Wersion 1.
ColorWash 750 AT Tungsten Table of contents 1. Safety instructions.......................................................................................................... 3 2. Operating determinations............................................................................................... 4 3. Description of the device................................................................................................ 5 4. Installation......................................................................
CAUTION! Keep this device away from rain and moisture! Unplug mains lead before opening the housing! FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOU INITIAL START - UP! 1. Safety instructions Every person involved with installation and maintenance of this device have to: - be qualilfied - follow the instructions of this manual CAUTION! Be careful with your operations.
2.Operating determinations This device is a moving-head for creating decorative effects and was designed for indoor use only. If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on immediately. The arising condensation water might damage your device. Leave the device switched off until it has reached room temperature. Never run the device without lamp! Do not shake the device. Avoid brute force when installing or operating the device.
3. Description of the device 1 - Front lens 2 - Pan lock 3 - Base 4 - Handle 5 - Head yoke 6 - Tilt unlock button (green) 7 - Tilt lock button (red) 8 - Moving head The head should be locked for transportation- the tilt lock button (7) is pushed and the pan lock/unlock lever (2) is in locked position. To unlock the head, press the tilt unlock button (6) and move the pan lock/unlock lever (2) into unlocked position.
4. Installation 4.1 Connection to the mains For protection from electric shock,the fixture must be earthed! The ColorWash 750E AT Tungsten is equipped with auto-switching power supply that automatically adjusts to any 50/60Hz AC power source from 110-240 Volts. For use with 100-130 V supplies,the both main 6.3 A fuses has to be exchanged for 10 A fuses which are enclosed in the packing. To install the 10 A fuses: 1. Disconect the fixture from AC power. 2.
5. Reinsert the lamp cover (2) and tighten two quarter-turn fasteners (1) again. 6. Align the new lamp (see instructions below) 7. Reset „Lamp On Time” and „Lamp Strikes” counters in „Fixture information” menu. Do not operate this fixture with open lamp cover! 4.3 Lamp adjustment The lamp holder is aligned at the factory. Due to differences between lamps, fine adjustment may improve light performance: 1. Switch on the fixture and after reset turn on the lamp. 2.
4.5 Installing top hats The ColorWash 750E AT Tungsten can be fitted with various types of the top hats-see chapter "Technical specifications".If you wish to install a top hat (optional),follow the instructions: Switch the device off before installing the top hat! Installing the top hat on the front lens-holder of the fixture: 1.Put desired top hat onto a front lens-holder and fasten it by two fastening screws. 2.
4.6 Rigging the fixture DANGER TO LIFE! Please consider the respective national norms during the installation! The installation must only be carried out by an authorized dealer! The installation of the projector has to be built and constructed in a way that it can hold 10 times the weight for 1 hour without any harming deformation. The installation must always be secured with a secondary safety attachment, e.g. an appropriate catch net.
For overhead use, always install a safety-rope that can hold at least 10 times the weight of the fixture. You must only use safety-ropes with screw-on carabines. Pull the safety-rope through the two apertures on the bottom of the base and over the trussing system etc. Insert the end in the carabine and tighten the fixation screw. Fixation via the omega holders 1.Bolt each clamp (1) to the omega holder (4) with M12 bolt and lock nut through the hole in the holder. 2.
4.7 DMX-512 connection The fixture is equipped with both 3-pin and 5-pin XLR sockets for DMX input and output.The sockets are wired in parallel. Only use a shielded twisted-pair cable designed for RS-485 and 3-pin or 5-pin XLR-plugs and connectors in order to connect the controller with the fixture or one fixture with another.
4.8 Ethernet connection The fixtures on a data link are connected to the Ethernet with Art-Net communication protocol.The controlling software from PC (or lighting console) has to support Art-Net protocol. Art-Net communication protocol is a 10 Base T Ethernet protocol based on the TCP/IP.Its purpose is to allow transfer of large amounts of DMX 512 data over a wide area using standard network technology. IP address is the Internet protocol address.The IP uniquely identifies any node (fixture) on a network.
