Installation Guide

Notice
Parameter
Installation Steps
INSTALLATION INSTRUCTION
3. Connect the hot and cold inlet hoses onto the matching
water valves and secure them properly, as shown in
diagram 3.
4.1 Connect the spray hose to the click connection of outlet
hose just by a simple push. Attach the weight to the spray
hose at the marked position,as shown in diagram 4.
4.2 Turn on the water valves then t
he faucet.
Run the water flow for 15 seconds to clean up the lines
and check for any leaks.
4.3 Test with the water running, and make certain of the
faucet sprayer changes between stream and spray
properly, as shown in diagram 5.
5. Turn off the faucet. Pull out or pull down the spray head
and get it return for a few times to check the pull-out hose
is functioning properly.
1. Cleaning
Before installation, shut off the water supply valves and clean
up the water supply system.
2. Mounting hole
Make sure the mounting hole size is between 33mm- 35mm
as shown in the diagram.
3. Protection
Clean the area of the mounting holes before installation.
To preserve the delicate finish of the faucet, please
Do not scratch, but use a soft cloth to wipe around
it.
Do not tighten the faucet too hard, so as to avoid deformation
or fracture.
1. Water pressure
Min: 0.05MPa Max:0.75MPa
2. Temperature of water supply≤85
℃
3. Working Temperature≥0℃
1. Take the faucet out of the packing box, and
A. For 1-hole installation, fit the rubber washer over the
hoses into faucet bottom. Then fit the faucet to the hole
on the sink
as shown in diagram 1A.
B. For 3-hole installation, fit the rubber washer over the
hoses into faucet bottom, followed with the deck plate,
aligning the grooves in the deck plate with the arches
on the faucet base, as shown in diagram 1B.
2. Slide the rubber gasket, then the metal gasket, followed
by the mounting nut up and over the hoses onto the faucet
shank, and hand tighten the
m firmly. Fix the 2 screws for
further security
as shown in diagram 2.
Maintenance
1. Operate the faucet gently in order for a sustainable use.
2. Always blot dry any water from faucet surface. Clean it with a
damp non-abrasive cloth and wipe dry with a clean soft towel
should be helpful to maintain good finish of the faucet.
To remove water spots, apply warm water and a damp soft
cloth. Make certain to rinse thoroughly with water imm
ediately
after cleaner.
3. Although the finish is extremely durable, it can be damaged by
some cleaners. Do not use detergent powder, polishing
powder, granular detergent or nylon brush to clean.
4. Do not use acidic detergents. If happened, it must be rinsed
properly and wiped dry with a soft towel.
5. When the air temperature is below 0
℃
, heating solution in the
house is a must.
6.Shu
t off the water supply valves when the faucet will not be
in use for an extended amount of time.
7.We reserve the right to make revisions in the design of faucets
without notice.
handle turning direction
spray
mode
stream
mode
cold supply hose
hot supply hose
Attention
Mounting hole
33 - 35
100
Wall
Sink
4
5
6
3
2
1B
1A
9/16-24UNEF-2B
9/16-24UNEF-2B
rubber
washer
deck
plate
rubber gasket
metal gasket
screw
mounting nut
faucet
shank
rubber
washer
stop
m
o
c
.
s
p
u
o
r
g
e
n
i
f
n
u
r
@
o
f
n
i
:
s
e
c
i
v
r
e
s
d
n
a
s
t
r
a
P
weight
locator mark
Push