNING Description 76543210 Automatic selection of the relief path for the continuous I.D.
Return to Library 2 PARAMETER 2-3-8 User parameter SOLID (SD) USER Classification Meaning Address SOLID Display title Description Invalid — SD1 to SD48 Program type — Conditions — Unit — Setting range — Set the type of coordinate system used for position display. 0: MAZATROL coordinate system 1: Machine coordinate system Machine coordinate system setting SD49 Program type M, E Conditions Immediate Unit — Setting range 0, 1 Select a table type for 3D setup display.
Return to Library PARAMETER USER Classification Display title Meaning Address 2 SOLID Description Set the default value for the model’s movement distance per time that is to be displayed in the movement distance assignment dialog box. Distance of the model movement per time SD97 Program type M, E Conditions Immediate Unit 0.0001 mm/0.
Return to Library 2 PARAMETER 2-3-9 Machine parameter CALL MACRO (J) MACHINE Classification CALL MACRO Display title G-code macroprogram call No.1 No.2 No.3 No.4 No.5 No.6 No.7 J1 J2 J5 J6 J9 J13 J17 J21 J25 J10 J14 J18 J22 J26 J3 J7 J11 J15 J19 J23 J27 J4 J8 J12 J16 J20 J24 J28 No.8 No.9 No.
Return to Library PARAMETER MACHINE Classification Address Display title Meaning CALL MACRO Description Invalid — J81 to J90 Program type — Conditions — Unit — Setting range — Parameter for system internal setting Setting prohibited — J91 to J107 Program type — Conditions — Unit — Setting range — Invalid — J108 to J144 Program type — Conditions — Unit — Setting range — 2-209 2
Return to Library 2 PARAMETER 2-3-10 Machine parameter MEASURE (K) MACHINE Classification Address MEASURE Display title Meaning Description Distance from the center of the C-axis (spindle) to the nose of the tool Z Tool K1 Rotational radius of the C-axis X Spindle center K1 K1 Y Program type E Conditions Immediate Unit Setting range 0.0001 mm/0.
Return to Library PARAMETER MACHINE Classification Address MEASURE Display title Meaning Description Identification number of the shaping control axis Specify the shaping control axis as follows: Example: Set “4” for a three-axis machine. Set “5” for a four-axis machine. Shaping control axis Note: Set the type of the axis which has been set on this parameter to the rotational axis (M17 bit 4 = 1).
Return to Library 2 PARAMETER MACHINE Classification Address MEASURE Display title Meaning Description Fixed value (0) K10 Program type — Conditions — Unit — Setting range — Set this parameter to change the display language.
Return to Library PARAMETER MACHINE Classification Address 2 MEASURE Display title Meaning Description (1) Workpiece measurement Sensor path fa K13 Measurement skip feed rate (X-axis, Z-axis) Workpiece K13 Measurement stroke (K19) Program type M Conditions Immediate Unit 1 mm/min / 0.
Return to Library 2 PARAMETER MACHINE Classification Address MEASURE Display title Meaning Description Specification of measuring tolerance (lower limit) K17 Program type M, E Conditions Immediate Unit % Setting range 0 to 100 (1) Tool compensation will be made in cases below. a1 – a2 a – a2 × K18 ≥ Compensation data ≥ 1 × K17 100 100 a – a2 a – a2 – 1 × K17 ≥ Compensation data ≥ – 1 × K18 100 100 (2) Tool compensation will not be made in cases below.
Return to Library PARAMETER MACHINE Classification Address 2 MEASURE Display title Meaning Description During approach operation to measurement start point, if touch sensor is actuated, the C-axis will rotate by angle determined by the measurement object shape angle and setting value K21.
Return to Library 2 PARAMETER MACHINE Classification Address Display title Meaning MEASURE Description 1. Delays master/slave axis position matching during automatic error correction (parameter K103 bit 1 = 0). 2. Delays pitch error correction data output when the servo is ON. Simultaneous control: Delay counter for automatic correction of synchronizing errors K29 Program type K30 to K33 M, E Conditions Immediate Unit × 1.
Return to Library PARAMETER MACHINE Classification Address MEASURE Display title Meaning 2 Description The upper-limit value of the feed rates available while the external deceleration signal is ON Feedrate External deceleration speed K37 K37 Program type M, E Conditions After stop of movement Unit 1 mm/min Setting range 0 to 120000 Work number called during S-code macroprogram appointment ON External deceleration signal MPL508 The work number of the macroprogram to be called during S-
Return to Library 2 PARAMETER MACHINE Classification Address Display title Meaning MEASURE Description The feed rate during axis movement by G31 (skip function) If the same block as that of G31 contains an F command, then that feed rate becomes valid. G31 skipping speed K41 Program type M, E Conditions After stop of movement Unit 1 mm/min Setting range 0 to 120000 The feed rate during axis movement by G31.1 (multi-step skip function) If the same block as that of G31.
Return to Library PARAMETER MACHINE Classification Address Display title Meaning 2 MEASURE Description The feed rate during axis movement by G31.4 (skip function) If the same block as that of G31.4 contains an F command, then that feed rate becomes valid. G31.4 skipping speed K45 Program type E Conditions After stop of movement Unit 1 mm/min Setting range 0 to 120000 Set the excessive pressing error spread (the amount of drooping).
Return to Library 2 PARAMETER MACHINE Classification Address Display title Meaning MEASURE Description Set the first number of the M-codes to be used for the M-code standby function. First number of the standby M-codes Example: To use M950 to M995 as the standby M-codes set “950” in K49 and “46” in K50. K49 Program type M, E Conditions After stop of movement Unit — Setting range 31 to 1000 Set the total number of M-codes to be used for the M-code standby function.
Return to Library PARAMETER MACHINE Classification Address 2 MEASURE Display title Meaning Description Set the type of vocal output language.
Return to Library 2 PARAMETER MACHINE Classification Address MEASURE Display title Meaning Description This parameter is used during S-code macroprogram appointment to select the method of calling the macroprogram whose work number has been set using the K38 parameter. Type of S-code macroprogram appointment call Setting K57 Program type M, E Conditions Immediate Unit — Setting range 0 to 3 Calling method 0 M98 P"""" 1 G65 P"""" 2 G66 P"""" 3 G66.
Return to Library PARAMETER MACHINE Classification Address Display title Meaning MEASURE Description Fixed value (1) K61 Program type — Conditions — Unit — Setting range — Fixed value (1) K62 Program type — Conditions — Unit — Setting range — Fixed value (1) K63 Program type — Conditions — Unit — Setting range — Fixed value (2) K64 Program type — Conditions — Unit — Setting range — 2-223 2
Return to Library 2 PARAMETER MACHINE Classification Address Display title Meaning MEASURE Description Fixed value (1) K65 Program type — Conditions — Unit — Setting range — Fixed value (1) K66 Program type — Conditions — Unit — Setting range — Fixed value (1) K67 Program type — Conditions — Unit — Setting range — Invalid — K68 Program type — Conditions — Unit — Setting range — 2-224
Return to Library PARAMETER MACHINE Classification Address MEASURE Display title Meaning Description 76543210 (0: Invalid 1: Valid) SKIP-2 G31.1 skip conditions SKIP-10 K69 HR353 SKIP-3 Program type E Conditions After stop of movement Unit Bit Setting range Binary, eight digits Select the skip signal for G31.1 command. 76543210 (0: Invalid 1: Valid) SKIP-2 G31.
Return to Library 2 PARAMETER MACHINE Classification Address MEASURE Display title Meaning Description 7654321 (0: Invalid 1: Valid) SKIP-2 G4 skip conditions SKIP-10 K73 QX721 SKIP-3 Program type E Conditions After stop of movement Unit Bit Setting range Binary, eight digits Emergency stop contactor cutoff time (Safety supervisory function) K74 Program type M, E Conditions After stop of movement Unit sec Setting range 0 to 60 Select the skip signal for G4 command.
Return to Library PARAMETER MACHINE Classification Address Display title Meaning 2 MEASURE Description Enter the device number of the remote I/O device to be activated to input a door open/closed status signal. The device of the entered serial device number will be reserved according to the particular setting of K78 (the parameter for setting the number of door switches). Door switch input device (Safety supervisory function) Note: Door switch input will be invalid if “&0” is entered.
Return to Library 2 PARAMETER MACHINE Classification Address Display title Meaning MEASURE Description If the setting of K85 is from 1 to 3 msec, this setting will be used as the linear acceleration/deceleration time constant for the G32 threading block. Special linear acceleration/deceleration time constant for threading If the setting is outside the valid range, however, the normal linear acceleration/deceleration time constant for G01 will be used.
Return to Library PARAMETER MACHINE Classification Address Display title Meaning MEASURE Description Specify an alternative M-code for M97 when user macro interruption is valid.
Return to Library 2 PARAMETER MACHINE Classification Address Display title Meaning MEASURE Description 76543210 Fixed value (0) Tool position compensation during T-command execution 0: Not performed 1: Performed Coordinate system update during handle pulse interrupt 0: Not performed 1: Performed — Fixed value (0) Acceleration/deceleration time constant for handle pulse feed 0: Time constant for cutting feed 1: No time constant K95 Software limits for G30 execution 0: Invalid 1: Valid In-position
Return to Library PARAMETER MACHINE Classification Address Display title Meaning MEASURE Description Specify the name of the axis to be made parallel with respect to the direction of the spindle when the angle of the B-axis is 0 degrees. B-axis misalignment correction Name of parallel axis K97 Program type M, E Conditions Immediate Unit Hexadecimal, two digits Setting range &41 to &5A Note: If 0 is entered, the axis will be regarded as the Z-axis (&5A).
Return to Library 2 PARAMETER MACHINE Classification Address Display title Meaning MEASURE Description Specify the name of the axis to be made orthogonal with respect to the rotational plane of the rotational axis to undergo dynamic offset.
Return to Library PARAMETER MACHINE Classification Address Display title Meaning 2 MEASURE Description 76543210 Output of a laser measurement B-axis 0-degree command after ATC 0: Output invalid 1: Output valid Direction of the laser axis of the laser measuring instrument 0: Depends on the setting of parameter L16. L16 = 1: Parallel to the Y-axis, L16 = 2: Parallel to the X-axis 1: Depends on the setting of bit 2 in parameter K104.
Return to Library 2 PARAMETER MACHINE Classification Address Display title Meaning MEASURE Description 76543210 Execution conditions for user macroprogram interrupt 0: Edge triggering (Performed just once when the interrupt signal is turned ON) 1: Status triggering (Repeatedly performed while the interrupt signal is ON) Start timing for user macroprogram interrupt 0: The block under execution is aborted and then the interrupt occurs immediately.
Return to Library PARAMETER MACHINE Classification Address Display title Meaning 2 MEASURE Description Invalid — K109 Program type — Conditions — Unit — Setting range — Set the judgment angle near a singular point. The setting, if 0, will be handled as 1 deg. Judgment angle near a singular point (Tool tip point control) K110 Program type E Conditions After stop of axis movement Unit deg Setting range 0 to 360 Set the clamping speed (speed command) in safety supervisory mode 3.
Return to Library 2 PARAMETER MACHINE Classification Address MEASURE Display title Meaning Description Set the type of machine.
Return to Library PARAMETER MACHINE Classification Address Display title Meaning MEASURE Description Set the axis number of the height axis in the rectangular coordinate system. A setting of 0 is invalid. Axis number of the height axis in the rectangular coordinate system (Tool tip point control) K116 Program type E Conditions Immediate Unit — Setting range 0 to 16 12: 2nd rotary axis ...... Rotates about horizontal axis, 1st rotary axis ....... Rotates about vertical axis.
Return to Library 2 PARAMETER MACHINE Classification Address Display title Meaning MEASURE Description Horizontal axis rotational center offset of the first rotary axis (Tool tip point control) K122 Set the distance from the rotational center of the tool control rotary axis (at the tool side) in the direction of the horizontal axis to the rotational center of the tool control rotary axis (at the opposite side).
Return to Library PARAMETER MACHINE Classification Address Display title Meaning 2 MEASURE Description K126 Horizontal axis rotational center offset of the second rotary axis (Tool tip point control) Program type E Conditions Immediate Unit 0.0001 mm Setting range ±99999999 Set the distance from the spindle holder end in the direction of the horizontal axis to the rotational center of the tool control rotary axis (at the tool side).
Return to Library 2 PARAMETER 2-3-11 Machine parameter TABLE (L) MACHINE Classification Address TABLE Display title Meaning Description The eccentricity of the stylus of the touch sensor with respect to the center of the spindle Touch sensor Stylus eccentricity of touch sensor (X-component) L1 +Z Stylus Program type M Conditions At power on Unit 0.0001 mm/0.
Return to Library PARAMETER MACHINE Classification Address 2 TABLE Display title Meaning Description The distance from the spindle taper gage line to the table surface, No.