Ethernet / DMX operation Options “Ethernet/DMX” has to be selected from “Set Ethernet Mode” menu on the first fixture (connected to the network) in the fixture chain,next fixtures have standard DMX addresses. Connect the Ethernet-input of the first fixture in the data chain with the network. Connect the DMX output of this fixture with the input of the next fixture until all fixtures are connected to the DMX chain. Caution: At the last fixture, the DMX chain has to be terminated with a terminator.
5. ColorWash 750 AT Tungsten - DMX Protocol-version 1.4 Mode/Channel Value Function Type of control 1 2 3 4 5 1 1 1 1 14 0 - 255 Pan Pan movement by 530° proportional 2 2 2 2 15 0 - 255 Pan Fine Fine control of pan movement proportional 3 3 3 3 16 0 - 255 Tilt Tilt movement by 280° proportional 4 4 4 4 17 0 - 255 Tilt fine Fine control of tilt movement proportional 0 5 5 5 5 18 1 - 255 1 - 255 - - 6 - - 6 7 8 6 7 8 20 - - P./T.
Mode/Channel 1 2 3 4 5 7 7 9 9 6 8 8 10 10 8 9 9 11 11 10 10 10 12 12 - 11 12 13 14 11 12 13 14 13 14 15 16 13 14 15 16 19 - - - Value Function Type of control 0-255 Cyan Cyan (0-white, 255-full cyan) proportional 0-255 Magenta Magenta (0-white, 255-full magenta) proportional 0 - 255 Yellow Yellow (0-white, 255-full yellow) proportional 0 - 255 Colour temperature correction filter (0-3300 K, 255-8000 K) proportional 0 - 255 Speed of CMY and conv.
Mode/Channel 1 2 3 4 5 15 - 17 - - 16 17 15 18 17 - 19 - 12 13 18 16 20 18 1 19 17 21 19 4 20 21 - 22 - 18 23 20 5 2 Value Function Type of control 0-255 Beam shaper fine indexing (set position on channel 14 (16) Fine indexing proportiona 0 - 255 Zoom Coarse zoom from min. to max.
6. Controller mode The fixtures are individually addressed on a data link and connected to the controller.The fixtures respond to the DMX signal from the controller. 6.1 DMX addressing The control panel on the front panel of the fixture allows you to assign the DMX fixture address, which is defined as the first channel from which the ColorWash 750E AT Tungsten will respond to the controller.
7.
Personality User Mode User A Settings User B Settings User C Settings DMX Presetting Mode 1 Ch.1 Pan : Ch.21 El. Dimmer Set Active Mode 2 Ch.1 Pan : Ch.18 El. Dimmer Set Active Mode 3 Ch.1 Pan : Ch.23 El. Dimmer Set Active Mode 4 Ch.1 Pan : Ch.20 El. Dimmer Set Active Mode 5 Ch.1 Shutter/Strobe : Ch.
Test sequences Mode 1 Mode 2 Pan (0-255) Tilt (0-255) Zoom (0-255) Run Test Program Manual Mode Preset Effect Control Pan (Position 1,...,Position 7) : El. Dimmer (Position 1,...
Effect Adjustment DMX Values Calibrate Values Pan (0-255) : El.Dimmer (0-255) Cyan (0-225) : Mech.
8. Control menu The control panel situated on the front panel of the base offers several features. You can simply set the DMX address, read the number of the lamp or unit hours, switch On and Off the lamp, run test, make a reset and also use many functions for setting fixture behaviour. Control elements on the control board: [RNS] encoder wheel-moves between menu items on the the same level, scrolls between values.
Total Hours - The function shows the total number of the operation hours with the lamp on since the ColorWash 750E AT Tungsten has been fabricated. Resetable Hours - The function shows the number of the operation hours with the lamp on that the ColorWash 750E AT Tungsten has been powered on since the counter was last reset. In order to reset this counter to 0, press [ENTER] twice. Lamp On/Off Cycles - Select this submenu to read the total number of the "Lamp On/Off" cycles.
