User`s manual

ManualsBrandsReflecta ManualsPrint & ScanRPS 7200

Federal Communications Commission (FCC) Statement

This Equipment has been tested and found to comply with the limits for a class B

digital device, pursuant to Part 15 of the FCC rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures :

- Re-orient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from

which the receiver is connected to.

- Consult the dealer or an experienced radio/TV technician for help.

Warning :

Use only shielded signal cables to connect I/O devices to this equipment.

You are cautioned that changes or modifications not expressly approved by the

party responsible for compliance could void your authority to operate the

equipment.

Power Adapter :

Model A:

HIGH POWER HPA-401234U3

Model B:

1800dpi: HIGH POWER HPW-1512A (for USA & Canada)

3600dpi: HIGH POWER HPA-401234U3 or

LINEARITY LAD6019AB4 or

POTRANS 04041120

Summary of content (24 pages)

PAGE 1
Federal Communications Commission (FCC) Statement This Equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
PAGE 2
User’s Manual E N G L I S H
PAGE 3
TABLE OF CONTENTS GETTING STARTED……...………………..……................…………………..2 PACKAGE CONTENTS…………………………………………………………2 E N G L I S H QUICK INSTALLATION GUIDE…………..……...............………………….3 TO INSTALL SOFTWARE AND DRIVER (FOR PC USER)………...…….....3 TO INSTALL SOFTWARE AND DRIVER (FOR MAC USER)……...…….....3 TO INSTALL HARDWARE……………………………………………...…….....4 HOW TO SCAN FILM OR SLIDE…………..……................……………….6 CYBERVIEW X – MF USER’S INTERFACE……...............………………..
PAGE 4
GETTING STARTED Check the package content before getting started. For Quick Installation please refer to Quick Installation Guide. (Ref. Pg. 3~5) E N G L I S H Important! Save the original box, receipt and packing material for possible shipping needs. Package Contents ‧ Film Scanner. ‧ Power Adapter and Cable. Warning! Using any other power adapter may severely damage the scanner and will void the product warranty. ‧ USB Cable. ‧ IEEE1394 Cable. ‧ CyberView X – MF Driver CD.
PAGE 5
QUICK INSTALLATION GUIDE (QIG) TO INSTALL SOFTWARE AND DRIVER… (For PC User) E N G L I S H IF WINDOWS XP IS INSTALLED ON YOUR SYSTEM DURING DRIVER INSTALLATION A LOGO TESTING DIALOGUE BOX MAY APPEAR, IF THIS IS THE CASE PLEASE SELECT “CONTINUE ANYWAY”. Be sure to install the Application Software BEFORE installing the scanner driver CyberViewX –MF. You may install the scanner driver directly if you have already installed TWAIN compliant application software in your computer. a.
PAGE 6
TO INSTALL HARDWARE… Connect The Film Scanner… 1﹒To a power source ‧Make sure scanner is power OFF. ‧Make sure the adapter is complies with local voltage. ‧Plug the AC adapter in AC power source FIRST then plug the other end of power adapter to the port on the back panel of scanner. E N G L I S H 2﹒For product with the USB interface. ‧Attach one end of USB cable to computer. ‧Attach another end of USB cable to the port on the back panel of scanner.
PAGE 7
Notice：If the first film is transparent or blank, please cut it off. Model A 1-1. Turn on the scanner and the computer. 1-2. Clean the filmstrip using compressed air or a soft brush. 1-3. Make sure there is no slide inside the scanner. 1-4. Make sure the image of the film is right side up, feed the filmstrip gently into the upper film entrance until the film is pulled into the scanner. E N G L I S H Model B 1-1. Insert the filmstrip with emulsion side up from the left film entrance. 1-2.
PAGE 8
HOW TO SCAN FILM OR SLIDE Start to Scan… E N G L I S H STEP 1 – Acquire Driver Put the frame or filmstrips into scanner then open Adobe Photoshop Elements or other TWAIN compliant application software. Photoshop Elements... (For PC and MAC User) Open the Photoshop Elements and select “FileÆ Import“ then choose “CyberView X - MF...“ to acquire the TWAIN driver. STEP 2 – Scan Setting ... Select the film type, brand and model. EX：If the film is Fuji 200 Negative then select “Negative ＞ Fuji ＞ Fuji 200“.
PAGE 9
STEP 3 – Pre-scanning... Select the “Prescan Current Frame“ to pre-scan a existing film or “Prescan All“ to pre-scan a filmstrip or a single roll film. 【Single Pre-scan】 E N G L I S H 【Multi-Pre-scan】 Fine Tuning Function: If the first frame is not in the correct position, use the fine tuning function to adjust the first film frame to an accurate location.
PAGE 10
E N G L I S H 【Choose the resolution】 STEP 5 – To Scan Choose “Scan Current Frame” to scan an existing frame or ”Scan All” to scan a filmstrip or a single roll film. 【Single Scan】【Multi-Scan】 STEP 6 – Exit After scanning film(s), all of the images will transfer to the imaging application software (ex：Adobe Photoshop), click the sign of “X” or “Scan ＞ Exit” to close the driver then you can edit, save and print the image from the application software.
