Installation manual Dimensions:D26™ H23” L8 Bib Teletype bulb not included Lamp Frame Total Weightless) 185 Thank you fer choosing our product(s). i Company 1s actively involved in every step of the productions Our are designed to be utilized for every application that graces your home or business. Ye pride ourselves in providing the most prompt and courtesy service to all of the valued customers. Please find the enclosed detailed Instruction and read carefully for proper installation.
D26” H23" L8 SAFETY Warning: MAKE SURE THE ELECTRICITY TO THE WIRES YOU ARE WORKING ON IS SHUT OFF.BY EITHER REMOVING THE FUSE OR TURNING OFF THE CIRCUIT BREAKER. CAUTION Before assembling the lighting fixture, please read all instructions carefully. All frame & crystal components are fragile, please handle with care. Required supply circuit : 110 130V/60Hz Labeled wires are “L” for live wire, “N” for neutral wire, “E” for ground wire.
D26” H23” L8 Step 1 Please use the parts list to ensure you are not missing any parts D26” H23” L8 PARTS LIST part picture Description Qty| Check list ZA | 4"Mounting Bracket cover Canopy ring 1 D Ls” Twist design 1 Po ewer cord 12 APT-1-16# rollerblading 1 P1 @ Loop Cover 3 P3 Ao Glass dish 5"Cover 9 P5 Tube 1 15.
D26” H23" L8 D26” H23” L8 part picture Description Qty Check list part picture Description Qty | Check list Al W 8 B é | g Bl g8 +911-63# C & 8 D wesvedDy| 1050-14m74911-634 | 8 E banana | 1050143481911405 5 F poy | 1050-FORETOLD-40 1 G é | 45
" ~N* [ D26” H23” L8 Step 2 Canopy Installation Instruction Tighten the nut up and down: Hot wire Neutral wire Ground wire D26” H23” L8 IMPORTANT :Test sockets with bulb before dressing the fixture. 1 . Attach the crossbar to the electrical box. 2 .Pass the lamp wire and ground wire through the loop, canopy ring and center hole of canopy cover. 3 .Screw's” threaded pipe into the crossbar and fasten with hex-nut. 4 ,Pull wires up through the nipple. 5 .Screw loop only onto threaded pipe. 6 .
D26” H23" L8 Frame Assembly Diagram 00— 02—j= D26” H23” L8 Step 3 Frame Assembly Instructions Installation: Please read all instructions carefully. Before you proceed to install, make sure. that the power supply is turned off and remains off until installation is complete. Please note that each part has been assigned a number. Please proceed in a numerical order. 1.Hang the chain (01) on the ceiling, 2.Fix the lamp arm (10) into the metal base cover (11) pressing holes, screw them with nuts.
D26” H23" L8 D26” H23” L8 Crystal Dressing 1 1 Diagram When dr he channel en dressing the chandelier Step 4 Crystal Dressing Instructions Then dressing tho chandelier her to wear either rubber or cotton Hang crystal "A", "Algal. "B". "B1", "C". "D".
D26” H23" L8 Congratulations ! You are now done installing your fixture. Sit back and admire each crystal as it will become the statement piece for your room/house. If you require any additional assistance, please contact us Thank you. D26” H23” L8 Cleaning and Maintenance of Chandelier Frame The finish on our chandelier frames and fixture frames is protected by a durable coating of lacquer. To clean, use a clean, soft, dry cloth.
D26” H23" L8 Warranty The finish and frame of your new chandelier or fixture are warranted for a period of from the date of purchase.Our company will at its option, repair or replace any frame that has a defect in the material or workmanship during the warranty period.All crystals are guaranteed for their original quality during the life of the chandelier. Breakage is not covered by this warranty.