DJ SCAN 250 XT Table of contents 1. Safety instructions ......................................................................................................... 3 2. Operating determinations ............................................................................................. 4 3. Description of the device .............................................................................................. 5 4. Installation ..................................................................................
CAUTION! Keep this device away from rain and moisture! Unplug mains lead before opening the housing! FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOU INITIAL START - UP! 1. Safety instructions Every person involved with installation and maintenance of this device have to: - be qualilfied - follow the instructions of this manual CAUTION! Be careful with your operations.
2. Operating determinations This device was designed for indoor use only. If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on immediately. The arising condensation water might damage your device. Leave the device switched off until it has reached room temperature. When taking the device into operation, please make sure that the housing is closed firmly with all the necessary screws tightened up.
3.
4. Installation 4.1Fitting/Exchanging the lamp DANGER ! Install the lamps with the device switched off only. Unplug from mains before ! Screw "A" Screw "B" To insert the lamp (MSD 250 or MSD 250/2) open the small cover at the rear panel (see the drawing) by loosening the 2 Phillips screws "A" and "B" on the cover. Gently pull out the lamp assembly. If changing the lamp, remove the old lamp from the socket. Insert the lamp to the socket.
Lamp adjustment The lampholder is aligned at the factory. Due to differences between lamps, fine adjustment may improve light performance. Strike the lamp and focus the light on a flat surface (wall). Center the hot-spot (the brightest part of the beam) using the 3 adjustment screws "X, Y, Z". Turn one screw at a time to drag the hot-spot diagonally across the projected image. If you cannot detect a hot-spot, adjust the lamp until the light is even.
4.3 Rigging the fixture The installation of the projector has to be built and constructed in a way that it can hold 10 times the weight for 1 hour without any harming deformation. The installation must always be secured with a secondary safety attachment, e.g. an appropriate catch net. This secondary safety attachment must be constructed in a way that no part of the installation can fall down if the main attachment fails.
4.5 DMX-512 connection/connection between fixtures The wires must not come into contact with each other, otherwise the fixtures will not work at all, or will not work properly. Only use a stereo shielded cable and 3-pin XLR-plugs and connectors in order to connect the controller with the fixture or one fixture with another.
5.
6. Addressing The control board on the top side of the DJ SCAN 250 XTallows you to assign the DMX fixture address, which is defined as the first channel from which the DJ SCAN 250 XTwill respond to the controller. If you set, for example, the address to channel 5, the DJ SCAN 250 XTwill use the channel 5 to 10 for control. Please, be sure that you don’t have any overlapping channels in order to control each DJ SCAN 250 XTcorrectly and independently from any other fixture on the DMX data link.
Tilt reverse This function allows you to invert the tilt movement. Use the [ Up ] and [ Down ] keys to select "On" if you wish this feature or "Off" if you don’t wish this feature and press [ Menu ] to confirm and return to the main menu. Test program This function allows you to run a special test program without an external controller, which show you some possibilities of using DJ SCAN 250. Press the [ Menu ] key to run the test program, the "tSt" will start to flash.
Colours: - 11 dichroic-filters plus white - UV-filter - 3 dichroic semicolours filters - Colour-wheel with variable rotation speed Rotating gobos: - 9 metal gobos plus open - Gobo rotation - The gobos have an outside diameter of 16 mm ,thickness 0.5 mm,aluminiumand, an image diameter of 13 mm.
9. Maintenance and cleaning The operator has to make sure that safety-relating and machine-technical installations are inspected by an expert after every four years in the course of an acceptance test. The operator has to make sure that safety-relating and machine-technical installations are inspected by a skilled person once a year.
10.Appendix- Changing the power supply settings Both the transformer and the ballast must be connected correctly for the local AC voltage and frequency. The wrong settings can cause poor performance or demage of the moving head.The factory settings are printed next to the power cord. If you want to change the power supply settings,follow the instructions: Fastening screws Control board cover Front cover Fastening screws UE version: 1.Disconnect the fixture from AC power. 2.
230V/60Hz version: 1.Disconnect the fixture from AC power. 2.Remove the control board cover by loosening the 4 screws. 3.Move the wire 1 on the transformer connection block to the position according to the desired voltage. 4.Remove the front cover by loosening the 4 screws. 5.Move the wire 2 on the ballast connection block to the position according to the desired frequency (voltage). Example: Transformer Ballast 4.Put the covers back before applying AC power. US version: 1.