Register your product and get support at 02 English www.philips.com/welcome Type HD8838 SUP 037DRJ 02 EN OPERATING INSTRUCTIONS READ THESE INSTRUCTIONS CAREFULLY BEFORE USING THE MACHINE.
IMPORTANT SAFEGUARDS When using electrical appliances, basic safety precautions should always be followed, including the following: 1. Read all instructions. 2. Do not touch hot surfaces. Use handles or knobs. 3. To protect against fire, electric shock and injury to persons do not immerse cord, plugs, or appliance in water or other liquid. 4. Close supervision is necessary when the appliance is used by or near children. 5. Unplug from outlet when not in use and before cleaning.
CAUTION This appliance is for household use only. Any servicing, other than cleaning and user maintenance, should be performed by an authorized service center. Do not immerse machine in water. To reduce the risk of fire or electric shock, do not disassemble the machine. There are no parts inside the machine serviceable by the user. Repair should be done by authorized service personnel only. 1. Check voltage to be sure that the voltage indicated on the nameplate corresponds with your voltage. 2.
GENERAL INFORMATION The coffee machine is suitable for preparing espresso coffees using coffee beans; it is equipped with a device to dispense steam and hot water. The structure of the machine with its elegant housing has been designed for domestic use only and is not suitable for continuous professional-type operation. Keep these operating instructions in a safe place and make them available to anyone who may use the coffee machine.
Danger of burns Never direct the jet of hot steam and/or hot water towards yourself or others: Danger of scalding! Always use the handles or knobs provided. Milk Container At first use or after a long period of inactivity wash all components of the milk container to guarantee good operation and to avoid proliferation of bacteria, harmful to health. The milk in the carafe may be stored inside the carafe using the instructions and precautions on the original package.
Grinder adjustment knob Coffee bean hopper cover Service door Coffee bean hopper Control Panel Pre-ground coffee compartment Coffee / hot water / Cappuccino dispensing spout Cup holder grill Full drip tray indicator Brew Group Milk container coupling Coffee grounds drawer Milk Container Power button Drip tray Water hardness test Water tank Grease for the Brew Group Pre-ground coffee doser Power cord Strong coffee brew button Long coffee brew button Cappuccino / hot milk brew button •4• LCD Display
TABLE OF CONTENTS • GENERAL INFORMATION .........................................2 • SAFETY REGULATIONS ............................................2 • INSTALLATION ........................................................5 Machine Packaging ..............................................................5 Preliminary Operations ........................................................5 • RINSE/SELFCLEANING CYCLE .................................
• Remove the water tank from its place. • Rinse and fill it with fresh water making sure that it is not filled exceeding the (MAX) level indicated in the tank. Put the tank back in its place. • The display shows the ON/OFF icon. Black • Make sure the selector switch is on “ ” position; if necessary, turn it to the indicated position. • To turn the machine on simply press the ON/OFF button. Fill the tank only with fresh, non-sparkling water.
USING THE MACHINE FOR THE FIRST TIME OR AFTER A LONG PERIOD OF INACTIVITY 8 Turn the selector switch clockwise and set it to the “ ” position. These simple operations will make it possible to always brew excellent coffee. 1 Place a large container under the dispensing spout. The following icon will be displayed. Press button “ “ to start dispensing hot water. 2 Before starting the procedure, check that the following icon is displayed.
“INTENZA” WATER FILTER Press the “ ” button until the following page is displayed. To improve the quality of the used water, it is advisable to install the water filter. Remove the water filter from its packaging, immerse it vertically (with the opening positioned upwards) in cold water and delicately press the sides so as to let the air bubbles out. Remove the small white filter from the tank and store it in a dry place sheltered from dust.
WATER HARDNESS MEASUREMENT The water hardness measurement is very important in order to correctly manage the “Intenza” filter and the frequency with which the machine must be descaled. Immerse the water hardness test strip provided with the machine in water for 1 second. Note: The test strip is only valid for one measurement. Check how many squares change colour and refer to the table. The letters correspond to the references that are located in the base of the Intenza filter.