Return to Library 2 PARAMETER MACHINE Classification Address TABLE Display title Meaning Description The maximum skipping movement distance for the measurement with the MMS unit An alarm message will appear if the touch sensor has not come into contact with the workpiece within this distance. Skipping stroke limit for MMS L8 Program type M, E Conditions Immediate Unit 0.0001 mm/0.00001 inch Setting range 0 to 99999999 Set to 1 when the machine of the random ATC specifications is used.
Return to Library PARAMETER MACHINE Classification Address 2 TABLE Display title Meaning Description Tolerance for Z coordinate value in circle measurement L12 Tolerance for measured coordinate value in face measurement Y Tolerance for manual measurement L12 L12 X MPL512 Program type M, E Conditions Immediate Unit 0.0001 mm/0.00001 inch Setting range 0 to ±99999999 Set the allowable angle for calculation of parallelism and right angle to be measured manually.
Return to Library 2 PARAMETER MACHINE Classification Address TABLE Display title Meaning Description Set macro program number for straightness measurement. Before shipment, the macro program is numbered “9999” at the factory.
Return to Library PARAMETER MACHINE Classification Address 2 TABLE Display title Meaning Description Invalid — L19 L20 Program type — Conditions — Unit — Setting range — Select the output type for the angle command of the indexing unit and the end unit of the MAZATROL program.
Return to Library 2 PARAMETER MACHINE Classification Address TABLE Display title Meaning Description Use L22 and L23 to set the dimensions of the sensor for tool nose measurement. L24 and L25 are provided to set in machine coordinates the reference point of the sensor (see the diagram below). [INTE IV, INTE e-HII, lathes] Example 1: For No.
Return to Library PARAMETER MACHINE Classification Address 2 TABLE Display title Meaning Description During manual TOOL EYE measurement, even if the sensor turns on for a time shorter than that which has been specified in this parameter, that will not be regarded as sensor-on. Timer setting for manual TOOL EYE measurement L27 Program type M, E Conditions Immediate Unit 3.
Return to Library 2 PARAMETER MACHINE Classification Address Display title Meaning TABLE Description Select for each machine model the appropriate case introduction messages on MACHINING NAVIGATION-PREDICTION display. Selection of machining navigation case introduction messages Specific data is preset for each machine model. Do not disturb the presettings.
Return to Library PARAMETER MACHINE Classification Address 2 TABLE Display title Meaning Description Specify the execution condition of the indexing unit. Execution of the indexing unit just before starting of machining of each tool sequence or at the end of each process: Selection of execution/non execution of indexing unit 0: 1: L39 Program type M Conditions At power on Unit — Setting range 0, 1 Won’t be made when the index angle is the same as the preceding indexing unit execution.
Return to Library 2 PARAMETER MACHINE Classification Address TABLE Display title Meaning Description Select showing or not showing of the index table angle on the POSITION display.
Return to Library PARAMETER MACHINE Classification Address 2 TABLE Display title Meaning Description Select preparation of next pallet or not to do so according to the pallet change mechanism. To prepare or not to prepare next pallet change 0: 1: Not to prepare next pallet To prepare next pallet L47 Program type M Conditions At power on Unit — Setting range 0, 1 Note: When this parameter is set to 1, it is possible to set the number of the next pallet in the pallet changing unit.
Return to Library 2 PARAMETER MACHINE Classification Address TABLE Display title Meaning Description Tool command system in MDI operation (Tool on the spindle and next time tool) 0: 1: Command of pocket number Command of group number Tool command system in MDI operation L51 Program type M Conditions Immediate Unit — Setting range 0, 1 Rewriting of machining management data with macro variable (system variable) Writing of machining management data with macro variable 0: 1: Impossible P
Return to Library PARAMETER MACHINE Classification Address 2 TABLE Display title Meaning Description 0: FR-SF 1: FR-SE Spindle load meter display type L55 Program type — Conditions At power on Unit — Setting range 0, 1 0: 1: 2: Method of measurement of coordinates by tool edge memorizing function (TEACH) Method by M2 tool edge memorizing function Method by M32 tool edge memorizing function (for Z-axis only) Method by M32 tool edge memorizing function (for X-, Y-, Z-axes) Example: +
Return to Library 2 PARAMETER MACHINE Classification Address TABLE Display title Meaning Description This parameter limits input items on the HEAD OFFSET display. 0: 1: Data just on item SPDL. CMD can be input. All data can be input.
Return to Library PARAMETER MACHINE Classification Address 2 TABLE Display title Meaning Description When FIXED is selected at the item RELAY in the face definition unit, the head arrives at the face for next machining through the point(s) specified by the parameters (to be set in the machine coordinates sytem). For AGX machines, the relay points (X1, Y1) and (X2, Y2) can be specified in the program (in the face definition sequence).
Return to Library 2 PARAMETER MACHINE Classification Address TABLE Display title Meaning Description After EIA/ISO subprogram execution; 0: 1: Return to head indexing point Z (Even if the T-code command is for the same tool.
Return to Library PARAMETER MACHINE Classification Address 2 TABLE Display title Meaning Description Specify the axes that simultaneously move from a machining face to the next machining face or in case of tool replacement. Axis movement from machining face on escapement 0: Two (three) axes simultaneously move to the safety position. 1: Y-axis (or X- and Y-axes) moves to the safety position after Z-axis moved.
Return to Library 2 PARAMETER MACHINE Classification Address Display title Meaning TABLE Description Set the cutting feed rate for pre-interpolational acceleration/deceleration control. Cutting feed rate for pre-interpolational acceleration/deceleration control L74 Program type M, E Conditions — Unit mm/min Setting range 1 to 999999 Set the time constant to obtain acceleration/deceleration of the cutting feed rate for pre-interpolational linear control.
Return to Library PARAMETER MACHINE Classification Address Display title Meaning 2 TABLE Description Invalid — L78 Program type — Conditions — Unit — Setting range — Set the In-position width for changeover of the synchronized-tapping gain. If 0 is set, 10 microns will be regarded as having been set. In-position width for changeover of the synchronized-tapping gain L79 Program type M, E Conditions At power on Unit 0.
Return to Library 2 PARAMETER MACHINE Classification Address TABLE Display title Meaning Description Set the thickness of the tilting table. This parameter is used for the software travel limit function provided to avoid collision between the spindle head and the tilting table (in its angular position from –90° to –120°). Table thickness L82 L82 Tilting table Program type M, E Conditions Immediate Unit 0.
Return to Library PARAMETER MACHINE Classification Address 2 TABLE Display title Meaning Description 2#Mx Correction value of alignment deviation X (0-degree face) 2#My L86 ey ex Program type M Conditions After stop of movement Unit 0.0001 mm/0.
Return to Library 2 PARAMETER MACHINE Classification Address TABLE Display title Meaning Description 2#Mx Correction value of alignment deviation X (180-degree face) 2#My L90 ey ex Program type M Conditions After stop of movement Unit 0.0001 mm/0.00001 inch Setting range 0 to ±99999999 Correction value of alignment deviation Y (180-degree face) L91 Program type M Conditions After stop of movement Unit 0.0001 mm/0.
Return to Library PARAMETER MACHINE Classification Address 2 TABLE Display title Meaning Description The X/Y travel distance can be set during the selection of EIAprogrammed fully automatic tool length measurement on the TOOL OFFSET display.
Return to Library 2 PARAMETER MACHINE Classification Address Display title Meaning TABLE Description Specify the muximum tool length for the MDI laser tool length measurement. Max. tool length for laser tool length measurement L98 Program type M, E Conditions At power on Unit 0.0001 mm/0.00001 inch Setting range 99999999 Specify the cycle time at which the operational status management data for the day is to be saved as a file on the hard disk.
Return to Library PARAMETER MACHINE Classification Address TABLE Display title Meaning Description [INTE e-HII] Approach point for tool diameter measurement L103: X L100: X Machine zero point L102: Z L100 Laser sensor position X L101 Laser sensor position Y L101: Y L102 Laser sensor position Z L100 to L105 L103 Approach point X for laser tool diameter measurement L104 Approach point Y for laser tool diameter measurement L98 L105 Approach point Z for laser tool length measurement L105: Z
Return to Library 2 PARAMETER MACHINE Classification Address TABLE Display title Meaning Description Select a rotational reference coordinate system for WPC-th.
Return to Library PARAMETER MACHINE Classification Address 2 TABLE Display title Meaning Description Select the timing to execute the workpiece and tool measurement. 0: The measurement unit is executed whenever the parts count reaches same or a multiple of the specified measurement interval in addition to the first time.
Return to Library 2 PARAMETER MACHINE Classification Address TABLE Display title Meaning Description Select whether the tailstock included in the tailstock-equipped machine specifications is of the conventional type or the motor-driven type. 0: 1: Conventional type Motor-driven type Tailstock type L107 (bit 2) Program type M, E Conditions Immediate Unit — Setting range 0, 1 Select whether the tail thrust is also to be displayed in pounds (lbs).
Return to Library PARAMETER MACHINE Classification Address 2 TABLE Display title Meaning Description 0: Does not operate the A-axis. 1: Returns the A-axis to its zero point.
Return to Library 2 PARAMETER MACHINE Classification Address TABLE Display title Meaning Description Vertically inverted spindle specifications — L110 (bit 1) Program type M, E Conditions Immediate Unit — Setting range 0, 1 Axis name of the secondary spindle 0: Z/C-axis 1: W/U-axis — L110 (bit 2) Program type M, E Conditions Immediate Unit — Setting range 0, 1 Specify whether to disable or enable the display of “section to be machined” in the milling tool sequence.
Return to Library PARAMETER MACHINE Classification Address Display title Meaning 2 TABLE Description Z-axis direction 0: Horizontal 1: Vertical — L110 (bit 7) Program type M, E Conditions Immediate Unit — Setting range 0, 1 Invalid — L111 L112 L113 to L116 L117 to L120 Program type — Conditions — Unit — Setting range — Interference check reference axis L113 1st set of axes L114 2nd set of axes L115 3rd set of axes L116 4th set of axes Program type M, E Conditions Immediate
Return to Library 2 PARAMETER MACHINE Classification Address L121 to L124 TABLE Display title Meaning Description Set the machine coordinate of the interference check target axis that is about to cause interference when the interference check reference axis is at its zero point.
Return to Library PARAMETER MACHINE Classification Address 2 TABLE Display title Meaning Description Invalid — L127 L128 Program type — Conditions — Unit — Setting range — This parameter functions as a filter to smoothen the waveform command specified for pre-interpolation acceleration/deceleration.
Return to Library 2 PARAMETER MACHINE Classification Address Display title Meaning TABLE Description Used for fully automatic tool measurement with a measuring table. Minimum usable tool diameter of the measurable chamfering tool L139 Program type — Conditions Immediate Unit 0.1 mm/0.01 inch Setting range 0 to 99.9 mm/9.
Return to Library PARAMETER 2-3-12 Machine parameter FEED VEL. (M) MACHINE Classification Address 2 FEED VEL.
Return to Library 2 PARAMETER MACHINE Classification Address FEED VEL. Display title Meaning Description The machine coordinating values of the point to which each axis is to move back under G28 command (first zero-point return). First zero point M4 Offset of machine coordinates system M4 Machine zero point Program type M, E Conditions At power on Unit 0.
Return to Library PARAMETER MACHINE Classification Address 2 FEED VEL. Display title Meaning Description The maximum moving zone permissible under the machine specifications Set the machine coordinate values. Example: +Y Maximum software limit specified by manufacturer (+ direction) M8 M8 (Y-axis) Program type M, E Conditions After stop of movement Unit 0.0001 mm/0.
Return to Library 2 PARAMETER MACHINE Classification Address FEED VEL. Display title Meaning Description Register the incremental axes respectively in hexadecimal numbers of the ASCII code. Coding of incremental axis M12 Program type M, E Conditions At power on Unit — Setting range &0 to &7F Specify the address name of the axes to be used for display, by the appropriate hexadecimal number of the ASCII code. For reverse display, set up the most significant bit.
Return to Library PARAMETER MACHINE Classification Address 2 FEED VEL. Display title Meaning Description Specify the name of the address to be used for axis name changing (G110), by the appropriate hexadecimal number of the ASCII code.
Return to Library 2 PARAMETER MACHINE Classification Address FEED VEL.
Return to Library PARAMETER MACHINE Classification Address FEED VEL.
Return to Library 2 PARAMETER MACHINE Classification Address FEED VEL. Display title Meaning Description Set an access inhibition area in the inclined-axis control software limit area consisting of the X-axis and the Yt-axis. - Parameters M25 and M26 are valid only for the X-axis and the Yt-axis. - If the X-axial and Yt-axial upper limits (M25) and lower limits (M26) are all zeros, the illegal axis area check function is invalid. - Use the parameter BA126 to select Type A or B (BA126 bit 1).
