SDS

Date Printed: 2/14/2017
4. First-aid Measures
FIRST AID - EYE CONTACT: Immediately flush eyes with plenty of water for at least 15 minutes holding eyelids open. Get medical
attention. Do NOT allow rubbing of eyes or keeping eyes closed.
FIRST AID - SKIN CONTACT: Wash skin with soap and water. Remove contaminated clothing. Get medical attention if irritation
develops or persists.
FIRST AID - INHALATION: Remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give oxygen.
Get immediate medical attention. Do NOT use mouth-to-mouth resuscitation. If you experience difficulty in breathing, leave the
area to obtain fresh air. If continued difficulty is experienced, get medical assistance immediately.
FIRST AID - INGESTION: If swallowed, rinse mouth with water. If feeling unwell, get medical attention. Swallowing less than an
ounce will not cause significant harm. For larger amounts, do not induce vomiting, but give one or two glasses of water to drink and
get medical attention.
5. Fire-fighting Measures
EXTINGUISHING MEDIA: Alcohol Film Forming Foam, Carbon Dioxide, Dry Chemical, Dry Sand, Water Fog
UNUSUAL FIRE AND EXPLOSION HAZARDS: Keep containers tightly closed. FLASH POINT IS TESTED TO BE GREATER
THAN 200 DEGREES F. No unusual fire or explosion hazards noted.
SPECIAL FIREFIGHTING PROCEDURES: Water may be used to cool closed containers to prevent buildup of steam. If water is
used, fog nozzles are preferred.
6. Accidental Release Measures
STEPS TO BE TAKEN IF MATERIAL IS RELEASED OR SPILLED: If spilled, contain spilled material and remove with inert
absorbent. Dispose of contaminated absorbent, container, and unused contents in accordance with local, state, and federal
regulations. Do not incinerate closed containers
7. Handling and Storage
HANDLING: Wash thoroughly after handling. Wash hands before eating. Remove contaminated clothing and launder before reuse.
Use only with adequate ventilation. Follow all MSDS/label precautions even after container is emptied because it may retain product
residues. Avoid breathing fumes, vapors, or mist. Avoid contact with eyes, skin and clothing.
STORAGE: Store in a dry, well ventilated place. Keep container tightly closed when not in use.
8. Exposure Controls/Personal Protection
Chemical Name CAS-No.
Weight %
Less Than
ACGIH TLV-
TWA
ACGIH TLV-
STEL
OSHA PEL-
TWA
OSHA PEL-
CEILING
Crystalline Silica / Quartz 14808-60-7 55.0 0.025 mg/m3 N.E. 50 µg/m3 N.E.
2,2,4-Trimethyl-1,3-Pentanediol
Isobutyrate
25265-77-4 1.0 N.E. N.E. N.E. N.E.
Distillates (Petroleum) Solvent-
Dewaxed Heavy Paraffinic
64742-65-0 1.0 N.E. N.E. N.E. N.E.
PERSONAL PROTECTION
ENGINEERING CONTROLS: Use process enclosures, local exhaust ventilation, or other engineering controls to control airborne
levels below recommended exposure limits. Prevent build-up of vapors by opening all doors and windows to achieve cross-
ventilation.
RESPIRATORY PROTECTION: A respiratory protection program that meets OSHA 1910.134 and ANSI Z88.2 requirements must
be followed whenever workplace conditions warrant a respirator's use.
SKIN PROTECTION: Use gloves to prevent prolonged skin contact. Nitrile or Neoprene gloves may afford adequate skin
protection.
EYE PROTECTION: Use safety eyewear designed to protect against splash of liquids.
OTHER PROTECTIVE EQUIPMENT: Refer to safety supervisor or industrial hygienist for further guidance regarding types of
personal protective equipment and their applications.
Page 2 / 5