IC1 DS--- Display processor 1 on the display module in the fixture base IC2 DS--- Display processor 2 on the display module in the fixture base 8.3 Personality Use this menu to to modify ColorWash 750E AT Tungsten operating behavior. User mode --- ColorWash 750E AT Tungsten allows you to recall up to 3 user settings.After switching the fixture on for the first time, the User A settings is active.
Pan/Tilt Moving --- This function closes the light output during changing pan/tilt positions. Dimmer Curve - Select desired dimmer running. Curve 1 Curve 2 IR Sensor --- Select this function to switch on/off infra-red remote control. Init Effect Positions --- Select this function to set all effects to the desired positions.After switching the fixture on (if DMX is not connected),all effects will move to these init positions.
Select the program you wish and press [ENTER].The selected program starts running.By Pressing [ENTER] again is possible to pause the program running. Editing Program --- Select this menu to edit or create the program.The ColorWash 750E AT Tungsten has one built-in program and the 3 free programs,each up to 99 steps.Each program step has a step time. Step time-the time,during which effects last in the current step. Procedure: 1.
Yellow channel 24 channel 21 channel 26 channel 23 channel 23 Conversion filter channel 25 channel 22 channel 27 channel 24 channel 24 Effect wheel channel 26 channel 23 channel 28 channel 25 channel 25 Effect indexing channel 27 channel 24 channel 29 channel 26 channel 26 Zoom channel 28 channel 25 channel 30 channel 27 channel 27 Mech. dimmer 1 channel 29 channel 26 channel 31 channel 28 channel 28 Mech.
switching the fixture off ,but if you want to go directly to “normal operation mode”,execute any fixture reset. Note:All motors (except pan and tilt motors) in “Power down mode” are deactivated and switching the lamp on from the control panel is blocked. 10. RDM This fixture is ready for RDM operation.RDM (Remote Device Management) is a bi-directional communications protocol for use in DMX512 control systems, it is the new open standard for DMX512 device configuration and status monitoring.
11. Error and information messages Occured errors during fixture operation are signaled by warning icon on the display: Press [ESC] to see the current error messages. Description of error messages: Overheated-Lamp Off This message informs that the fixture head had been overheated and the lamp was switched off by head temperature sensor. Overheated-Lamp Low This message informs that the fixture head has been overheated and the lamp power is reduced.
The messsages will appear after the reset of the cyan flag if the flag is not located in the default position. Magenta Lamella Error 1 (Magenta Lamella Error 2 ) The messsages will appear after the reset of the magenta flags if the flag is not located in the default position. Yellow Lamella Error 1 (Yelow Lamella Error 2 ) The messsages will appear after the reset of the yellow flags if the flag is not located in the default position.
CMY colour mixing module - Smooth CMY colour mixing system - Colour temperature correction filter increases the colour temperature from 3300 K to 8000K - 30 CMY macros Strobe: - Strobe effect with variable speed (max.15 flashes/sec.),random and variable pulse effects.
Dimensions(mm) - Dimensions of the fixture: - Dimensions of the optional top hats: Accessories - Omega holder (2 pieces)................................No.99010420 Optional Accessories - Module of front wide-angle lens ......................No. 99010879 - Flash cable RS232/DMX..................................No.13050624 - Top hat standard 45 ........................................No.10980044 - Top hat long 70 ................................................No.
13. Maintenance and cleaning It is absolutely essential that the fixture is kept clean and that dust, dirt and smoke-fluid residues must not build up on or within the fixture. Otherwise, the fixture‘s light-output will be significantly reduced. Regular cleaning will not only ensure the maximum light-output, but will also allow the fixture to function reliably throughout its life.
air filter cover quarter-turn fasteners Replacing the fuse Before replacing the fuse, unplug mains lead. Procedure: 1) Unscrew the fuseholder on the rear panel of the base with a fitting screwdriver from the housing (anticlockwise). 2) Remove the old fuse from the fuseholder. 3) Install the new fuse in the fuseholder. 4) Replace the fuseholder in the housing and fix it. Specifications are subject to change without notice.