Return to Library PARAMETER MACHINE Classification Address 2 FEED VEL. Display title Meaning Description Set an access inhibition area in the inclined-axis control software limit area consisting of the X-axis and the Yt-axis. - Parameters M25 and M26 are valid only for the X-axis and the Yt-axis. - If the X-axial and Yt-axial upper limits (M25) and lower limits (M26) are all zeros, the illegal axis area check function is invalid. - Use the parameter BA126 to select Type A or B (BA126 bit 1).
Return to Library 2 PARAMETER MACHINE Classification Address Display title Meaning FEED VEL. Description Set the value that determines the maximum allowable value (Amax) of the acceleration that occurs between blocks. Amax = Optimum acceleration control (Target speed) M27 Program type M, E Conditions After stop of axis movement Unit mm/min Setting range 1 to 5000 M27 100 – N26 × 60 × 1000 × (mm/msec2) 100 N25 Note: If M27 = 0, M27 is regarded as equal to M1 (rapid feed rate).
Return to Library PARAMETER MACHINE Classification Address Display title Meaning 2 FEED VEL. Description Set the cutting feed clamping speed for superposition control. (Set value for the reference axis and superposition axis to be used during superposition control.
Return to Library 2 PARAMETER MACHINE Classification Address Display title Meaning FEED VEL. Description Set the safety clamping speed to be used in safety supervisory mode 3. In safety supervisory mode 3 and while a safety clamping request is in effect, operation decelerates to the set speed. (Assign a value smaller than that of parameter M33 to parameter M35.
Return to Library PARAMETER MACHINE Classification Address Display title Meaning 2 FEED VEL. Description Set the machine interference detection distances for the Intelligent Safety Shield. Set data so that the primary check distance is longer than the secondary check distance.
Return to Library 2 PARAMETER 2-3-13 Machine parameter TIME CONST. (N) MACHINE Classification Address TIME CONST. Display title Meaning Description Set the time constant to obtain linear acceleration/deceleration of the rapid feed rate. Speed M1 Rapid-feed time constant (linear acceleration/deceleration) N1 Time N1 N1 MPL523 Program type M, E Conditions Immediate Unit 1 msec Setting range 4 to 1800 Note: This parameter is valid only when bit 0 of M21 is 1.
Return to Library PARAMETER MACHINE Classification Address 2 TIME CONST. Display title Meaning Description Set the time constant for the filter that further smoothens the speed signal waveform during rapid feed (G0) operation with shape correction off and during rapid feed operation in manual operation mode. Time constant for post-interpolation rapid feed acceleration/deceleration filter The filter will be invalid if 0 is set.
Return to Library 2 PARAMETER MACHINE Classification Address TIME CONST. Display title Meaning Description The feed rate at which each axis is moved back to the zero-point (reference point) after the zero-point watchdog LS (limit switch) has turned on in the initial operation after power-on.
Return to Library PARAMETER MACHINE Classification Address Display title Meaning 2 TIME CONST. Description The backlash amount to be corrected after the axis movement direction has been reversed in either the rapid-feed (G00) mode or manual mode (except handle-pulse feed mode) Rapid-feed backlash N12 Program type M, E Conditions Immediate Unit 0.00005 mm/0.
Return to Library 2 PARAMETER MACHINE Classification Address TIME CONST. Display title Meaning Description N15 Width to which the machine posture change correction is to be applied N16 Machine posture change correction value N13 Cutting-feed backlash amount N15 Program type Distance after reversing the axis movement direction M, E Conditions At power on Unit 0.00005 mm/0.
Return to Library PARAMETER MACHINE Classification Address Display title Meaning TIME CONST. Description Set the system number of the axes.
Return to Library 2 PARAMETER MACHINE Classification Address TIME CONST. Display title Meaning Description Invalid — N22 to N24 Program type — Conditions — Unit — Setting range — Set the maximum allowable value, Amax, for the acceleration occurring between blocks.
Return to Library PARAMETER MACHINE Classification Address 2 TIME CONST. Display title Meaning Description Set the cutting feed (linear acceleration/deceleration) time constant for superposition control. Note: Set the same value for all axes.
Return to Library 2 PARAMETER 2-3-14 Machine parameter ANOTHER (S) MACHINE Classification Address Display title Meaning ANOTHER Description Invalid — S1 S2 Program type — Conditions — Unit — Setting range — Set for each axis the feed forward gain for acceleration/deceleration before interpolation for the MAZAK Precision Rapid Boring Tornado Option. Feed forward gain for the MAZAK Precision Rapid Boring Tornado Option S3 Program type M, E Conditions Immediate Unit 0.
Return to Library PARAMETER MACHINE Classification Address 2 ANOTHER Display title Meaning Description Set the position of the rotational center of the table in the machine coordinates system. –X S5 S5 –Y Rotational center of the table Notes: 1. Z-axis data are not required for a machine with a tilting table. S5 2. This parameter is used to execute the automatic program origin calculation function (option) for a machine with a tilting table.
Return to Library 2 PARAMETER MACHINE Classification Address ANOTHER Display title Meaning Description Specify the pre-interpolation acceleration/deceleration feed-forward gain levels for each axis. Feed-forward gain G00 S8 Program type M, E Conditions Immediate Unit % Setting range 0 to 100 Invalid — S9 Program type — Conditions — Unit — Setting range — Specify the axis of rotation of the tilting table in machine coordinates (Y and Z).
Return to Library PARAMETER MACHINE Classification Address 2 ANOTHER Display title Meaning Description Axis of rotation of the tilting table (Used for the automatic program origin calculation function) Specify the axis of rotation of the tilting table in machine coordinates (Y and Z). Use this parameter to execute the automatic program origin calculation function (option). Measure and enter data for respective machines. Note: X-axial data are not required.
Return to Library 2 PARAMETER MACHINE Classification Address ANOTHER Display title Meaning Description Set automatically after estimation of the characteristics. Unbalanced axis torque offset S16 Program type M Conditions At power on Unit — Setting range — Specify torque limit buffer reduction ratio 1. Torque limit buffer reduction ratio 1 S17 Program type M, E Conditions Immediate Unit % Setting range 0 to 200 Specify torque limit buffer reduction ratio 2.
Return to Library PARAMETER MACHINE Classification Address Display title Meaning 2 ANOTHER Description Invalid — S20 S21 Program type — Conditions — Unit — Setting range — Specify the critical cutting feed rate to be used during tool tip point control. During tool tip point control, speed is clamped in accordance with parameter S22 or M3 (critical cutting feed rate), whichever is the smaller.
Return to Library 2 PARAMETER 2-3-15 Machine parameter Classification SPINDLE (SA) MACHINE Address SPINDLE Display title Meaning Description Number of revolutions per minute of the spindle in each speed range Address Maximum number of speed ranges 1 2 3 SA1 " L L 4 L SA2 Invalid H M ML SA3 Invalid Invalid H MH SA4 Invalid Invalid Invalid H Example: SA1 to SA8 Maximum RPM of spindle in each speed range (range 1 to 8) Output voltage MAX H L min–1 (rpm) (Spindle speed) S
Return to Library PARAMETER Classification MACHINE Address SPINDLE Display title Meaning Description The maximum number of revolutions per minute of the spindle in each speed range during a tapping cycle SA17 to SA24 Maximum RPM of spindle during tapping cycle (range 1 to 8) Program type M, E Conditions At power on Unit 1 min–1 (rpm) Setting range 0 to 99999 Address Maximum number of speed ranges 1 2 3 SA17 " L L 4 L SA18 Invalid H M ML SA19 Invalid Invalid H MH SA20 I
Return to Library 2 PARAMETER Classification MACHINE Address SPINDLE Display title Meaning Description Specify the minimum spindle speed. Minimum spindle speed SA42 Program type M, E Conditions At power on Unit 1 min–1 (rpm) Setting range 0 to 32767 Specify the channel number for the spindle amplifier.
Return to Library PARAMETER Classification MACHINE Address 2 SPINDLE Display title Meaning Description 76543210 Spindle speed range changing method, in relation to switching the torque factors for auto-pecking of the cutting load detection type (Note 1) 0: As specified by bit 1 1: L/H coil sw. + Mecha.
Return to Library 2 PARAMETER Classification MACHINE Address SPINDLE Display title Meaning Description 76543210 Direction of orientation 00: Shorter route 01: Forward rotation 10: Reverse rotation C-axis position control changeover type 00: After return to zero point 01: After deceleration stop Synchronous tapping position control changeover type 0: After return to zero point 1: After deceleration stop — SA46 Z-phase detection direction 0: Forward rotation 1: Reverse rotation C-axis homing dire
Return to Library PARAMETER Classification MACHINE Address Display title Meaning 2 SPINDLE Description Set the speed attainment detection width. If a value other than 1-99 (%) is set, the value will be regarded as 15 (%). Speed attainment detection width SA49 Program type M, E Conditions Immediate Unit % Setting range 1 to 99 Specify the type of spindle corresponding to the displayed SA parameters, by the appropriate numeric value.
Return to Library 2 PARAMETER Classification MACHINE Address Display title Meaning SPINDLE Description Set the 1/4h (1/2h) rated torque for the L coils of the spindle motor. Spindle 1/4h (1/2h) rated torque for autopecking of the cutting load detection type — L coils SA53 Notes: 1. Only the 1/2h rated torque, not the 1/4h rated torque, may be known for the particular motor. If that is the case, set the 1/2h rated torque.
Return to Library PARAMETER Classification MACHINE Address SPINDLE Display title Meaning Description If the “fms” value depends on spindle speeds, specify the gradient.
Return to Library 2 PARAMETER Classification MACHINE Address SPINDLE Display title Meaning Description Set the value where the width of the flat section in the current feedback data matches estimated data. Spindle coulombic friction coefficient “fms” for auto-pecking of the cutting load detection type — Range 1 Example: If “fms” is 90000 for an “S” value of 5000 and 140000 for S10000, set “c” in L105.
Return to Library PARAMETER Classification MACHINE Address 2 SPINDLE Display title Meaning Description Set the filter for the data which has been sampled at 3.5-msec intervals. If the entered value is “0”, the data actually used will be 4 × 3.5 (msec). Cutting force calculation filter for autopecking of the cutting load detection type SA65 Program type M Conditions Immediate Unit 3.
Return to Library 2 PARAMETER Classification MACHINE Address SPINDLE Display title Meaning Description Set the spindle limit speed at which the time constant for the spindle position control is to be changed Spindle limit speed selection for spindle position control time constants SA81 to SA83 [Spindle speed] SA81: Limit speed 1 SA82: Limit speed 2 SA83: Limit speed 3 Program type Max.
Return to Library PARAMETER Classification MACHINE Address Display title Meaning 2 SPINDLE Description Set the maximum revolutions for conducting Z-phase detection. Z-phase detection speed SA92 Program type M, E Conditions Immediate Unit 1 min–1 (rpm) Setting range 0 to 99999 Set the amount of shifting from the Z-phase when the axis is to be returned to its zero point for synchronous tapping.
Return to Library 2 PARAMETER Classification MACHINE Address Display title Meaning SPINDLE Description Set the amount of shifting from the zero point of orientation control. Amount of orientation position shifting SA96 Program type M, E Conditions Immediate Unit 0.
Return to Library PARAMETER Classification MACHINE Address Display title Meaning 2 SPINDLE Description Invalid — SA100 to SA113 Program type — Conditions — Unit — Setting range — Set the spindle speed to be monitored in safety supervisory mode 2. Spindle speed supervisory mode 2 for safety supervision If the operating speed of the spindle exceeds the set value in safety supervisory mode 2, this will cause a safety supervisory alarm and bring the machine to an emergency stop.
Return to Library 2 PARAMETER Classification MACHINE Address Display title Meaning SPINDLE Description Set the spindle safety clamping speed to be monitored in safety supervisory mode 3. Spindle safety clamping mode 3 for safety supervision SA117 In safety supervisory mode 3 and while a safety clamping request is in effect, the spindle is decelerated to the set speed. Assign a value smaller than the speed value to be monitored in mode 3 (i.e., specified in SA115).
Return to Library PARAMETER Classification MACHINE Address Description Amount of branching point correction for spindle index gear tooth SA121 to SA128 SPINDLE Display title Meaning Set the amount of correction at the branching point where one PLG gear tooth is split into eight equal segments.
Return to Library 2 PARAMETER Classification MACHINE Address Display title Meaning SPINDLE Description Invalid — SA141 to SA143 Program type — Conditions — Unit — Setting range — 76543210 Spindle gear changeover valid Turret indexing valid.
Return to Library PARAMETER 2-3-16 Machine parameter Classification BARRIER (BA) MACHINE Address 2 BARRIER Display title Meaning Description Setting of chuck outside diameter of the No. 1 turning spindle Chuck outside diameter (for chuck barrier) — No. 1 turning spindle BA1 BA1 NM211-00312 Program type M, E Conditions Immediate Unit 0.001 mm/0.0001 inch Setting range 0 to 99999999 Setting of chuck width of the No. 1 turning spindle BA2 Chuck width (for chuck barrier) — No.
