Installation Guide

ManualsBrandsSafety Technology International ManualsAlarm SystemsWireless Exit Stopper Multifunction Door Alarm System for Double Doors

- 1 -

Exit Stopper

STI-6400 Series

Features

· Helps prevent unauthorized exits/entries through doors.

· Easy to install. Warning sound when turning on (two ﬂashes/beeps) and off

(one ﬂash/beep).

· Add warning in second language with provided labels (21 languages).

· Select volume, alarm duration and delay settings.

· Mount on top, right, left or next to almost any door.

· Select on-site whether to use an alarm or annunciator.

· Low battery detection, beep and ﬂashes.

· Alarm sounds and high power LED light ﬂashes when activated.

· Dry contact Form C relay.

· Protect anything such as cabinet, extinguisher, etc. with an external reed or

any mechanical switch.

Rely on STI

Summary of content (8 pages)

PAGE 1
Exit Stopper® STI-6400 Series Features · · · · · · · · · · Helps prevent unauthorized exits/entries through doors. Easy to install. Warning sound when turning on (two flashes/beeps) and off (one flash/beep). Add warning in second language with provided labels (21 languages). Select volume, alarm duration and delay settings. Mount on top, right, left or next to almost any door. Select on-site whether to use an alarm or annunciator. Low battery detection, beep and flashes.
PAGE 2
Warnings All units are recommended for indoor use only. Unit must be tested periodically to verify the life of battery. STI recommends you change the 9 Volt battery twice a year. To hear alarm when normal work environment is loud, may need to purchase remote horns. When purchasing a remote unit (STI-6403 or STI-6404) you will need to periodically test the connections to make sure audibles function at a sound level to alert staff. Maximum of three remote alarms may be used in parallel.
PAGE 3
Specifications Polycarbonate Enclosure Dimensions 5.375” W x 5.375” H x 2 “ D (137mm x 137mm x 51mm) Flammability UL94 V-2 Wall Thickness 0.12 in (3.
PAGE 4
Circuit Board Set-up Remote Power Switch Settings (defaults shown) Form C Relay RS1 RS2 KEYSW All models are shipped with jumper across RS2 terminals for use with one reed switch. If using second reed switch, remove jumper wire and insert second reed switch.
PAGE 5
Alarm Feature Description Switch settings – factory default listed first 1 OFF = arming immediate (ON for 15 second delay) 2 OFF = trip immediate (ON for 15 second delay) 3 OFF = shut-off based on switches #4 and #5 (ON shut-off approx. 3 sec. after door closes) 4 OFF and Switch 5 OFF = duration 30 sec. (other options 4 OFF and 5 ON = duration 180 sec., 4 ON and 5 OFF duration continuous, 4 ON and 5 ON = annunciator beeps) 6 OFF = low battery detection.
PAGE 6
BASE TAMPER WRENCH (1) PROVIDED Installation Instructions (continued) 4. Mount magnet using hardware provided. Magnet must be within ¾” of the reed switch when door is closed. Please refer to figures 8, 9 and 10 for other mounting options. Note: When mounting on metal doors or door frame, use plastic spacers provided. 5. If installing STI-6402, STI-6403, STI-6404 or STI-6405 continue to page 6. 6.
PAGE 7
STI-6404 Double Door with Remote Horn Install Notes The STI-6404 is a combination unit for double doors with a remote horn. Reference the installation instructions for the main unit, the STI-6402 and the STI-6403 for complete installation. STI-6405 Exit Stopper with Momentary Reset The STI-6405 uses a momentary switch. After initial installation, unit is always on and you do not have to remember to turn it on when you leave a protected area.
PAGE 8
TYPICAL RECESSED MOUNT DOORJAMB INSTALLATION MAGNET ASSEMBLY (SEE ABOVE FOR INSTALLATION) 3/4 in. (19mm) MAXIMUM GAP DOOR STOP MAGNET 6400 SWING DOOR SWING *Note: When mounting reed switch on door and the main unit on wall, wire service loop must be used.