User's Manual

ManualsBrandsResMed ManualsDehumidifiersS9

Global leaders in sleep and respiratory medicine www.resmed.com

S9 Escape

™

POSITIVE AIRWAY PRESSURE DEVICE

Welcome Guide

English

368870/1 2012-10

S9 Escape

WELCOME

EUR 1/3

Manufacturer: ResMed Ltd 1 Elizabeth Macarthur Drive Bella Vista NSW 2153 Australia. Distributed by: ResMed Corp 9001 Spectrum Center

Boulevard San Diego CA 92123 USA.

ResMed (UK) Ltd 96 Milton Park Abingdon Oxfordshire OX14 4RY UK. See www.resmed.com for

other ResMed locations worldwide.

For patent information, see www.resmed.com/ip.

S9, S9 Escape, H5i, SlimLine and ClimateLine are trademarks of ResMed Ltd and S9, H5i, SlimLine and ClimateLine are registered in U.S.

Patent and Trademark Ofce.

Summary of content (11 pages)

PAGE 1
368870/1 2012-10 S9 Escape S9 Escape™ WELCOME EUR 1/3 POSITIVE AIRWAY PRESSURE DEVICE Manufacturer: ResMed Ltd 1 Elizabeth Macarthur Drive Bella Vista NSW 2153 Australia. Distributed by: ResMed Corp 9001 Spectrum Center Boulevard San Diego CA 92123 USA. ResMed (UK) Ltd 96 Milton Park Abingdon Oxfordshire OX14 4RY UK. See www.resmed.com for other ResMed locations worldwide. For patent information, see www.resmed.com/ip.
PAGE 2
PAGE 3
Welcome Thank you for choosing the S9 Escape. Before operating this device, please read the entire Welcome and Information Guides. DC power inlet Module/Adapter port Air filter S9 at a glance Air outlet SD card slot The S9 system comprises the following elements: • S9 device • SlimLine air tubing • 90W or 30W power supply unit • S9 travel bag • SD card • S9 SD card protective folder.
PAGE 4
3 2 5 4 1 Setup 1. Connect the DC plug of the power supply unit to the rear of the S9. 2. Connect the power cord to the power supply unit. 3. Plug the other end of the power cord into the power outlet. 4. Connect one end of the air tubing firmly onto the air outlet. 5. Connect the assembled mask system to the free end of the air tubing. Notes: •• For more information on assembling your mask see your mask user guide. •• Recommended masks are available on www.resmed.
PAGE 5
S9 basics Start/Stop button Starts or stops treatment. LCD screen Home menu Key: Home Humidity level Setup menu* Allows you to make changes to settings. Info menu* Allows you to view your sleep statistics. *The Info and Setup menus are disabled if S9 Essentials has been enabled by your clinician. Ramp Heated tube Climate Control Start/Stop Push dial Turning the dial allows you to scroll through the menu and change settings. Pushing the dial allows you to enter into a menu and confirm your choice.
PAGE 6
S9 Essentials S9 Essentials is designed to make device interaction and menu navigation easier for you. If enabled by the clinician, S9 Essentials disables the Info and Setup functionality so that you can simply start and stop therapy and adjust ramp, humidification and Climate Control. Navigating the menus In general, to navigate the menus: until the 1. Turn parameter you require is displayed in blue. 4 . 2. Press The selection is highlighted in orange. to until you 4. Press 3.
PAGE 7
Getting started Make sure the power is connected. Adjust the ramp time if required. Fit your mask as described in your mask user guide. . To start therapy press Lie down and arrange the air tubing so that it is free to move if you turn in your sleep. . 6. To stop treatment at any time press 1. 2. 3. 4. 5. Notes: •• Once therapy has started a treatment screen is displayed. •• If power is interrupted during treatment, the device automatically restarts therapy when power is restored.
PAGE 8
Cleaning and maintenance Refer to your mask and humidifier user guides for detailed instructions regarding the care of this device. Daily Remove the air tubing by pulling on the finger grips on the cuff. Hang it in a clean, dry place until next use. Notes: •• Do not hang the air tubing in direct sunlight as it may harden over time and eventually crack. •• Do not wash the air tubing in a washing machine or dishwasher. Weekly 1. 2. 3. 4. Remove the air tubing from the S9 device and the mask.
PAGE 9
SD card An SD card has been supplied to gather therapy data from your S9 device and provide settings updates from your clinician. When instructed to do so, disconnect the S9 device from the power outlet, remove your SD card, insert it in the protective folder and send it to your clinician. Removing the card 1. Push in the SD card to release it. 2. Remove the card. 3. Insert the card into the protective folder. 4. Send the protective folder back to your clinician as instructed.
PAGE 10
PAGE 11
S9 Escape™ 368870/1 2012-10 S9 Escape POSITIVE AIRWAY PRESSURE DEVICE WELCOME EUR 1/3 Manufacturer: ResMed Ltd 1 Elizabeth Macarthur Drive Bella Vista NSW 2153 Australia. Distributed by: ResMed Corp 9001 Spectrum Center Boulevard San Diego CA 92123 USA. ResMed (UK) Ltd 96 Milton Park Abingdon Oxfordshire OX14 4RY UK. See www.resmed.com for other ResMed locations worldwide. For patent information, see www.resmed.com/ip.