Return to Library 2 PARAMETER Classification MACHINE Address BARRIER Display title Meaning Description Specify the workpiece outside diameter to be used for the EIA program. EIA program workpiece outside diameter BA4 BA4 Program type E Conditions Immediate Unit 0.001 mm/0.0001 inch Setting range 0 to 99999999 BA17 Setting of chuck outside diameter of the No. 2 turning spindle Chuck outside diameter (for chuck barrier) — No.
Return to Library PARAMETER Classification MACHINE Address Display title Meaning 2 BARRIER Description Setting of tail body outside diameter Tail body outside diameter (for tail barrier) BA8 BA8 Program type NM211-00315 M, E Conditions Immediate Unit 0.001 mm/0.0001 inch Setting range 0 to 99999999 Setting of tail body length BA9 Tail body length (for tail barrier) BA9 Program type M, E Conditions Immediate Unit 0.001 mm/0.
Return to Library 2 PARAMETER Classification MACHINE Address BARRIER Display title Meaning Description Setting of tail head outside diameter Tail head outside diameter (for tail barrier) BA12 BA12 Program type NM211-00319 M, E Conditions Immediate Unit 0.001 mm/0.0001 inch Setting range 0 to 99999999 Setting of tail head length BA13 Tail head length (for tail barrier) BA13 Program type M, E Conditions Immediate Unit 0.001 mm/0.
Return to Library PARAMETER Classification MACHINE Address 2 BARRIER Display title Meaning Description Set the dimensional data for forming tail barriers using an EIA/ISO program.
Return to Library 2 PARAMETER Classification MACHINE Address BARRIER Display title Meaning Description Specify the jaw number that has been registered on the CHUCK JAW DATA display to be referred to in the EIA program when forming a jaw barrier for the No. 1 turning spindle. Jaw number for EIA program barrier — No.
Return to Library PARAMETER MACHINE Classification Address 2 BARRIER Display title Meaning Description Setting of tool holder mounting position. When plus data is used, the tool holder is mounted horizontally, and minus data downward. Tool holder mounting position BA27 BA30 BA33 BA36 Example: Type 1 Turret reference positon BA27 - Type 1 BA30 - Type 2 BA33 - Type 3 BA36 - Type 4 Program type BA27 (> 0) M Conditions Immediate Unit 0.001 mm/0.
Return to Library 2 PARAMETER Classification MACHINE Address BARRIER Display title Meaning Description Set the holder shape data for forming tool barriers using an EIA/ISO program. Input BA39 with a minus sign. BA40 BA39 BA41 Input BA39 with a plus sign. Input BA41 with a plus sign. EIA tool barrier BA39 to BA41 Holder dimensions Input BA39 with a plus sign. Input BA41 with a minus sign.
Return to Library PARAMETER Classification MACHINE Address Display title Meaning BARRIER Description Set the first tool number assigned to the first set of tools. First tool number (in the 1st set of tools) BA43 Program type M, E Conditions At power on Unit — Setting range 1 to 4000 Set the number of tools assigned as the first set of tools.
Return to Library 2 PARAMETER Classification MACHINE Address BARRIER Display title Meaning Description Set the type of turret: 0: 1: 2: 3: 4: Turret type BA47 Program type M, E Conditions At power on Unit — Setting range 0 to 4 ATC Turret Lower turret Opposed turret Work rest Set the axis name of the head axis to be rotated. Set “&42” if the head axis to be rotated is the B-axis.
Return to Library PARAMETER Classification MACHINE Address 2 BARRIER Display title Meaning Description Specify one of the vectors created by the triangles formed by inclination angles.
Return to Library 2 PARAMETER Classification MACHINE Address BARRIER Display title Meaning Description Set the turning spindle to be used in the D1 command mode of polygonal machining. Turning spindle number for polygonal machining (D1) BA55 Program type E Conditions Immediate Unit — Setting range –1 to 3 0: 1: 2: 3: –1: Turning spindle No. 1 Turning spindle No. 2 Turning spindle No. 3 Turning spindle No.
Return to Library PARAMETER Classification MACHINE Address 2 BARRIER Display title Meaning Description Spindle forward rotation M-code for tapping cycle - If the command block of G284/G288 (machining G-codes, F30 = 0) or of G84/G88 (turning G-codes, F30 = 1) does not contain spindle forward/reverse rotation M-codes, one of the following M-codes will be output, depending on the status of bit 0 in parameter SU153: BA59 SU153 Bit 0 Program type M, E Conditions Immediate Unit — Setting range
Return to Library 2 PARAMETER Classification MACHINE Address BARRIER Display title Meaning Description Set the holder angle of the angle tool holder. According to the value set in this parameter, the holder angle is set in HLD.TYPE on the TOOL DATA display. Holder angle of angle tool holder BA63 = 45 BA63 Program type M Conditions Unit 1° Setting range 0 to 90 HLD.TYP: 45 (180 – BA63 = 135) HLD.
Return to Library PARAMETER Classification MACHINE Address 2 BARRIER Display title Meaning Description Set the deceleration area and measuring area in the G36 command. BA68 BA69 BA68: Set the distance between the starting point of movement at the measuring rate, and the measuring point. This value will be used when argument R is omitted from the G36 command. G36 deceleration area G36 measuring area BA69: Set the moving distance in measuring feed mode.
Return to Library 2 PARAMETER Classification MACHINE Address Display title Meaning BARRIER Description Invalid — BA72 Program type — Conditions — Unit — Setting range — 0: Chuck, sub-chuck and tailstock invalid 1: Chuck valid 2: Sub-chuck valid Barrier valid/invalid 1 (chuck, sub-chuck, tailstock) 3: Tailstock valid BA73 Program type M, E Conditions Immediate Unit — Setting range 0 to 3 0: Lower turret and work rest invalid 1: Lower turret valid 2: Work rest valid Barrier vali
Return to Library PARAMETER Classification MACHINE Address 2 BARRIER Display title Meaning Description Set the reference position when it is viewed from the machine zero point.
Return to Library 2 PARAMETER Classification MACHINE Address BARRIER Display title Meaning Description Set the reference position within a tail barrier area. The reference position here refers to the position when viewed from the machine zero point of the upper turret of the tailstock being not used for machining.
Return to Library PARAMETER MACHINE Classification Address 2 BARRIER Display title Meaning Description When using the C-axes of the HD1/HD2 in the lower turret system, set the offset angle with respect to the upper turret, for the lower turret system. BA93: Upper/lower turret tool angle difference (HD1) BA93 BA94 BA94: Upper/lower turret tool angle difference (HD2) BA93 BA93 XX Y Y Program type CC C C BA94 BA94 XX Y Y M, E Conditions Immediate Unit 0.
Return to Library 2 PARAMETER Classification MACHINE Address BARRIER Display title Meaning Description Setting of sensor reference point Y coordinate BA98: BA98 BA101 Y-coordinate of the sensor’s reference point BA101: Y-coordinate of the sensor’s reference point (for lower turret/HD2) Program type M Conditions Immediate Unit 0.0001 mm/0.00001 inch Setting range ±99999999 B98 Machine zero point Set adjustment “FdT” for holding the thrust of the W-axis.
Return to Library PARAMETER Classification MACHINE Address 2 BARRIER Display title Meaning Description Set the drooping level for holding the W-axis thrust. This drooping level is held during the application of the W-axis thrust. W-axis thrust hold droop BA108 Program type M, E Conditions After stop of movement Unit 0.0005 mm/0.
Return to Library 2 PARAMETER Classification MACHINE Address Display title Meaning BARRIER Description Invalid — BA117 to BA124 Program type — Conditions — Unit — Setting range — Set the types of tailstock, tool holder and chuck for which the EIA barriers are to be activated.
Return to Library PARAMETER Classification MACHINE Address Display title Meaning 2 BARRIER Description 76543210 System to be made valid without system selection for queuing Y-axis interference type 0 : Type A 1 : Type B Y-axis moving range display 0 : Invalid 1 : Valid Tool command scheme (Note) 0 : M06 required. 1 : M06 not required.
Return to Library 2 PARAMETER 2-3-17 Data I/O parameter CMT parameter (CMT) Parameter setting D740H0001E Classification DATA I/O CMT Display title Meaning Description Baud rate for RS-232C interface Set values BAUDRATE Program type M, E Conditions At I/O startup Unit — Setting range 110 to 19200 110 4800 300 9600 1200 19200 2400 Type of processing to be executed if the machining program of an existing work number is to be loaded SAME WNo.
Return to Library PARAMETER Classification DATA I/O CMT Display title Meaning Description CMT port selection PORT Program type M, E Conditions At I/O startup Unit — Setting range — 2-343 Set values Description COM1 CF22 serial ch1 COM2 CF22 serial ch2 COM3 Invalid COM4 Invalid 2
Return to Library 2 PARAMETER DATA I/O Classification Address Display title Meaning Description Invalid — CMT1 to CMT32 CMT Program type — Conditions — Unit — Setting range — 2-344
Return to Library PARAMETER 2-3-18 Data I/O parameter 2 TAPE parameter (TAP) Parameter setting D740H0002E Classification DATA I/O TAPE Display title Meaning Description Baud rate for RS-232C interface Set values BAUDRATE Program type M, E Conditions At I/O startup Unit — Setting range 110 to 19200 110 4800 300 9600 1200 19200 2400 Number of data bits (parameter for RS-232C interface initialization) Set values DATA BITS 7 8 Program type M, E Conditions At I/O startup Unit —
Return to Library 2 PARAMETER Classification DATA I/O TAPE Display title Meaning Description Parity check (parameter for RS-232C interface initialization) Set values PARITY NONE ODD EVEN Program type M, E Conditions At I/O startup Unit — Setting range — Number of stop bits (parameter for RS-232C interface initialization) Set values STOP BITS 1 1.
Return to Library PARAMETER Classification DATA I/O 2 TAPE Display title Meaning Description Selection of paper tape puncher output code Set values ISO FORMAT EIA ASCII Program type M, E Conditions At I/O startup Unit — Setting range — Description Paper tape punching in ISO code Paper tape punching in EIA code Paper tape punching in ASCII code Type of processing to be executed if the machining program of an existing work number is to be loaded Set values SAME WNo.
Return to Library 2 PARAMETER DATA I/O Classification Address TAPE Display title Meaning Description Set values Type of terminator TAP1 Program type M, E Conditions At I/O startup Unit — Setting range 0 to 5 Terminator 0 Without terminator 1 EOB or EOR 2 EOB only 3 EOR only 4 One character of your choice 5 Two characters of your choice Effective only when TAP1 is set to 4 or 5.
Return to Library PARAMETER DATA I/O Classification Address 2 TAPE Display title Meaning Description This parameter is used to specify whether or not a parity bit is to be assigned to the DC code to be output. Set values Parity 0 No assignment 1 Assignment DC code parity TAP5 Program type M, E Conditions At I/O startup Unit — Setting range 0, 1 Hole-punching pattern of DC3 code ! ! ! • • ! ! ! ! Note: This parameter is valid only when HAND SHAKE is set to DC CONTROL.
Return to Library 2 PARAMETER DATA I/O Classification Address Display title Meaning TAPE Description This parameter is used to set a hole-punching pattern for the character code “[” onto a paper tape reader/puncher using EIA. Set an eight-digit binary number in decimal form.
Return to Library PARAMETER DATA I/O Classification Address Display title Meaning 2 TAPE Description This parameter is used to set a hole-punching pattern for the character code “=” onto a paper tape reader/puncher using EIA. Set an eight-digit binary number in decimal form.
Return to Library 2 PARAMETER DATA I/O Classification Address Display title Meaning TAPE Description Invalid — TAP17 to TAP24 Program type — Conditions — Unit — Setting range — 76543210 Paper tape puncher parity-V check TAP25 0: No parity-V check during paper tape reading 1: Parity-V check during paper tape reading Program type M, E Conditions At I/O startup Unit Bit Setting range Binary, eight digits 76543210 Data transfer of a paper tape program which has been punched by M2
Return to Library PARAMETER DATA I/O Classification Address 2 TAPE Display title Meaning Description 76543210 To specify whether or not M99 is to be set as the program end code in reading of paper tape 0: Set as program end 1: Not set as program end To specify whether or not M02 is to be set as the program end code in reading of paper tape 0: Set as program end 1: Not set as program end To specify whether or not M30 is to be set as the program end code in reading of paper tape 0: Set as program en
Return to Library 2 PARAMETER DATA I/O Classification Address TAPE Display title Meaning Description The total number of space-characters that are punched out between Onumber and program section.
