User manual

ManualsBrandsRGBlink ManualsMusical equipmentVSP 5360

VSP 5360 Quick Start

Version 1.1

Page 1 of 4

VSP 5360 – Quick Start

Installation and Cabling

Back Panel

Interfaces

RS232 Interface

DVI input

DVI input port of sending card

Step 1-Mounting

Step 3-SDI Input

Address：S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen,Fujian Province, P.R.C

Tel: 00865925771197 Fax:00865925771202

Email: rgblinkcs@gmail.com http://www.rgblink.cn

USB Interface

Power supply port of sending card

Dial Switch Displayport input

SDI input

Step 2-CVBS Input

NOTE

This quick start provides basic instructions for an experienced installer

to set up and operate VSP 5360.

Step 5-VGA Input

Step 6-Displayport Input

Step 4-DVI Input

10/100M Interface RJ45

Step 7-SDI Loop Out

USB control port of sending card

Program output

SDI loop out

Preview output

Switch

Step 10-USB Connector

CVBS input BNC port

Power IEC-3

port

16 17

Step 8-Preview VGA Output

Connect display projectors and other

equipment with standard VGA

interface.

Step 9-Program DVI Output

Step 11-LAN (Ethernet) Port

VIEWSIZE THE WORLD

For full installation, configuration, and operation details, please refer to

VSP 5360 user manual, which is available at www.rgblink.com.

Use CAT5 crosswire as the picture shows. The default

IP address is 192.168.0.100. User can change the IP

address via RS232 or USB port.

CAT5 crosswire is one end in T568A standard, the

other in T568B standard.

LAN (Ethernet) port is not standard configuration

module.

Connect VSP 5360 to PC via USB cable for

windows control.

Turn off all equipment power sources.

Input video signals from HD player or HD

camera a n d so on , support 3G/HD/SD-

SDI.

Input signals from DVI signal generator

or computer with DVI port.

Input signal from VGA signal generator,

such as PC or laptop.

Input the video signal from HD player,

computer.

Can connect the next level VSP 5360 or

the device with SDI input.

Connect NTSC, PAL or SECAM component

video to these female BNC connectors.

DVI output is used to connect DVI

display and LED control system, etc.

6 10 11

VGA input

Mega Systems Inc., US Distributor of RGBLink

www.megasystemsinc.com • info@megasystemsinc.com

Toll Free: 866-460-MEGA • Local: 210-684-2600

5718 Kenwick St., San Antonio, TX 78238

Summary of content (4 pages)

PAGE 1
VIEWSIZE THE WORLD VSP 5360 – Quick Start NOTE For full installation, configuration, and operation details, please refer to VSP 5360 user manual, which is available at www.rgblink.com. This quick start provides basic instructions for an experienced installer to set up and operate VSP 5360.
PAGE 2
End terminal How to Add or Clear the Layer Definition of crosswire Pin T568A cable end color T568B cable end color 1 2 3 4 5 6 7 8 White-green Green White-green Blue White-blue White-orange White-brown Brown White-orange Orange White-green Blue White-blue green White-brown Brown T568A CAT5 crosswire is one end in T568A standard, the other in T568B standard.
PAGE 3
How to Crop the Image How to Save the Parameter 1. Push [Crop/Zoom] button, the button lights, user can Push SAVE button, the key lights, OLED shows crop the image. related save information, operate according to the 2. Rotate the knob to crop H LEFT, V UP, H RIGHT, V prompt information. DOWN of the image according to user’s need. Some of the number buttons 0-12 in PRE area are on, 3. If quality image distorts by mistake in improper and some flash.
PAGE 4
Sending card does not support the bottom half part: TS 802 can control the max horizontal resolution 2048, and vertical resolution 640. Each CAT5 output is 320 pixels. All buttons light on together Check if the dial switch is normal; Power off the device, check if two red dial switches on back left part of the device are all upwards, if no, place them upwards, then power on the device again. The red dial switches are mainly for upgrade. Mega Systems Inc.