User Manual

ManualsBrandsRhino Shelter ManualsCarEXT ROUND-12WX24LX8H

Table Of Contents

Assembly Instructions Extended Round Style 12 x 24 x 8

V2.2

Please Do NOT Return Assembly to Dealer or Store. For All questions or Shortages please call MDM Products directly

Customer Service 800-447-7079 or 203-877-7070

ASSEMBLY INSTRUCTIONS

ROUND STYLE 12Wx24Lx8H

Congratulations!

Congratulations on your purchase of a Round Extended

Style Garage/Shelter by MDM Products LLC. With

proper installation, use, and maintenance, your new unit

will provide many years of good and suitable service.

Your new Rhino Shelter portable enclosure is a

combination of excellent engineering and well thought

out design. The unit is comprised of a rigid tubular

frame, covered with a long life polyethylene cover and

double door ends.

The multiple part frame is pre-drilled for easy insertion of

hardware to assemble. The tubing is made from high-

grade galvanized steel tubing, to resist moisture and

oxidation over the life of the shelter. The covering

membrane is made from ASTM-5 approved polyethylene

materials. The cover is UV protected for continual

exposure to the sunlight.

It is suggested that you read the assembly instructions

completely

before you begin. This will help attain the

best results for your installation the first time.

SAFETY & CODE WARNING

The installation of this unit must conform to the

requirements of all authorities having jurisdiction in

your specific local area. In the absence of such

requirements, the installation must conform to the

provided assembly and installation instructions.

MDM Products LLC will not be responsible for failure

to comply with any requirements in a given local

area. Consequential damages or injuries caused by

improper installation, alteration, or improper use are

strictly that of the user. Unit MUST be cleared of All

Snow Accumulation immediately to avoid overload.

Unit is not to be used for occupancy for any length

of time. No running internal combustion engines,

open flames, or contact with heated surfaces are

allowed.

For installation assistance or Customer Service, please

call 800-447-7079 or 203-877-7070, 8AM-5PM EST.

Cartons should be inspected upon delivery from carrier,

and any evident damages should be noted on the bill of

lading before signing. If upon opening the cartons

hidden damage is noted, contact carrier or its agent

immediately. Claims for shipping damage MUST be

made with the shipping company. An inspection of the

goods will most likely be required. Do not discard

packing or any components before the freight company’s

inspection. All claims for freight damage must be made

with 15 days of receipt of the goods in accordance with

ICC regulations.

ASSEMBLY PROCEDURE

The proper sequence and steps to install this unit will

produce a proper and good installation. Failure to read

and follow these guidelines may result in an improper

installation and will void all warranty and protection the

owner is entitled to with the product. The steps to be

undertaken are:

1. Perform an inventory check before beginning to be

certain all components are available for installation.

2. Prepare location and place both unit boxes near

location sight.

3. Assemble seven (7) frame arches of unit

4. Assemble unit end arch, first interior arch, and Wind

Braces with first base rails and side rail sections.

5. Add additional arch assemblies with each section of

base rails and side rails.

6. Place frame into desired position and level

frame

both end-to-end and side-to-side. Measure interior

of frame feet across opposite corners and square

7. Anchor frame assembly to ground with provided

anchors, u-bolts and drive rod provided.

8. Install two(2) doors on both ends of frame assembly.

9. Install main cover over frame assembly.

TOOLS REQUIRED

The following hand tools will be needed for proper

installation of your new Rhino Shelter unit:

9/16” Open End Wrench

9/16” Socket or Box Wrench

Large Flat Tip Screwdriver

Maul or Sledgehammer

2 foot Level

6-Foot Step Ladder

INVENTORY CHECK

Start installation procedure by removing all components

from packaging and ensure all components are present

Qty No. Part Number Description

1 RUC-10000 Main Unit Cover –

122408RSK

2 DZD-5002 End Panel Door with

Double Zippers

4 1 EUL-4021 End Upright w/Foot

7 2 RC-3020 Right Side Crest Tube

7 3 LC-3021 Left Side Crest Tube –

swedged end

Summary of content (9 pages)