Return to Library PARAMETER 2-3-19 Data I/O parameter 2 DNC parameter (DNC) Parameter setting D740H0003E Classification DATA I/O DNC Display title Meaning Description Baud rate for RS-232C interface Set values BAUDRATE 110 300 9600 1200 19200 2400 Program type M, E Conditions At I/O startup Unit — Setting range 110 to 19200 2-355 4800
Return to Library 2 PARAMETER Classification DATA I/O DNC Display title Meaning Description Number of data bits (parameter for RS-232C interface initialization) Set values DATA BITS 7 8 Program type E Conditions At I/O startup Unit — Setting range 7, 8 Parity check (parameter for RS-232C interface initialization) Set values PARITY NONE ODD EVEN Program type E Conditions At I/O startup Unit — Setting range — Number of stop bits (parameter for RS-232C interface initialization) Set v
Return to Library PARAMETER Classification DATA I/O 2 DNC Display title Meaning Description Type of processing to be executed if the machining program of an existing work number is to be loaded Set values SAME WNo. Program type E Conditions At I/O startup Unit — Setting range — Description ALARM Issues an alarm if the received work number already exists. LOAD Overrides the program if the received work number already exists.
Return to Library 2 PARAMETER DATA I/O Classification Address DNC Display title Meaning Description Set values Type of terminator DNC1 Program type E Conditions At I/O startup Unit — Setting range 0 to 5 Terminator 0 Without terminator 1 EOB or EOR 2 EOB only 3 EOR only 4 One character of your choice 5 Two characters of your choice Effective only when DNC1 is set to 4 or 5.
Return to Library PARAMETER DATA I/O Classification Address 2 DNC Display title Meaning Description This parameter is used to specify whether or not a parity bit is to be assigned to the DC code to be output.
Return to Library 2 PARAMETER DATA I/O Classification Address DNC Display title Meaning Description This parameter is used to set the number of times that transmission/reception of command messages is to be repeated in the case that it is not correctly performed.
Return to Library PARAMETER DATA I/O Classification Address 2 DNC Display title Meaning Description The NC stop time from reception of ! from the host system to transmission of ∗. HOST NC ∗ NC stop time after reception of ! ! DNC15 DNC15 ∗ MPL086 Program type M, E Conditions At I/O startup Unit 0.1 sec. Setting range 0 to 255 Code ∗ is transmitted to the host system if the time that has been set with DNC15 elapses following reception of !.
Return to Library 2 PARAMETER DATA I/O Classification Address DNC Display title Meaning Description The NC waiting time from transmission of command message EOT to reception of command reply message ∗ from the host system. HOST NC ∗ @ DNC command reply message waiting time TEXT DNC18 Command messages @ EOT Program type M, E Conditions At I/O startup Unit 0.1 sec.
Return to Library PARAMETER DATA I/O Classification Address Display title Meaning 2 DNC Description Invalid — DNC22 to DNC24 Program type — Conditions — Unit — Setting range — 76543210 — DNC25 Program type M, E Conditions At I/O startup Unit Bit Setting range Binary, eight digits Select the type of processing to be executed if the tool quantity data within the NC memory mismatches that which has been transferred from the DNC memory.
Return to Library 2 PARAMETER DATA I/O Classification Address Display title Meaning DNC Description Invalid — DNC27 DNC28 Program type — Conditions — Unit — Setting range — Number of retry times with detection of a physical error DNC29 Program type M, E Conditions At I/O startup Unit Number of times Setting range 0 to 65535 Select a tool data/tool file message format.
Return to Library PARAMETER 2-3-20 Data I/O parameter 2 OTHER (IOP/DPR/IDD) D740H0004E DATA I/O Classification Address Display title Meaning OTHER Description Invalid — IOP1 to IOP4 Program type — Conditions — Unit — Setting range — 76543210 Valid for loading a program(s) of the same work number as that of the program(s) registered in the NC unit by hard disk, floppy disk, or memory card input/output.
Return to Library 2 PARAMETER DATA I/O Classification Address OTHER Display title Meaning Description Invalid — IOP6 Program type — Conditions — Unit — Setting range — 76543210 Specify the serial port number of the NC unit that is to be used for communication with the magazine-side display unit. Bit 1 0 0 1 1 Data entry for communication with the magazine-side display unit Bit 0 0 1 0 1 Serial port COM1 COM2 COM3 COM4 Fixed (0) Specify the type of ID amplifier.
Return to Library PARAMETER DATA I/O Classification Address 2 OTHER Display title Meaning Description Specify the number of pitch error axes during machine parameter output using the text input/output functions. Number of pitch error axes during text output Note: If 0 is entered, machine parameter output will be valid for all axes (14 axes).
Return to Library 2 PARAMETER DATA I/O Classification Address OTHER Display title Meaning Description Invalid — DPR3 Program type — Conditions — Unit — Setting range — Number of data bits (parameter for RS-232C interface initialization) Set values Data bit Set values Data bit 0 8 1 7 DPR4 Program type M, E Conditions At I/O startup Unit — Setting range 0, 1 Invalid — DPR5 to DPR7 Program type — Conditions — Unit — Setting range — This parameter specifies whether “
Return to Library PARAMETER DATA I/O Classification Address 2 OTHER Display title Meaning Description This parameter is used to select the method of handshaking to control the state of data transfer between the NC system and connected device.
Return to Library 2 PARAMETER DATA I/O Classification Address OTHER Display title Meaning Description The waiting time for replies from the connected device during inputting or outputting. An alarm occurs if this time elapses following the final reply. Waiting time DPR12 Program type M, E Conditions At I/O startup Unit 0.1 sec.
Return to Library PARAMETER DATA I/O Classification Address Display title Meaning OTHER Description Invalid — DPR16 Program type — Conditions — Unit — Setting range — Invalid — IDD1 to IDD16 Program type — Conditions — Unit — Setting range — 2-371 2
Return to Library 2 PARAMETER - NOTE - 2-372 E
Return to Library ALARM 3 3 ALARM If machine failures occur or if erroneous operations are carried out, appropriate alarm numbers and messages will be displayed in the alarm display section of the screen. If alarm display appears, refer to the alarm list to locate and eliminate the cause of the alarm. More than one alarm may be raised at once, depending on the particular status of alarm occurring.
Return to Library 3 ALARM 3-1 Outline 1. Scope of this chapter This chapter describes all the alarms displayed on the screen of NC unit. Always refer to this chapter for eliminating an alarm. 2. Precautions on this chapter This chapter also lists alarms related to machine model-dependent functions and optional functions. These alarms may therefore include ones not displayed for your machine. Check the type of machine purchased by you and its specifications before you read this chapter.
Return to Library ALARM 3-1-2 3 Precautions 1. If program-related alarm display appears, that portion of the program in which the alarm has occurred will be displayed within the parentheses next to the alarm message. The meaning of each code in parentheses on the alarm list is listed in the table below. Code Meaning WNo. Work number (MAZATROL or EIA/ISO) UNo. Unit number (MAZATROL) SNo. Tool sequence number (MAZATROL) NNo. Sequence number (EIA/ISO) BNo.
Return to Library 3 ALARM 3-2 Detailed Description 3-2-1 Structure of the alarm list This alarm list is written in the following format: No. Message [1] [2] ( , , [6] Action [7] A [3] [4] [5] Type Display Description Operation A wrong key has been pressed. Or the machine has been operated incorrectly. B Registered data The program or tool data includes an error(s).
Return to Library ALARM 3-2-2 No. 1 - No. 99, No. 1000 - No. 1099 (System/Drive error) No. 1 Message EMERGENCY STOP Cause —— Action —— 2 Cause Action 3 Cause Action EMERGENCY STOP EMERGENCY STOP —— —— Cause Action 7 Cause Action 8 Cause Action 9 Cause Action ) ( , , ) Display E H M Red ( , , ) A H M Red H M Red Release the pressed state of the emergency stop button and reset the NC unit to its initial state.
Return to Library 3 ALARM No. 10 Cause Action 11 Cause Action 12 Cause Action 13 Cause Action Message DETECTOR MALFUNCTION (Alarm No., Axis, Type of error Stopped status Clearing procedure Display E H M Red M Red ) The absolute position detection system has detected its detector error(s). Require Mazak Technical Center or Technology Center to replace the encoder or bettery. POSITION REFERENCE MALFUNCTION (Alarm No.
Return to Library ALARM No. 25 Message SAFE OPERATION SYSTEM ALARM (Alarm No., Axis/Door, Type of error Stopped status Clearing procedure Display E H N Red ) There occurred an alarm in the safe operation system. Alarm No. 1 Cause Discrepancy between parameters. The parameters stored in the NC memory for the safe operation system differ from those which are sent to the drive units. 2 Abnormal speed command.
Return to Library 3 ALARM No. 32 Cause Action 33 Cause Action 34 Cause Action 35 Cause Action Message SERVO PARAMETER MALFUNCTION (Alarm No., Axis, ) Type of error Stopped status Clearing procedure Display C H M Red The parameters that have been transferred from the NC unit to the servo amplifier during NC power-on are not correct. Require Mazak Technical Center or Technology Center to re-set the servo parameters. SERVO MALFUNCTION 2 (Alarm No.
Return to Library ALARM No. Message ( , , ) ( , , ) 3 Type of error Stopped status Clearing procedure Display E L D Blue D Blue Cause Action 51 Cause Action 52 E2ROM MALFUNCTION Trouble has occurred during communication with MR-JT-C2. Parameters cannot be correctly written into the E2ROM. Require Mazak Technical Center or Technology Center to replace the MR-JT-C2 amplifier.
Return to Library 3 ALARM No. 57 Cause Action 58 Cause Action 59 Cause Action Type of error Stopped status Clearing procedure Display ) F H N Red (Step No., Status, Program No.) F H N Red/Blue Message NO PLC ( , , The user PLC is not stored in the NC unit. Contact Mazak Technical Center or Technology Center. CORRUPT PLC Trouble has occurred with the PLC. Contact Mazak Technical Center or Technology Center with the information of the second item (Status) displayed in parentheses.
Return to Library ALARM No. 71 Cause Action 72 Cause Action Message ILLEGAL SERVO PARAMETER (Alarm No., Axis, ) Type of error Stopped status Clearing procedure Display C H M Blue The parameters that have been transferred from the NC system to the servo amplifier during NC power-on are not correct. Contact Mazak Technical Center or Technology Center. SERVO WARNING (Alarm No., Axis, ) E H O Blue The servomotor is loaded abnormally.
Return to Library 3 ALARM 3-2-3 No. 100 - No. 199, No. 1100 - No. 1199 (CNC machine control error) No. Message 100 —— Cause —— Action —— 101 Cause Action SOFT LIMIT ( , , ) (Axis, , ) Type of error Stopped status Clearing procedure Display A K P Blue Some mistake in operations during the automatic operation has caused the tool tip to overstep the area specified in the software limit parameters in the direction of the axis corresponding to the displayed axis name.
Return to Library ALARM No. 129 Cause Action 130 Cause Action 131 Cause Action 132 Message INSIDE INTERLOCK AXIS ( , , 3 Type of error Stopped status Clearing procedure Display A K P Red ) The very direction in which the manual skip function has become effective is specified in the axis-movement command. Or the servo-off function is active. Deactivate the servo-off function.
Return to Library 3 ALARM No. 138 Cause Action 139 Cause Action 140 Cause Action 141 Cause Action Message CANNOT ROTATE TABLE ( , , Type of error Stopped status Clearing procedure Display A K P Red A K M Red A K P Blue ) There are areas where the machining with table rotation cannot be executed. Modify the approach point. PRE-INTERP ACCEL/DECEL ERROR ( , , ) Trouble has occurred during pre-interpolation acceleration/deceleration.
Return to Library ALARM No. 144 Message ILLEGAL CYCLE START (Alarm No., , 3 Type of error Stopped status Clearing procedure Display A I O Red ) It was attempted to start automatic operation under the following conditions: Alarm No. 0 × 101 Cause Cause During axis movement 0 × 102 READY lamp OFF. 0 × 103 Reset state not yet cleared. 0 × 104 – 0 × 105 Hardware overtravel not yet cleared. 0 × 106 Software overtravel not yet cleared.
Return to Library 3 ALARM No. 149 Cause Action 150 Cause Action 151 Cause Action 152 Message TAILSTOCK BARRIER ( , , ) Type of error Stopped status Clearing procedure Display A K O Red The tool entered in the tail barrier. Correct the machining program. If the program is correct, review the tool data and the parameters related to the barrier. WORK PIECE BARRIER ( , , ) A, B H O Red Interference is occurring between the workpiece of the No.
Return to Library ALARM No. 158 Cause Action 159 Message ILLEGAL COMMAND CROSS MACHINING ( , , Stopped status Clearing procedure Display A K Q Blue P Red ) The axes under the cross machining control cannot be controlled manually. (Alarm No , , ) Alarm No. Cause Type of error It was attempted to manually control an axis currently under the control for cross machining. CROSS MACHINING IMPOSSIBLE E I Cause 0 × 0001 The specified axis does not exist in the counterpart system.
