Instructions & Assembly

ManualsBrandsRenin ManualsBi-Fold Interior DoorsEuro 3-Lite Glass Bi-Fold Door

Tools Required for Assembly:

How To Measure Your Finished Opening

3000 Series Bifold Doors

Tools Needed: Phillips Screwdriver, Pencil,

Drill, Measuring Device, 3/16" (5mm) Drill Bit,

3/32" Drill Bit (optional for pilot holes).

Door Layout (4-Door Set)

2 - Door Set

4 - Door Set

Notes:

• Wear Safety Goggles

• Dimensions are in inches

Millimeters are shown in brackets

• Fits normal nished opening height of 80½”

• 2-Door and 4-Door Installations below.

For 4-Door Installations, 2 (two) 2-Door

sets will need to be purchased

FIGURE 1

4-DOOR

MEASURE FROM TOP TO BOTTOM

2 PLACES (HEIGHT)

MEASURE FROM RIGHT TO LEFT

2 PLACES (WIDTH)

Summary of content (7 pages)

PAGE 1
3000 Series Bifold Doors How To Measure Your Finished Opening Tools Required for Assembly: MEASURE FROM RIGHT TO LEFT 2 PLACES (WIDTH) Tools Needed: Phillips Screwdriver, Pencil, Drill, Measuring Device, 3/16" (5mm) Drill Bit, 3/32" Drill Bit (optional for pilot holes). MEASURE FROM TOP TO BOTTOM 2 PLACES (HEIGHT) Notes: • Wear Safety Goggles • Dimensions are in inches Millimeters are shown in brackets • Fits normal finished opening height of 80½” • 2-Door and 4-Door Installations below.
PAGE 2
Step 2- Mount Track Mount Track to header as shown below. From side to side, center the Track in the opening. Use 5EA (max) Long Screws to mount each track. The Upper Pivot should be on the pivoting side of the opening. FIGURE 6 4- DOOR Step 3- Mount Hinges Lay Panels side by side on a flat, clean surface as shown in Figure 7. Push the Panels together and mount hinges in pre-drilled pilot holes. Mount Top/Bottom Hinge as shown in Figure 8. Mount Center Hinge at center of door as shown in Figure 9.
PAGE 3
Step 4- Fasten Mount Plates Fasten Mount Plates as shown below. Mount plates according to the direction of door swing; right swing or left swing as shown in Figures 10 & 11 below. It may be helpful to mark the mount plate holes with a pencil and using a 3/32” drill bit, drill a 1 1/8” deep pilot hole before inserting screws. Note: Make sure the nylon locking arm is on the back of the door.
PAGE 4
Step 6- Mount Lower Jamb Pivot Use a Phillips screwdriver to adjust the Lower Jamb Pivot to the position shown in Figure 14. Mount the Lower Jamb Pivot by placing it directly under the Track on the pivot side as shown in Figures 14 & 15 below. Fasten with 1 EA Long Screw in the slot first to allow adjustment up and down to give clearance between Lower Jamb Pivot and the bottom of the door as shown in Figure 16. Add 2 EA Long Screws to the holes in the Lower Jamb Pivot once adjustments are final.
PAGE 5
Step 8Check Operation, Make Adjustments If necessary use the Wrench supplied to adjust the bolts in the Upper Pivot and Roller to assure the BiFold door set is hanging square in the opening. The Lower Jamb Pivot can be adjusted with a Phillips screwdriver. Arrows in Figure 17 below show directions of adjustments.
PAGE 6
For 4- Door Installs: Attach each Fascia to the upper corner of the Track by removing the tape backing and pushing against track as shown in Figure 19. Cut Fascia if necessary. (Cut with Fascia front up.) Place Fascia Block over the gap at the center of the opening. FIGURE 19 Attach 4- Door Fascia Step 10- Attach The Pull Attach the Pull to the inside stile of the non-pivoting door panel as shown in Figure 1.
PAGE 7
Contents (2 Door Set) 2X Panels 1X Fascia 1X Lower Jamb Pivot 1X Roller 1X Track 1X Bottom Pivot 1X Long Mount Plate 1X Center Hinge 22X Long Screw 1X Fascia Block (for 4 - Door Installation) 1X Short Mount Plate 1X Upper Pivot 1X Snugger 1X Long Spring 2X Top/Bottom Hinge (for 4-Door Installation) 8X Short Screw 1X Pull 1X Wrench 1X Machine Screw (Pull) Step 1- Prepare Track for Mounting Insert components as shown in Figure 2 for 4-Door set or as in Figure 4 for 2-Door set.