COFFEE BREWING • Two cups/mugs can be placed under the dispensing spout for brewing two coffees at the same time. Note: Should the machine not brew coffee, make sure that the water tank contains water. Before brewing coffee check the lights on the display and make sure the water tank and coffee bean hopper are full. Green Leave the selector switch on the coffee position “ ” during the brewing phase.
Using Coffee Beans • To brew coffee, press and release: the “ ” button to select the desired Aroma. ” button for an espresso cofthe “ fee; the “ ” button for a long coffee. • Then, the brewing cycle starts. Green Green To brew 2 cups of coffee, press the desired button twice. The machine manages the brewing cycle automatically. • Coffee brewing stops automatically when the pre-programmed level is reached; however, it is possible to interrupt coffee brewing by pressing the button initially pressed.
CAPPUCCINO Danger of scalding! Brewing may be preceded by small jets of hot water. Place the cup you use every day to enjoy your cappuccino. Important note: Immediately after using the machine to brew a cappuccino, clean all components as described in the "Cleaning of the Milk Brewing System" section. After filling the milk container, place it in the machine. Insert the container pin in its seat.
Press the “ Each brewing phase is programmed, but can be interrupted in advance by pressing the “ ” button. “ button. • Once milk has been brewed, the machine brews the coffee. • The following icon is displayed during the preheating time required by the machine: Orange Green In this phase the machine starts grinding coffee and/or gets ready to brew coffee. • When the following icon is displayed, the machine brews frothed milk directly in the cup.
Milk, even UHT milk, goes bad easily at room temperature; therefore, it is recommended to DO NOT keep it at room temperature for long periods. Furthermore, the milk carafe has always to be put back in the fridge when it is not needed. It is also advisable to keep the parts in contact with the milk cleaned following the directions and recommendations described in these instructions.
After having brewed milk for some times, turn the main knob to the right as for hot water dispensing: the image "CLEAN+” will appear. Place a container under the dispensing spout and push the upper link button to start the cleaning operation. Then, bring the knob back to the central position to allow other brewing programmes.
PERIODIC CLEANING Proceed as follows for the parts installed on the carafe. • Remove the carafe from the machine. • Lift the cover and pay attention that the wand does not splash the remaining milk. • Remove the wand from the cover. • Remove the pin: - Rotate it counter-clockwise. - Take off the pin from the cover. • Wash the cover and the carafe with lukewarm water. • Wash the wand and the pin of the machine by running lukewarm water inside the duct.
Proceed as follows to complete the cleaning process: 1 Remove the top cover paying attention to the suction pipe. 2 Fill the container with lukewarm water: Do not exceed the MAX level indicated on the container. 3 Replace the suction pipe inside the container and close the cover by pressing it to the end. C L E A N I N G O F T H E M I L K Place the cup you use every day to enjoy your hot milk. Press the “ ” button until the following page is displayed. Press the “ ” button to start dispensing water.
HOT WATER DISPENSING Warning: At the beginning, short spurts of hot water may come out. Danger of scalding. To reset the machine to normal operation turn the selector switch counterclockwise until it is set to the “ ” position. • Before dispensing hot water, check that the following icon is displayed: Green When the machine is ready, proceed as follows: • Place a container under the dispensing spout. Orange • Turn the selector switch clockwise and set it to the “ position.
ADJUSTMENTS The machine that you have bought allows for certain adjustments that will permit you to use it to its full potential. any type of operation inside the coffee bean hopper. Do not pour coffee beans when the coffee grinder is working. Saeco Adapting System Coffee is a natural product and its characteristics may change according to its origin, blend and roast.
ADJUSTMENTS • Press and hold the “ ” button until the (MEMO) icon is displayed. At this point, the machine is programming it. • The machine begins the brewing phase. The “ ” icon will be displayed to show which button is being programmed. • From now on, press the button with the “ ” icon each time the desired amount of coffee is reached in the cup.
The “ Adjusting the amount of frothed milk The machine allows you to adjust the amount of dispensed milk according to your taste and/or the size of your cups. Green ” icon will appear on the display. From now on, press the “ ” button each time the desired amount of milk is reached in the cup. Whenever you wish, it is possible to brew a programmed amount of frothed milk in your favourite cup. This amount may be reprogrammed to your taste.