Return to Library 3 ALARM No. 165 Cause Action 166 Cause Action 167 Cause Action 168 Cause Action 169 Cause Action 170 Cause Action 171 Cause Action 172 Cause Action 173 Cause Action Message CANNOT MAKE SAFE OPER SYS ACTIVE ( , , Type of error Stopped status Clearing procedure Display A L Q Blue ) The command signal for the control for safety speed was turned on in the following modes of machining: Threading, Synchronous tapping, Cross machining, Superposition control.
Return to Library ALARM No. 174 Cause Action 175 Cause Action 176 Cause Action 177 Message 2ND SPDL 1/1000 N/A ( , , 3 Type of error Stopped status Clearing procedure Display B I N Red I N Red I P Red ) The No. 2 spindle/C-axis is used without the No. 2 spindle high-precision indexing option. Purchase the No. 2 spindle high-precision indexing option. TABLE UNBALANCE CHECK N/A ( , , ) B Vibration detection is used without the rotary table vibration detection option.
Return to Library 3 ALARM No. 192 Cause Action 193 Cause Action 194 Cause Action 195 Cause Action 196 Cause Action 197 Cause Action 198 Cause Action 199 Cause Action Message EXECUTION IMPOSSIBLE (WNo., UNo., SNo.) Type of error Stopped status Clearing procedure Display E I P Red An internal error(s) has occurred during execution of the MMS unit. After checking the entire data of the program being executed, tool data, tool file, parameters, etc.
Return to Library ALARM No. 1101 Cause Action 1102 Cause Action 1103 Cause Action Message INTERFERE ( , , ) Type of error Stopped status Clearing procedure Display A K S Blue I P Red L S Blue Interference occurs between and . Press the cancel key to clean the alarm. INTERFERE ( , , ) A Interference occurs between and . Press the reset key to clean the alarm.
Return to Library 3 ALARM 3-2-4 No. 200 - No. 399, No. 1200 - No. 1399 (PLC machine control error) For alarms related to PLC machine control (No. 200 to No. 399 and No. 1200 to No. 1399) refer to the Operating Manual of the machine.
Return to Library ALARM 3-2-5 No. 400 - No. 499, No. 1400 - No. 1499 (CNC screen operation error) No. Message 400 —— Cause —— Action —— 401 Cause 3 ILLEGAL FORMAT ( , , ) ( , , ) Type of error Stopped status Clearing procedure Display A L S Blue L S Blue The format of the input data is not an available one. Example: Negative data has been input to an item that rejects negative data input. Action 402 Cause Press the data cancellation key and then input correct data.
Return to Library 3 ALARM No. 407 Cause Action 408 Cause Action 409 Cause Action 410 Cause Message DESIGNATED DATA NOT FOUND ( , , Type of error Stopped status Clearing procedure Display A L S Blue L S Blue ) The number or character string that has been designated does not exist in the program. Designate an existent number or character string. PROGRAM ERROR ( , , ) A The memory contents in the machining-program data storage area have been destroyed.
Return to Library ALARM No. 415 Cause Action 416 Cause Action 417 Cause Action 418 Message MIS-SET G CODE ( , , ) 3 Type of error Stopped status Clearing procedure Display B L S Blue A L S Blue L S Blue L S Blue A G-code not covered by the specifications has been designated. Check and correct the G-code addresses within the program. AUTO PROCESS IMPOSSIBLE ( , , ) Tools cannot be automatically developed because of errors of the machining-unit data.
Return to Library 3 ALARM No. 423 Cause Action 424 Cause Action 425 Message MAX NUMBER OF TOOLS EXCEEDED ( , , ) Type of error Stopped status Clearing procedure Display A L S Blue During tool layout, the number of tools used in the designated program has exceeded the maximum available number. Check and correct the corresponding machining program so that the maximum available number of tools is not exceeded.
Return to Library ALARM No. 431 Cause Action 432 Cause Action 433 Cause Action 434 Cause Action 435 Cause Action 436 Cause Action 437 Cause Action 438 Cause Action 439 Cause Action Message ILLEGAL PALLET No. ( 3 Type of error Stopped status Clearing procedure Display , , ) A L S Blue , , ) A L S Blue , , ) A L S Blue A nonexistent pallet number has been designated. Designate a correct pallet number. ILLEGAL TOOL No. ( A nonexistent tool number has been designated.
Return to Library 3 ALARM No. 440 Message EIA/ISO PROGRAM DESIGNATED ( , , ) Type of error Stopped status Clearing procedure Display A L S Blue 1. The machining program that has been designated on the TOOL LAYOUT, PROCESS CONTROL or SET UP RECORD display is an EIA/ISO program. Cause 2. An EIA/ISO program has been designated for copying purposes during MAZATROL program editing. 3. An EIA/ISO program has been designated as the source program of EIA/ISO conversion. 4.
Return to Library ALARM No. 448 Cause Action 449 Cause Action 450 Cause Action 451 Cause Action 452 Cause Action 453 Cause Action 454 Type of error Message RESTART SEARCH UNFINISHED ( , , Stopped status Clearing procedure 3 Display ) EIA/ISO restart searching has not been executed. Designate the restart position and press the [EIA/ISO SEARCH] button to search the intended restart position.
Return to Library 3 ALARM No. 457 Cause Action 458 Message DATA ADDRESS NOT FOUND ( , , ) Type of error Stopped status Clearing procedure Display A L S Blue During creation of manual program mode unit, data setting has been attempted without addressing. During creation of the manual program mode unit, designate an address before setting data. INTERFERING TOOL REGISTERED ( , , ) An attempt has been made to register a tool most likely to interfere with an adjacent pocket.
Return to Library ALARM No. 465 Cause Message EIA SHAPE DATA NOT FOUND ( , , 3 Type of error Stopped status Clearing procedure Display A L S Blue ) Although an attempt has been made to draw a workpiece shape using the selected EIA/ISO program, shape data is not present in that program. Review the program.
Return to Library 3 ALARM No. 473 Cause Action 474 Message FINAL POINT DATA NOT FOUND ( , , ) Type of error Stopped status Clearing procedure Display B L S Blue Although the end-point data of the preceding line was not yet set in the BAR or CPY unit, the [NEXT] menu key was pressed. Press the [NEXT] menu key after setting the end-point data of the preceding line. NO PROGRAM DISPLAY (TAPE MODE) ( , , ) A L S Blue 1.
Return to Library ALARM No. Message 482 —— Cause —— Action —— 483 Cause Action 484 Cause Action 485 SOLID DESCRIP. IMPOSSIBLE UNIT ( , , 3 Type of error Stopped status Clearing procedure Display B I S Blue ) (WNo., UNo., ) Checking the program including the units or conditions (such as the case that angle B is set in the index unit of the initialpoint scheme) that do not allow graphics to be drawn in SOLID mode has been attempted in the SOLID mode of the TOOL PATH CHECK display.
Return to Library 3 ALARM No. 491 Cause Action 492 Cause Action 493 Cause Action 494 Cause Action 495 Cause Message ITEM NOT SETUP Type of error Stopped status Clearing procedure Display ( , , ) A L S Blue ( , , ) B L S Blue , , ) A L S Blue S Blue Data registration is not yet complete. Check if all the data items are set as required. CANNOT EDIT 3D DATA Editing the CAD tool model has been attempted. The CAD tool model cannot be edited.
Return to Library ALARM No. 499 Cause Action Message ILLEGAL HEAD TYPE ( , , ) 3 Type of error Stopped status Clearing procedure Display A L S Blue An attempt has been made to perform tool tip position storage on the TOOL DATA or TOOL OFFSET display during use of the horizontal type of head. To perform tool tip position storage for tool length measurement, mount a vertical head or a cover.
Return to Library 3 ALARM No. 1400 Cause Message SYSTEM ERROR ( , , ) Type of error Stopped status Clearing procedure Display A L S Blue An internal trouble has occurred in the system. Action Contact Mazak Technical Center or Technology Center with the information of the particular operation causing the alarm, and of the codes displayed in parentheses. 1401 FILE OPEN ERROR Cause ( , , ) A L S Blue Trouble has occurred in opening a file from the hard disk.
Return to Library ALARM No. 1408 Cause Message DATA TRANSFER ERROR ( , , 3 Type of error Stopped status Clearing procedure Display A L S Blue ) Data transfer to the NC was not successful. Action Contact Mazak Technical Center or Technology Center with the information of the particular operation causing the alarm, and of the codes displayed in parentheses.
Return to Library 3 ALARM No. 1417 Cause Action 1418 Cause Action Message PARAMETER ERROR CANNOT USE LOWER TURRET —— —— 1420 FILE SIZE LIMIT EXCEEDED —— —— Action —— 1422 PROGRAM LAYOUT ERROR Action 1424 Cause Action 1425 Cause Action S Blue ( , , ) S Blue A L ( , , ) ( , , ) A L S Blue A L S Blue L S Blue Delete the file, or rename the file. Cause Cause L The size of the file is too large for new data to be written in it.
Return to Library ALARM No. 1426 Cause Message NO PROG LAYOUT FOR THIS PROCESS ( , , Type of error Stopped status Clearing procedure Display A L S Blue ) The current process has no program layout information provided. Action Press the menu selector key to select a process with program layout data, or select the display mode for all processes.
Return to Library 3 ALARM 3-2-6 No. 500 - No. 599, No. 1500 - No. 1599 (I/O error) No. Message 500 —— Cause —— Action —— 501 Cause Action 502 Cause ILLEGAL FORMAT ( , , ) ( , , ) Type of error Stopped status Clearing procedure Display A L S Blue L S Blue An external storage medium that contains data other than MATRIX data has been set. Check the contents of the external storage medium for appropriateness to the MATRIX. CANNOT LOAD (PROG SIZE EXCEED) (WNo.
Return to Library ALARM No. 508 Cause Message MEMORY CAPACITY EXCEEDED (WNo., , ) 3 Type of error Stopped status Clearing procedure Display A (G) L (L) S (S) Blue (Blue) 1. An attempt has been made to load machining program data that exceeds the maximum available area for program registration within the NC unit. 2. In the middle of saving onto the external storage medium, data saving exceeding the memory capacity has been made, or the end-of-tape (or end-of-disk) code has been detected.
Return to Library 3 ALARM No. 516 Cause Message SYSTEM ERROR ( , , ) Type of error Stopped status Clearing procedure Display E L S Blue 1. When program loading was attempted, there was not a comment file (C:\MC_MachinePrograms\index.tbl). 2. An error has occurred within the system. Action 1. Enter any comment on the PROGRAM FILE display, and load the program. Do not edit or delete “index.tbl” since it is the management file for NC. 2. Contact Mazak Technical Center or Technology Center.
Return to Library ALARM No. 524 —— Cause —— Action —— 525 Cause Action Type of error Message HDD I/O ERROR ( , , (Cause, Stopped status Clearing procedure 3 Display ) , ) An error has occurred during output of data of the measurements results print-out function to the hard disk drive. Check if the available space within the hard disk drive is sufficient for the purpose.
Return to Library 3 ALARM No. 535 Cause Message CMT WRITE PROTECT ( , , Type of error Stopped status Clearing procedure Display A L S Blue L S Blue ) Data saving onto a write-protected cassette tape or floppy disk has been attempted. The cassette tape or floppy disk is protected against data writing. Action Release the write-protected state. (For cassette tape, fill in the hole on the tape surface with tape.
Return to Library ALARM No. Message 543 WNo. NOT FOUND ON PAPER TAPE Cause Action 544 ( , , 3 Type of error Stopped status Clearing procedure Display A L S Blue ) Loading or comparing is not possible since no O numbers (work numbers) are stored on the paper tape or floppy disk. Call the DATA I/O display (TAPE) and designate a work number(s). SET NEW PAPER TAPE ( , , ) A L S Blue 1. The tape reader/puncher is not correctly loaded with paper tape. Cause Action 2.
Return to Library 3 ALARM No. 551 Message PARITY V ERROR ( , , ) Type of error Stopped status Clearing procedure Display A L S Blue S Blue The contents of the paper tape or floppy disk cannot be read since they include a parity-V error(s). Cause E O B E O B E O B The number of sprocket holes in this area must be even. Action 552 Cause Make reading possible by making bit 1 of parity V-check valid/invalid parameter TAP25 invalid.
Return to Library ALARM No. 563 Cause Action Message PRINTER I/O ERROR (Cause, , ) 3 Type of error Stopped status Clearing procedure Display G L S Blue S Blue An error in printer communications has occurred during measurement result printing. - Check the printer for correct connection. - Check for differences in the RS-232C parameter settings between the printer and NC unit.
Return to Library 3 ALARM No. 572 Cause Message CANNOT LOAD (PROG SIZE EXCEED) (WNo., , ) Type of error Stopped status Clearing procedure Display A L S Blue S Blue The contents of the transmitted machining program from the host system are not correct. (More than 2000 lines of MAZATROL program data have been transmitted.) Action 573 Check the size of the program which has been transmitted from the host system. CANNOT LOAD (TOO MANY PROGRAMS) (WNo.