PAGE 1
Assembly Instructions Extended Round Style 12 x 24 x 8 ASSEMBLY INSTRUCTIONS ROUND STYLE 12Wx24Lx8H inspection. All claims for freight damage must be made with 15 days of receipt of the goods in accordance with ICC regulations. Congratulations! ASSEMBLY PROCEDURE Congratulations on your purchase of a Round Extended Style Garage/Shelter by MDM Products LLC. With proper installation, use, and maintenance, your new unit will provide many years of good and suitable service.
PAGE 2
Assembly Instructions Extended Round Style 12 x 24 x 8 10 2 25 4 5 6 CSU-4020 CW-1800 SCR-2030 5 7 ECR-2031 8 35 2 37 37 2 8 6 6 1 4 10 TB-3004 CBN-3005-3 CBN-3005-2 CBN-3005-N CBN-3005-W R-3003 BC-36 DBA-3000 UB-3002 DR-3001 EP-1000 EP-1001 Center Straight Uprights Corner Wind Brace Swedged Cross Ridge Poles End Cross Poles – plain ends Turnbuckles Carriage Bolts – 3¼” Carriage Bolts – 2-1/8“ 3/8” Nuts Washers – 3/8” Cupped 3/16” Rope Bungee Cord Hold Ups Earth Cable Anchors U Bolts with Nuts 36” D
PAGE 3
Assembly Instructions Extended Round Style 12 x 24 x 8 RC-3020 Right Crest Tube SITE PREPARATION Select a level or as close to level as practical location for your Rhino Shelter unit. The unit should be placed on a base of materials suitable for the storage load to be protected. The unit should not be located under trees, which will shed hard fruit such as apples, walnuts, or heavy pine cones.
PAGE 4
Assembly Instructions Extended Round Style 12 x 24 x 8 Top Ridge Under End Arches Top Ridge Over Interior Arches Swedged Cross Rail should fasten under the End Top Crest Arch at the End arch. NOTE: Do not completely tighten bolts that connect the Cross Rails to the End Arches. They must be removed for proper for End Panel Zippered Door installation Under End Arch End Arch Assembly Side Cross & Base Cross Poles Inside Unit Interior Arch Assembly Over Interior Arch Step 7.
PAGE 5
Assembly Instructions Extended Round Style 12 x 24 x 8 Align each Arch with string to make edge of Frame STRAIGHT before securing Step 8. Once frame is square and properly supported, tighten carriage bolts on all frame members, except for End Arch members to Cross Rails along base, side, and top. Support End Arch feet with patio blocks or bricks as needed if ground is soft and will not support weight.
PAGE 6
Assembly Instructions Extended Round Style 12 x 24 x 8 ANCHOR STEP 2 Place the Drive Rod through the loop in the anchor lanyard. Pull upward to set anchor head into the ground. END PANEL INSTALLATION Note: End panels MUST be installed before installing Main Cover onto frame. Step1. Remove Carriage bolts from the Top Crest Rail and the two Upper Cross Rails. Install one End Panel Door w/Zippers DZD-5002 at a time to the Frame assembly. Carefully align the door material over the arch to make an even fit.
PAGE 7
Assembly Instructions Extended Round Style 12 x 24 x 8 Re-adjust gathered material evenly along inside edge of door rope slot. This step is key to getting a good door fit. Tie off the end off the rope to a second turnbuckle (fully opened) attached to a hole in the foot of the end arch on the opposite side. The end panel can then be tightened further by adjusting each turnbuckle. The rope slot should be located inside the unit, with the frame members passing through the pre-cut slots in the end panel/door.
PAGE 8
Assembly Instructions Extended Round Style 12 x 24 x 8 Temporarily tie the other end of the rope to the turnbuckle. Go over the entire edge of the cover and adjust the excess folds of material around the end so it is evenly distributed around rope slot. Once the rope is pulled tight and the cover is adjusted evenly over frame, tie off the rope end to the turnbuckle. All slack should be out of the rope at this time. Tighten the turnbuckle to further tighten the cover if necessary.
PAGE 9
Assembly Instructions Extended Round Style 12 x 24 x 8 DOOR HOLD UPS All Rhino Shelter doors are manufactured with a pocket on the bottom edge along the width axis. A ½” - 1” plastic or metal tube can be inserted into the pocket and trimmed to fit door width. Weight will reduce door movement in wind. Four (4) bungee straps are provided to retain the door in the up position. Roll the door from the bottom and secure the door roll with a bungee through the upper door grommet as shown.