ASSEMBLY INSTRUCTIONS INSTRUCCIONES DE ENSAMBLAJE INSTRUCTIONS D’ASSEMBLAGE RiverRidge® Ashland Wall Cabinet with Mirror, Open Shelf Gabinete de pared con espejo y repisa abierta Ashland RiverRidge® Armoire murale avec miroir et étagère ouverte Ashland RiverRidge® 06-170 - White, Blanco, Blanc RiverRidge® is a registered trademark of Sourcing Solutions, Inc., Hudson, WI 54016, USA RiverRidge® es una marca comercial registrada de Sourcing Solutions, Inc.
WARNING ADULT ASSEMBLY REQUIRED: This product requires assembly by an adult because of small parts. Care should be taken in unpacking and assembling this item to keep small parts away from children. During assembly children should be kept away from the product due to possible risk of injury. SERIOUS OR FATAL INJURIES CAN OCCUR FROM FURNITURE TIP-OVER. IN ORDER TO PREVENT OVERTURNING, THIS PRODUCT MUST BE USED WITH THE TIPOVER RESTRAINTS OR WALL MOUNTING HARDWARE PROVIDED. PLEASE READ WARNINGS BELOW.
ADVERTENCIA REQUIERE QUE UN ADULTO REALICE EL ENSAMBLAJE: Este producto requiere que un adulto lleve a cabo el ensamblaje debido a las piezas pequeñas. Debe tener cuidado al desempacar y ensamblar este artículo para mantener las piezas pequeñas alejadas de los niños. Los niños deben mantenerse alejados del producto durante el ensamblaje debido al posible riesgo de lesiones. LA CAÍDA DE LOS MUEBLES PUEDE OCASIONAR LESIONES GRAVES O FATALES.
AVERTISSEMENT L’ASSEMBLAGE DOIT ÊTRE EFFECTUÉ PAR UN ADULTE : Ce produit doit être assemblé par un adulte à cause de la présence de petites pièces. Lorsque vous déballez et assemblez cet article, veillez à tenir les petites pièces hors de portée des enfants. Les enfants doivent être tenus à l’écart du produit en raison du risque de blessure pendant l’assemblage. LE BASCULEMENT D’UN MEUBLE PEUT CAUSER DES BLESSURES GRAVES VOIRE MORTELLES.
PARTS LIST 1 8 4 3 9 5 2 6 7 NO QTY DESCRIPTION 2 1PC Left Side Panel 3 1PC Right Side Panel 4 1PC Cross Bar 5 1PC Adjustable Shelf 6 1PC Shelf 7 1PC Bottom Board 8 1PC Back Board 9 1PC Door 1 1PC Top Board
PARTS LIST NO A PARTS QTY DESCRIPTION 8PCS Cam Bolt B 8PCS Cam Lock C 6PCS Wood Dowel D 2PCS Hinge E 12PCS Screw (4x12mm) F 1PC Knob G 1PC Machine Screw (4x18mm) H 14PCS Screw (2.
STEP 1 A A A 3 2 1. 2. A Screw 2 cam bolts (A) into cam bolt holes on left side panel (2). Screw 2 cam bolts (A) into cam bolt holes on right side panel (3). STEP 2 a b c C 4 C C 2 1. 2. 3. 3 C B B 6 B B Insert 4 wood dowels (C) into wood dowel holes on left side panel (2) and right side panel (3).
STEP 3 3 2 C C I I 7 I I 1. 2. 3. Insert 2 wood dowels (C) into wood dowel holes on left side panel (2) and right side panel (3). Attach bottom board (7) to left side panel (2) and right side panel (3) by inserting wood dowels (C) into wood dowel holes on bottom board (7). Insert 4 screws (I) through holes on bottom board (7), then tighten to left side panel (2) and right side panel (3). STEP 4 A A A 1 1. Screw 4 cam bolts (A) into cam bolt holes on top board (1).
STEP 5 1 3 B B B B 2 1. 2. Attach top board (1) to left side panel (2) and right side panel (3) by inserting cam bolts (A) into cam lock holes on left side panel (2) and right side panel (3). Insert 4 cam locks (B) into cam lock holes on left side panel (2) and right side panel (3), then rotate clockwise to secure cam bolts (A) in place. STEP 6 H H H H H H H H 3 1.
STEP 7 1 3 2 1. 2. K K K 5 K Insert 4 shelf holders (K) into holes on left side panel (2) and right side panel (3). Make sure 4 shelf holders (K) are at same level. Place adjustable shelf (5) onto shelf holders (K). STEP 8 E E D E E D 9 G F 1. 2. Attach 2 hinges (D) to door (9) by inserting 4 screws (E) through holes on hinges (D), then tighten to door (9). Attach knob (F) to door (9) by inserting 1 machine screw (G) through hole on door (9), then tighten to knob (F).
STEP 9 1 E 9 E 3 2 a b 1. 2. c d Attach door (9) to right side panel (3) by inserting 8 screws (E) through holes on hinges (D), then tighten to right side panel (3). To adjust hinges, tighten screws shown in image “a” to adjust door up or down, tighten screw shown in image “b” to adjust door to or from cabinet and tighten screw shown in image “c” to adjust door side to side.
STEP 10 L L L 4 J J OPTION #1 OPTION #2 DRYWALL J WALL ANCHOR WITH SCREW J L J DRYWALL WOOD STUD SCREW ONLY Option #1: Securing to Drywall 1. Using wall mounting paper template to determine position, screw 2 plastic anchors (L) into drywall. 2. Insert 2 screws (J) through holes on cross bar (4) and into plastic anchors (L) and tighten. Option #2: Securing to Drywall and Wood Stud 1. Insert 2 screws (J) through holes on cross bar (4), then tighten through drywall and into wood stud.
LISTA DE PIEZAS N.° DESCRIPCIÓN CANT.
PASO 1 1. Atornille 2 pernos de anclaje (A) en los agujeros correspondientes del panel izquierdo (2). 2. Atornille 2 pernos de anclaje (A) en los agujeros correspondientes del panel derecho (3). PASO 2 1. Inserte 4 pasadores de madera (C) en los agujeros correspondientes del panel izquierdo (2) y el panel derecho (3). 2.
PASO 10 Opción n.º 1: fijar a una pared de yeso 1. Atornille 2 anclajes plásticos (L) a la pared de yeso usando una plantilla de papel para ensamblaje en pared a fin de determinar la posición. 2. Inserte 2 tornillos (J) a través de los agujeros de la barra transversal (4) y en los anclajes plásticos (L), luego, ajústelos. Opción n.º 2: fijar a una pared de yeso y a un montante de madera 1.
LISTE DES PIÈCES N.° DESCRIPCIÓN CANT.
ÉTAPE 1 1. Vissez 2 boulons à came (A) dans les trous du panneau latéral gauche (2) prévus à cet effet. 2. Vissez 2 boulons à came (A) dans les trous du panneau latéral droit (3) prévus à cet effet. ÉTAPE 2 1. Insérez 4 goujons en bois (C) dans les trous du panneau latéral gauche (2) et du panneau latéral droit (3) prévus à cet effet. 2.
ÉTAPE 10 Option 1 : Fixation sur des cloisons sèches 1. En utilisant un gabarit de papier de montage mural pour déterminer la position, vissez 2 ancrages en plastique (L) dans la cloison sèche. 2. Insérez 2 vis (J) dans les trous de la barre transversale (4) et dans les ancrages en plastique (L) et vissez-les. Option 2 : Fixation sur des cloisons sèches et des montants en bois 1.