Return to Library ALARM No. 580 Cause Action 581 Cause Action 582 Cause Action 583 Cause Action Type of error Stopped status Clearing procedure Display ) A L S Blue Message CARD NOT READY ( , , 3 A memory card has not been correctly mounted in the NC unit. Check if the memory card is correctly mounted. DISK NOT READY ( , , ) A L S Blue ( , , ) A L S Blue A disk has not been correctly mounted. Correctly mount a disk in the disk drive.
Return to Library 3 ALARM No. Message 587 PROG. OPERATION NOT ALLOWED Cause (WNo., , ) Type of error Stopped status Clearing procedure Display A L S Blue 1. An attempt has been made to transmit a display inhibiting program to the host system. (Program management function) 2. An attempt has been made to transmit to the host system the program being edited (or the program being loaded using another I/O unit). 1. Check if the specified work number is for the program of display inhibition.
Return to Library ALARM No. 593 Message DNC I/O ERROR ( , , 3 Type of error Stopped status Clearing procedure Display G L S Blue ) - During use of DNC, processing has been aborted by line noise or other hardware factors. Cause - RS-232C communication parameter settings (such as those of the baud-rate, etc.) between the host system and NC unit differ. - Timer, number-of-retries or other settings are not correct. - Make line checks and hardware checks of the host system and NC unit.
Return to Library 3 ALARM 3-2-7 No. 600 - No. 699, No. 1600 - No. 1699 (MAZATROL program error) No. Message 600 —— Cause —— Action —— 601 Cause Action 602 Cause Action 603 SYSTEM ERROR ( , , ) ( , , ) Type of error Stopped status Clearing procedure Display E I (L) O (S) Red (Blue) A processing error has occurred within the NC unit. Using data I/O operation, save the program data, tool data, tool file data, parameters, etc. that are currently being used.
Return to Library ALARM No. 609 Cause Action 610 Cause Action 611 Cause Action 612 Cause Action 613 Cause Action 614 Cause Action 615 Cause Action 616 Cause Action 617 Message MISSING INPUT DATA (FACE) (WNo., UNo., SNo.) 3 Type of error Stopped status Clearing procedure Display B I (L) O (S) Red (Blue) O (S) Red (Blue) A face-machining unit lacks data. Review the particular machining program, and set data if a face-machining unit lacks data. MISSING TOOL DATA FOR POINT (WNo., UNo.
Return to Library 3 ALARM No. 618 Cause Action 619 Cause Action 620 Cause Action 621 Cause Action 622 Cause Action 623 Cause Action 624 Message POINT CUTTING PARAMETER ERROR Type of error Stopped status Clearing procedure Display B I (L) O (S) Red (Blue) B I (L) O (S) Red (Blue) I (L) O (S) Red (Blue) (WNo., UNo., SNo.) The point-machining parameter setting(s) is out of its permissible range. —— LINE/FACE CUTTING PAR. ERROR (WNo., UNo., SNo.
Return to Library ALARM No. 627 Cause Action 628 Cause Action 629 Cause Action 630 Cause Action 631 Cause Message TOOL DATA INPUT PROCESS ERROR 3 Type of error Stopped status Clearing procedure Display B I (L) O (S) Red (Blue) I (L) O (S) Red (Blue) I (L) O (S) Red (Blue) I (L) O (S) Red (Blue) (WNo., UNo., SNo.) The data of the tool length or tool diameter is not yet input on the TOOL DATA display. Review the tool data and input the tool length or tool diameter.
Return to Library 3 ALARM No. 636 Cause Action 637 Cause Action 638 Message STOCK REMOVAL Z TOO SMALL (WNo., UNo., SNo.) Type of error Stopped status Clearing procedure Display B I (L) O (S) Red (Blue) In the line- or face-machining unit, removal allowance Z is smaller than finish allowance Z. Review the line- or face-machining unit and increase removal allowance Z to a value greater than that of finish allowance Z. STOCK REMOVAL R TOO SMALL (WNo., UNo., SNo.
Return to Library ALARM No. 645 Cause Action Message PRIORITY No. OVERLAP (WNo., UNo., SNo.) 3 Type of error Stopped status Clearing procedure Display B I (L) O (S) Red (Blue) I (L) O (S) Red (Blue) The same priority number is assigned to different tools. Within one process, the same priority number must not be assigned to different tools. Change the priority number. 646 ILLEGAL PRIORITY NUMBER (WNo., UNo., SNo.)* (LNo. 1, LNo.
Return to Library 3 ALARM No. 653 Cause Action 654 Cause Action 655 Cause Action 656 Cause Action 657 Cause Action 658 Cause Action 659 Cause Action 660 Cause Action 661 Cause Action Message ILLEGAL TOOL DESIGNATED (WNo., UNo., SNo.) Type of error Stopped status Clearing procedure Display B I (L) O (S) Red (Blue) B I (L) O (S) Red (Blue) I (L) O (S) Red (Blue) Tools that cannot be used have been designated. Review the machining program and designate tools that are usable.
Return to Library ALARM No. 662 Cause Action 663 Message NO INCLINED PLANE OPTION (WNo., UNo., ) 3 Type of error Stopped status Clearing procedure Display B I (L) O (S) Red (Blue) An attempt has been made to execute the inclined-plane machining program in the absence of an inclined-plane machining option. Inclined-plane machining is not possible because of the absence of an inclined-plane machining option. WRONG HEAD ANGLE (WNo., UNo., ) B I (L) O (S) Red (Blue) 1.
Return to Library 3 ALARM No. Message 670 ILLEGAL SEQUENCE DATA IN PRG. Cause Action 671 Cause Action 672 Type of error Stopped status Clearing procedure Display B I (L) O (S) Red (Blue) B I (L) O (S) Red (Blue) I (L) O (S) Red (Blue) (WNo., UNo., SNo.) The tool sequence in the 3-D machining unit lacks of data. Review the machining program and input data to the tool sequence. ILLEGAL MOVE SURFACE DATA (WNo., UNo., SNo.
Return to Library ALARM No. 678 Message NO INTERSECTION (WNo., UNo., SNo.) Type of error Stopped status Clearing procedure Display B I (L) O (S) Red (Blue) Cause In the line- or face-machining unit, the coordinates of the intersection point of figures cannot be obtained because of shortage of, or contradiction, in the free-shape data. Action —— 679 Cause Action 680 Cause Action 681 CONNECTING CORNER IMPOSSIBLE (WNo., UNo., SNo.
Return to Library 3 ALARM No. 687 Cause Action 688 Cause Action 689 Cause Message NO FINISH POINT Type of error Stopped status Clearing procedure Display B I (L) O (S) Red (Blue) (WNo., UNo., SNo.) During input of free-shape data (open-figure data) to the line-machining unit, “?” has been set as the definition of the ending point. Review the machining program and set the coordinates of the ending point of the free shape. INSUFFICIENT INPUT DATA (WNo., UNo., SNo.
Return to Library ALARM No. 696 Cause Action 697 Cause Action 698 Cause Action 699 Cause Action Message ILLEGAL DIRECTION (WNo., UNo., SNo.) 3 Type of error Stopped status Clearing procedure Display B I (L) O (S) Red (Blue) O (S) Red (Blue) “Left” or “right” is set for the crossing point (P), though “up” or “down” should have been set. Review the machining program and check the value of the crossing point (P). DATUM
REQUIRED (WNo., UNo., SNo.
Return to Library 3 ALARM 3-2-8 No. 700 - No. 799, No. 1700 - No. 1799 (MAZATROL program error) No. Message 700 —— Cause —— Action —— 701 Cause Action 702 DEFINED SHAPE TOO SMALL ( , , Type of error Stopped status Clearing procedure Display B K O Blue ) (WNo., UNo., SNo.) The shape compensation clearance with respect to the shape of the endmilling-top is too large; or the tool diameter with respect to the size of the line-inside machining is too large.
Return to Library ALARM No. 708 Cause Action 709 Cause Action 710 Cause Action 711 Cause Action 712 Cause Action 713 Cause Action 714 Cause Action 715 Cause Action 716 Cause Action Message BLOCK DATA LIMIT EXCEEDED 3 Type of error Stopped status Clearing procedure Display B L S Blue L S Blue (WNo., UNo., SNo.) In the EIA program, the total number of characters within one block is in excess of 248. Divide the block so that one block contains 248 characters or less.
Return to Library 3 ALARM No. 717 Cause Action 718 Cause Action 719 Cause Action 720 Cause Action 721 Message SHAPE EXCEEDS MATERIAL SIZE (WNo., UNo., SNo.) Type of error Stopped status Clearing procedure Display B I (L) O (S) Red (Blue) The starting or ending point is outside the profile of the workpiece (approximate workpiece shape specified by common unit). Change the starting or ending point. CUTTING DIRECTION NOT DEFINED (WNo., UNo., SNo.
Return to Library ALARM No. 725 Cause Action 726 Cause Action 727 Cause Action 728 Cause Action 729 Cause Action 730 Cause Action 731 Cause Action 732 Cause Action 733 Cause Action Message ILLEGAL COMMON DATA (RADIAL) (WNo., UNo., SNo.
Return to Library 3 ALARM No. 734 Cause Action 735 Cause Action 736 Cause Action 737 Cause Action 738 Cause Action 739 Message ILLEGAL SHAPE EXCEEDS MTRL SIZE Type of error Stopped status Clearing procedure Display B I (L) O (S) Red (Blue) (WNo., UNo., SNo.) For machining of multiple grooves, the second and subsequent grooves are outside the workpiece profile defined by common unit. Reduce the number of grooves. ILLEGAL DESIGNATED TL WID (GRV) (WNo., UNo., SNo.
Return to Library ALARM No. 742 Message ILLEGAL THREAD HEIGHT (WNo., UNo., SNo.) 3 Type of error Stopped status Clearing procedure Display B I (L) O (S) Red (Blue) B I (L) O (S) Red (Blue) In the THREAD unit data, the following condition is not satisfied. (Finishing allowance) ≤ (Thread height) Cause Designated in the unit data. Set using parameter TC78.
Return to Library 3 ALARM No. Message 749 —— Action —— Cause Action 751 Cause Action 752 Stopped status Clearing procedure Display B I (L) O (S) Blue O (S) Blue I (L) O (S) Blue I (L) O (S) Blue —— Cause 750 Type of error CURVE DEFINITION ERROR (WNo., UNo., SNo.) A curved surface that cannot be machined has been defined. No corrective actions can be taken against this error; define a curved surface that can be machined. CURVE DEFINITION ERROR (WNo., UNo., SNo.
Return to Library ALARM No. 757 Message CURVE DEFINITION LARGE 3 Type of error Stopped status Clearing procedure Display B I (L) O (S) Red (Blue) (WNo., UNo., SNo.) 1. For rough-machining 2 with designation of workpiece size, the dimensions of the defined figure are larger than those of the workpiece. Cause Action 758 Cause Action 759 Cause Action 760 Cause Action 761 2.
Return to Library 3 ALARM No. 765 Cause Action 766 Message Z-OFFSET NOT FOUND (WNo., UNo., SNo.) Type of error Stopped status Clearing procedure Display B I (L) O (S) Red (Blue) The indispensable Z-offset is not yet set for a program of workpiece scheme (MILL & TURN) with Z-offset setting. Set the Z-offset item externally in the setup data page. MAXIMUM NO.OF LAYOUTS EXCEEDED (WNo., UNo., SNo.
Return to Library ALARM No. 774 Cause Action 775 Cause Action 776 Cause Action 777 Cause Action 778 Cause Action Message HEAD UNIT IN PROGRAM TOOL CANNOT PERFORM FACING Clearing procedure Display B I (L) O (S) Red (Blue) (WNo., UNo., SNo.) B I (L) O (S) Red (Blue) For tool selection on a turret-type tool-post: The section to be machined by the selected tool differs from the corresponding setting in the unit data line.
Return to Library 3 ALARM No. 783 Cause Action 784 Cause Action 785 Cause Action 786 Cause Action 787 Cause Action 788 Cause Action 789 Cause Action 790 Cause Action 791 Cause Action Message DBL SPDL OP ILLEGAL SIMUL OP Type of error Stopped status Clearing procedure Display B I (L) O (S) Red (Blue) O (S) Red (Blue) I (L) O (S) Red (Blue) I (L) O (S) Red (Blue) (WNo., UNo., SNo.) There is an instruction of simultaneous machining given in the flow of “2 Workpiece” machining.
Return to Library ALARM No. 792 Cause Action 793 Message ILLEGAL FEEDRATE (WNo., UNo., SNo.) 3 Type of error Stopped status Clearing procedure Display B I (L) O (S) Red (Blue) B I (L) O (S) Red (Blue) The feed data set in the tool sequence contains an invalid value. Set a correct feed data in the tool sequence. ILLEGAL MILL AXIS RPM (WNo., UNo., SNo.) If DRILL is selected as the turning drilingl unit tool: 1.