PROGRAMMING The user can change some of the machine operating parameters to suit his/ her needs. Programming controls Changes can be made on each page: Enter the “menu” The programming menu can be accessed at any time when the machine is turned on and ready to be used. Orange Green - The “ ” and “ ” buttons allow changing the value of the function, among those present on the page. To access the programming menu, turn the selector switch counter-clockwise and set it to the “ ” position.
Functions Programming Example COFFEE TEMPERATURE This function allows you to adjust the coffee brewing temperature. In this example, we want to explain how to programme the display contrast. Proceed in a similar manner to change the other functions. Orange With the machine turned on, access the programming menu, turn the selector switch counter-clockwise and set it to the “ ” position.
CLEANING AND MAINTENANCE General Cleaning Brew Group • Empty and clean the coffee grounds drawer daily, with the machine turned on. • The Brew Group should be cleaned every time the coffee bean hopper is filled or at least once a week. • Turn off the machine by pressing the ON/OFF button and remove the plug from the socket. • Remove the coffee grounds drawer. Open the service door.
Lubricate the Brew Group after approximately 500 brewing cycles. The grease to lubricate the Brew Group may be purchased at authorised service centres. • Lubricate the brew group guides using the supplied grease only. • Apply the grease evenly on both side guides. • Insert the Brew Group in its seat until it locks into place WITHOUT pressing the "PUSH" button. • Insert the coffee grounds drawer. Close the service door.
DESCALING Limescale normally builds up with the use of the appliance. The display informs you when descaling is necessary: Orange In case of conflict, priority must be given to what is indicated in the operation and maintenance manual over the instructions provided on separately sold accessories and materials. • Then, the page appears on the display to start descaling. Orange • Press the “ “ button to enter the descaling menu. If you press the “ ” button by mistake, use the same button to quit.
Red Red Note: The descaling cycle may be paused by pressing the “ “ button. To resume the cycle, press the button again. This allows you to empty the container or to go away for a short period of time. • When the solution in the tank is finished, the icon on the side is displayed. • The icon indicates that the tank must be rinsed and filled. Rinse the water tank thoroughly and refill it with fresh drinking water.
CONTROL PANEL DISPLAY Ready Signals • The machine is ready for brewing coffee and • The machine is brewing a cappuccino with cappuccino with coffee beans. Green ground coffee. Green • The machine is ready for brewing coffee and • The machine is programming the amount of cappuccino with pre-ground coffee. Green coffee to be brewed. Green • The machine is ready for hot milk brewing. • The machine is programming the amount of hot milk to be brewed.
Alarm Signals • Start screen for descaling cycle activation. • Close the service door. Press “ESC” to quit. Red Red • No coffee beans in the coffee bean hopper. • Descaling cycle in progress. After refilling the hopper, the cycle can be restarted. Red Red • Turn the machine off. After 30 seconds, turn • Descaling cycle PAUSED. it back on. Try this 2 or 3 times. Red If the machine does NOT start, contact an authorised service centre.
CONTROL PANEL DISPLAY Warning Signals • The machine is warming up to brew coffee • The machine needs the milk system to be and dispense hot water and steam. Orange cleaned. Refer to section “CLEANING OF THE MILK BREWING SYSTEM”. Orange After washing the milk group, press the “ ” button to cancel the warning. • The machine is performing the rinse cycle. Wait until the machine stops the operation. • The Brew Group is being reset due to machine reset. Orange • The machine needs a descaling cycle.
TROUBLESHOOTING Machine Actions Causes The machine does not turn on. The machine is not connected to the electric net- Connect the machine to the electric network. work. The cups are cold. Preheat the cups with hot water. The milk group is clogged. Clean the milk group. Make sure that the machine is turned off and has cooled before performing this operation.
• 32 •
• 33 •
02 EC DECLARATION OF CONFORMITY YEAR 09 EC 2006/95, EC 2004/108, SAECO INTERNATIONAL GROUP S.P.A. Via Torretta, 240 - 40041 Gaggio Montano (BO) - Italy we declare under our sole responsibility that the following product: AUTOMATIC COFFEE MACHINE MACHINE DISPOSAL - The packing materials can be recycled. - Appliance: Unplug the appliance and cut the power cord. - Deliver the appliance and power cord to a service center or public waste disposal facility. This product complies with eu directive 2002/96/ec.
