Use and Care Manual

ManualsBrandsRust-Oleum OKON ManualsBuilding materials1-gal. Acrylic Multi-Surface Water Repellent Clear Sealer (6-Pack)

TECHNICAL DATA OKN-07

OKON MULTI-SURFACE WATER REPELLENT SEALER™

MULTI-SURFACE WATER REPELLENT AND SEALER FOR

CONCRETE, WOOD, BRICK & STUCCO

MASONRY

Form: JPB-07

Rev.: 060213

.DESCRIPTION AND USES .

OKON WATERPROOFING SEALER is a easy-to-use

multi-surface water repellent AND sealer. It helps

protect porous concrete or wood from the damaging

effects of water absorption. Water is a major cause

ofpremature deterioration of many building materials. In

concrete water causes efflorescence, mold, freeze-thaw

damage, dusting and staining. In wood water absorption

causes splitting, cracking, warping rotting and mold.

MULTISURFACE helps prevent these occurrences by

significantly reducing water absorption. Unlike simple

wax-based repellents, MULTISURFACE is an

acrylic/siloxane blend that provides protection long after

the initial water-beading action has ended. A single

application can last one to three years and can be easily

refreshed with another application. See application

instructions and label limitations for details.

PRODUCTS .

SKU Container Size

OK-931 Gallon

OK-930 5-Gallon

OK-935 Drum

.FEATURES .

For use on porous surfaces including: Concrete,

wood, stucco, brick, adobe, Canvas, plywood,

pottery.

Protects many types of structures: Walls. Floors,

fences, decks, siding, patios, sidewalks.

Combines proprietary water-repellent with

100%acrylic resin and siloxane.

Paintable ATM D 3359

Breathable ASTM 1653

Very low odor, low VOC and cleans up with soap

and water.

Long lasting protection – 1-3 years depending on

substrate and exposure conditions.

.PRODUCT APPLICATION .

SURFACE PREPARATION

MULTISURFACE requires minimal surface preparation

and can be applied to most porous surfaces that are

clean (free of dirt, waxes and oils), non-glossy and free

from sub-surface moisture.

Porous: Test the porosity of the surface by sprinkling with

water. If the surface turns dark as the water is absorbed

MULTISURFACE can be applied.

Clean: Sweep and hose-off exterior surfaces; vacuum and

damp-mop interior surfaces. Use a degreaser to remove

oil or grease stains. Use JOMAX® to remove exterior

mildew and a wood brightener to remove gray weathered

wood fibers.

PRODUCT APPLICATION (cont.)…………

Sub-surface moisture: Do not apply to interior floors where

sub-surface moisture is present. To test for moisture,

conduct a test by simply taping a piece of 4 mil plastic

sheet 18" by 18" on the bare concrete for 24 hours. Be

sure to tape all four sides. After 24 hours, check the

concrete for signs of moisture. The concrete will be darker

if damp. A dark surface under the plastic indicates

moisture and MULTISURFACE should not be applied:

Exterior pitted concrete, exposed aggregate and

sandstone absorb and hold moisture unless totally sealed.

MULT SURFACE should not be used on these surfaces in

areas where freezing occurs. New concrete must be cured

for 28 days prior to coating. The surface must be

thoroughly rinsed if applied over acid stain or if surface

was acid etched. Un-rinsed acid salts may cause whitish-

blotches to appear.

COVERAGE

The spread-rate of OKON Waterproofing Sealer will

vary with the porosity and texture of the surface. A second

coat may be applied if the surface is still absorbent.

.APPLICATION

MULTISURFACE is ready-to-use, no thinning is required.

It can be applied by brush, roller or garden-type sprayer.

Do not pour product onto surface to spread. Apply a

uniform wet coat at the estimated spread rate. It appears

milky-white when applied but dries clear. Material that is

not absorbed should be back rolled or brushed out to

avoid build up. Do not allow puddles, drips or runs to dry

on the surface. MULTISURFACE may slightly darken the

surface and add a slight sheen. Stop application at

expansion joints, walls or breaks defined with masking

tape. The surface temperature at time of application is

very important.

CLEAN UP

Clean hands and tools with soapy water. Drips and runs

that have dried may be removed using a strong solvent

within 24 hours after application. After that time sanding

may be necessary.

LIMITATIONS

Do not use on driveways, flagstone, or non-porous

materials. OKON WATERPROOFING SEALER

(MULTISURFACE) does not provide protection against

hydrostatic water pressure, wind driven rain, or

efflorescence. Tinting MULTISURFACE is not

recommended. Where a higher performance product is

needed – light weight or split face block - use OKON W-2

or OKON PLUGGER.

Summary of content (3 pages)

PAGE 1
TECHNICAL DATA OKN-07 OKON MULTI-SURFACE WATER REPELLENT SEALER™ MASONRY MULTI-SURFACE WATER REPELLENT AND SEALER FOR CONCRETE, WOOD, BRICK & STUCCO .DESCRIPTION AND USES PRODUCT APPLICATION (cont.)………… . OKON WATERPROOFING SEALER is a easy-to-use multi-surface water repellent AND sealer. It helps protect porous concrete or wood from the damaging effects of water absorption. Water is a major cause ofpremature deterioration of many building materials.
PAGE 2
TECHNICAL DATA OKN-07 OKON MULTI-SURFACE WATER REPELLENT SEALER™ MULTI SURFACE WATER REPELLENT SEALER FOR CONCRETE, WOOD, BRICK & STUCCO .PRODUCT APPLICATION (cont.) . WARRANTY The manufacturer will replace this product if, within 60 days of the date of purchase, it is shown to be defective when used as directed.
PAGE 3
TECHNICAL DATA OKN-07 OKON MULTI-SURFACE WATER REPELLENT SEALER™ MULTI SURFACE WATER REPELLENT SEALER FOR CONCRETE, WOOD, BRICK & STUCCO .PHYSICAL PROPERTIES . OKON MULTI-SURFACE WATER REPELLENT SEALER Resin Type Acrylic / Siloxane Color Milky White in Can / Clear on Surface Solvents Weight Water Per Gallon 8.4 lbs. Per Liter 1.00 kg Solids by weight 8% Volatile Organic Compounds <67 g/l (0.56 lbs./gal.) Application Parameters Initial Coat Spread Rate (assume 15% material loss) [sq. ft.