Return to Library 3 ALARM 3-2-9 No. 800 - No. 899, No. 1800 - No. 1899 (EIA/ISO program error) No. Message 800 —— Cause —— Action —— 801 Cause Action 802 Cause SIMULTANEOUS AXIS EXCEEDED ( , , Type of error Stopped status Clearing procedure Display B I (L) O (S) Red (Blue) ) (WNo., NNo., BNo.) The number of axis motion commands given in one block is in excess of the number of simultaneously controllable axes. Modify the program with respect to the specification concerned.
Return to Library ALARM No. 809 Cause Action 810 Cause Action 811 Cause Action 812 Cause Action 813 Cause Action 814 Cause Action 815 Cause Action 816 Cause Action 817 Cause Action Message ILLEGAL NUMBER INPUT 3 Type of error Stopped status Clearing procedure Display B I (L) O (S) Red (Blue) B I (L) O (S) Red (Blue) (WNo., NNo., BNo.) The assigned data for the address is out of the allowable setting range. Review the program. PROGRAM END NOT FOUND (WNo., NNo., BNo.
Return to Library 3 ALARM No. 818 Cause Action 819 Cause Action 820 Cause Action 821 Cause Action 822 Cause Action 823 Cause Action 824 Cause Action 825 Cause Action 826 Cause Action Message MISSING CENTER (NO DATA) (WNo., NNo., BNo.) Type of error Stopped status Clearing procedure Display B I (L) O (S) Red (Blue) O (S) Red (Blue) For arc interpolation by R designation, the coordinates of the center of the arc cannot be calculated. Correct the value of each address in the program.
Return to Library ALARM No. 827 Cause Action 828 Cause Action 829 Cause Action 830 Cause Action 831 Cause Action 832 Cause Action 833 Cause Action 834 Cause Action 835 Cause Action Message F0 COMMAND IN G02, G03 (WNo., NNo., BNo.) 3 Type of error Stopped status Clearing procedure Display B I (L) O (S) Red (Blue) The F 1-digit rapid-feed command (F0) has been specified during arc interpolation (G02 or G03).
Return to Library 3 ALARM No. 836 Cause Action 837 Cause Action 838 Cause Action 839 Message NO INTERSECTION (WNo., NNo., BNo.) Type of error Stopped status Clearing procedure Display B I (L) O (S) Red (Blue) In tool diameter offset (G41 or G42), the coordinates of the intersection point existing when a block was skipped in processing of interference blocks cannot be calculated. Review the program. TOOL OFFSET INTERFERENCE ERROR (WNo., NNo., BNo.
Return to Library ALARM No. 844 Cause Action 845 Cause Action 846 Cause Action 847 Cause Action 848 Cause Action 849 Cause Action 850 Cause Action 851 Cause Action 852 Cause Action Message PROGRAM No. NOT FOUND 3 Type of error Stopped status Clearing procedure Display B K S Blue B K S Blue (WNo., NNo., BNo.) An attempt was made to call a subprogram which was not yet registered. Register the subprogram. ILLEGAL VARIABLE COMMAND (WNo., NNo., BNo.
Return to Library 3 ALARM No. Message Type of error Stopped status Clearing procedure Display 853 EXTERNAL MACRO OPTION NOT FOUND (WNo., NNo., BNo.) B I (L) O (S) Red (Blue) Cause Action 854 Cause Action 855 Cause Action 856 Cause Action 857 Cause Action 858 Cause Action 859 Cause Action 860 Cause Action 861 Cause Action A user macro interruption command has been designated although such interruption specifications are not provided. Check the specifications.
Return to Library ALARM No. 862 Cause Action 863 Cause Action 864 Cause Action 865 Cause Action 866 Cause Action 867 Cause Action 868 Cause Action 869 Message INTEGER VALUE OVERFLOW Type of error Stopped status Clearing procedure Display B I (L) O (S) Red (Blue) (WNo., NNo., BNo.) The integral value has overstepped –231 (231 –1) in the operation process.
Return to Library 3 ALARM No. 871 Cause Action 872 Cause Action 873 Cause Action 874 Cause Action 875 Cause Action 876 Cause Action 877 Cause Action 878 Cause Action 879 Cause Action Message VARIABLE NAME EXISTS (WNo., NNo., BNo.) Type of error Stopped status Clearing procedure Display A K (L) P (S) Red (Blue) B I (L) O (S) Red (Blue) There are overlapping variables names. Correct the program so that variables names do not overlap. G51 OPTION NOT FOUND (WNo., NNo., BNo.
Return to Library ALARM No. 880 Cause Action 881 Cause Action 882 Cause Action 883 Cause Message AXIS NOT ZERO RETURNED (WNo., NNo., BNo.) 3 Type of error Stopped status Clearing procedure Display B I (L) O (S) Red (Blue) A move command other than that for reference-point return has been designated for the axis that was not returned to its reference point. Manually return the axis to its reference point. G30 OPTION NOT FOUND (WNo., NNo., BNo.
Return to Library 3 ALARM No. 889 Cause Action 890 Cause Action 891 Cause Action 892 Cause Action 893 Cause Action 894 Cause Message G37 OPTION NOT FOUND (WNo., NNo., BNo.) Type of error Stopped status Clearing procedure Display B I (L) O (S) Red (Blue) The automatic tool-length measurement command (G37) has been designated although such measurement specifications are not provided. Check the specifications. G31 OPTION NOT FOUND (WNo., NNo., BNo.
Return to Library ALARM No. 898 Cause Action 899 Cause Action Message LAP CYCLE ILLEGAL SHAPE DESIGN. ( , , ) Type of error Stopped status Clearing procedure Display B J P Red P Red The shape defined in the turning fixed-cycle (G270 through G273) is not the shape for correct cutting. Recheck the shape data specified by the turning fixed-cycle (G270 through G273).
Return to Library 3 ALARM No. 1800 Message CANNOT CHANGE TIME CONSTANT (WNo., NNo., BNo.) Type of error Stopped status Clearing procedure Display B I P Red The G-command has been set in the block containing a time constant changeover/cancellation command. Cause The time constant changeover/cancellation command has been set in the fixed cycle.
Return to Library ALARM 3 3-2-10 No. 900 - No. 999, No. 1900 - No. 1999 (EIA/ISO program error) No. Message 900 —— Cause —— Action —— 901 Cause Action 902 Cause Action 903 Cause Action 904 INCORRECT FIXED CYCLE COMMAND ( , , Type of error Stopped status Clearing procedure Display B I (L) O (S) Red (Blue) ) (WNo., NNo., BNo.) The fixed-cycle command has been set in the program during the tool diameter offset (G41 or G42) modal status.
Return to Library 3 ALARM No. 909 Cause Action Message ILLEGAL PITCH IN FIXED CYCLE —— —— Action —— Action 912 Cause Action 913 Cause Action 914 Cause Action 915 Cause Action 916 Cause Action 917 Cause Action Clearing procedure Display B I (L) O (S) Red (Blue) Check and correct the pitch or the number of threads. Cause Cause Stopped status The pitch or the number of threads designated for the tapping cycle (G74 or G84) of the drilling fixed cycles is wrong. 910 911 (WNo., NNo.
Return to Library ALARM No. 918 Cause Action 919 Cause Action 920 Cause Action 921 Cause Action 922 Cause Action 923 Cause Action 924 Cause Action 925 Cause Action 926 Cause Action Message INCORRECT ANGLE DATA (WNo., NNo., BNo.) 3 Type of error Stopped status Clearing procedure Display B J (L) P (S) Red (Blue) In address designation of the geometric command, the angle in the first block, ending point coordinates and angle in the second block are incorrectly given.
Return to Library 3 ALARM No. 927 Cause Action 928 Cause Action 929 Cause Action 930 Cause Action 931 Cause Action Message SKIP COMMAND IN CORRECTING DIA Type of error Stopped status Clearing procedure Display B I (L) O (S) Red (Blue) (WNo., NNo., BNo.) The skip command (G31) was given during tool diameter offset (G41 or G42). Correct the program so that the skip command is executed only after the cutter-diameter compensation cancellation command (G40) has been executed.
Return to Library ALARM No. 936 Message OPTION NOT FOUND (WNo., 0, 0) 3 Type of error Stopped status Clearing procedure Display E I (L) O Red Either of the following seven options is missing (identify the corresponding option from the work number displayed in parentheses): Cause Action 937 Cause Action 938 Cause Action 939 Cause Action 940 Cause Action 941 Cause Action 942 Cause Action 1. 2. 3. 4. 5. 6. 7.
Return to Library 3 ALARM No. 944 Cause Action Message WRONG CMD. IN 3-D COORDINATES (WNo., NNo., BNo.) Type of error Stopped status Clearing procedure Display B I (L) O (S) Red (Blue) A G68 command has been designated during the modal information that does not permit G68 to be set. Review the program, and modify the modal information existing when the G68 command was designated. 945 Cause Action NO HV MACHINING FUNC. OPTION (WNo., NNo., BNo.
Return to Library ALARM No. 953 Cause Action 954 Cause Action 955 Message TOOL DATA INPUT PROCESS ERROR ( , , ) Type of error Stopped status Clearing procedure Display B I (L) O (S) Red (Blue) During the execution of EIA/ISO program or of MDI, the tool data was found not to include LENGTH or ACT-φ (NOM-φ) (this, however, applies only if bit 7 of parameter F84 is set to “1” for the use of MAZATROL tool length and tool diameter data). Recheck the tool data and set missing values.
Return to Library 3 ALARM No. 962 Cause Action 963 Cause Action Message CANNOT USE 5X RADIUS COMP. Type of error Stopped status Clearing procedure Display B I (L) O (S) Red (Blue) (WNo., NNo., BNo.) A command of tool diameter offset for five-axis machining has been designated under incompatible modal conditions. Review the program, and delete the illegal G-code.
Return to Library ALARM No. 974 Message TOOL TIP PT CTRL FORMAT ERROR 3 Type of error Stopped status Clearing procedure Display B J (L) P (S) Red (Blue) (WNo., NNo., BNo.) 1. Arguments I, J, and K are specified in the mode of G43.4, or a command of rotary axis motion is given under G43.5. Cause 2. The code G49 is given in a block with other commands. 3. A rotary axis is specified in the mode of circular interpolation. 1.
Return to Library 3 ALARM No. 984 Cause Action 985 Cause Action 986 Cause Action 987 Cause Action 988 Cause Action 989 Cause Action 990 Cause Message MACRO USER ALARM 5 ( , , Type of error Stopped status Clearing procedure Display B I (L) O (S) Red (Blue) I (L) O (S) Red (Blue) I (L) O (S) Red (Blue) I (L) O (S) Red (Blue) I (L) O (S) Red (Blue) I (L) O (S) Red (Blue) I (L) O (S) Red (Blue) ) #3000 = 5 (alarm message) in the user macroprogram was executed.
Return to Library ALARM No. 992 Cause Message MACRO MEASUREMENT ALARM 3 ( , , 3 Type of error Stopped status Clearing procedure Display B I (L) O (S) Red (Blue) ) 1. Correct signals were not output because of trouble with the touch sensors, receivers or other such MMS unit components. 2. #3000 = 13 (alarm message) in the user macroprogram was executed. Action 1. Contact Mazak Technical Center or Technology Center. 2.
Return to Library 3 ALARM No. 1991 Message NOT POSSIBLE CROSS MACHINING (WNo., NNo., Cause) Type of error Stopped status Clearing procedure Display B I (L) O (S) Red (Blue) During the tool path check, the system in which the crossing command was set and/or the remote system for which the crossing command was to be executed has been set to the following status: 1: The specified axis does not exist in the remote system.
Return to Library ALARM 3 3-2-11 No. 2100 - No. 2199 (Interference error) No. 2100 Cause Action 2101 Cause Action 2102 Cause Action Message MACN INTRF (WNo., UNo., SNo.) Type of error Stopped status Clearing procedure Display A L S Blue Execution of the machining program results in the interference occurring between and . Review and correct the program. NEAR MISS (WNo., UNo., SNo.
Return to Library 3 ALARM No. 2130 Message CANNOT DISPLAY WORKPIECE MODEL ( , , ) ( , , ) ( , , ) Type of error Stopped status Clearing procedure Display A L S Blue A L S Blue A L S Blue L S Blue 1. Lack of available memory space Cause 2. Arithmetical incapability 3. Entered data imperfections 1. Divide the program. Action 2. Confirm parameters. 3. Confirm tool data. Cause Action 2140 CANNOT DISPLAY MACHINE MODEL 1. Lack of available memory space Cause 2.
Return to Library M-CODE LIST 4 M-CODE LIST For description of M-codes, refer to the Operating Manual of the machine.
Return to Library 4 M-CODE LIST - NOTE - 4-2 E