PAGE 11
CyberView X – MF USER INTERFACE E N G L I S H 9
PAGE 12
Description of CyberView X - MF There are four major parts of CyberView X – MF user interface E N G L I S H Ⅰ ﹑ Main Window Area【Fixed Windows】 ◆ Menu Command Scan 1. Prescan Prescan Current Frame：Pre-scan an existing frame. Prescan All：Pre-scan a filmstrip or a single roll film you loaded. Prescan…：Pre-scan the current film or designate film(s) separated by comma symbol. 2. Scan 2-1 Scan Current Frame：Scan the current frame. 2-2 Scan Selected：Scan the film(s) you selected.
PAGE 13
i. Select Browse and choose the designated folder you wish to save the scanned image to. ii. Enter the file name. iii. Trailing Index after Base File Name -Digits: user can adjust the digits to define the length of the file name and it Hill support up to 6 digits at most) -Options: use Film Index: Automatically accumulate the number and the default number is 1 user Defined Start Number: user can change the default number iv. Choose the file type to “TIF” or “JPG”. v. Choose image quality in JPEG mode.
PAGE 14
i. “Prescan Resolution“ - To set the default per pre-scan resolution. ii. “Using default real scan resolution“ - Click to select the default scan resolution. iii. “Color Depth“ – To set the default color depth “8 bit” or “16 bit” while scanning. iv. “Scan Mode“ – To set the default scan mode “Normal” or “Quality” mode while scanning. Quality mode will take longer time to scan and image process for better quality. E N G L I S H i.
PAGE 15
iii. “Prescan All” – Pre-scan all frames in filmstrip or roll film after loading the filmstrip. E N G L I S H i. Enable or Disable the “Enable ROC” to start or stop the ROC function default while scanning. ii. Enable or Disable the “Enable GEM” to start or stop the GEM function default while scanning. 7. Exit：Closes the CyberView X-MF user interface. Preview 1. Zoom In：Magnify image. 2. Zoom Out：Reduce image. 3. Rotate 90 Left：Turn the image 90° counter clockwise. 4.
PAGE 16
Image Adjustment 1. Variations：Provides different views of image with options to make changes to highlights midtones etc.
PAGE 17
2. Color Balance...：To adjust the brightness, contrast, saturation, and color (CMY or RGB) of the image. Comparison between before and after adjusted will be shown for reference.
PAGE 18
3. Curves and Levels...：To adjust image quality by moving Curve and Levels. Comparison between before and after adjusted will be shown for reference.
PAGE 19
Windows 1. Exposure Setting...：To adjust the exposure time (R,G, B) press “Reset“ to restore to the default setting. E N G L I S H 2. Output Preview...：To preview the output format of image. A pop-up window to set the output media (type and side), parameter (resolution and size). Help 1. User Manual：Opens the electronic user’s manual. 2. Update Firmware：Upgrade the firmware version, select the path where the file of firmware has been saved. 3. About...
PAGE 20
◆ Function Bar Diagram In order to optimize scanned image quality, please select your film type and brand from the toolbar. E N G L I S H 【Negative】【Positive】【Black and White】 Prescan: Pre-scan the current film, press ▼ button down for more options. Scan: Scan film, press ▼ drop down button for more options. Image Adjustment: Press ▼ drop down button for more options. Output Preview: To display the output preview image. Backward Eject: Eject the roll of film from top.
PAGE 21
Rotate 90 Right : To rotate the image clockwise 90 degrees. Flip Horizontal: To Flip the image 180 degrees horizontally. E N G L I S H Flip Vertical: To Flip the image 180 degrees vertically. Revert: Discard all modifications and restores the image back to the original state in preview windows. ROC: Automatically restores original colors by analyzing the base image and applying corrections to the faded colors. (Function only for ASF Digital ICE3™ function build in model.
PAGE 22
Ⅲ､Active Frame Setting Window Area【Floating Window】 A comprehensive advanced mode is available to allow for more user defined adjustments. Normal mode【ex：I】to set the basic parameter of scan （including scan resolution , film size, color depth）. E N G L I S H Advanced mode【ex：II】to set the parameter of scan and output （including scan resolution, size, color depth and output resolution, size, scan mode）.
PAGE 23
Ⅳ､Thumbnail Panel Window Area【Floating Window】 Displays thumbnail view of pre-scanned images. By default all pre-scanned images are selected. Note the small check mark below each image. E N G L I S H When scanning more than 6 frames (6 at a time are viewable in the thumbnail panel) you may scroll to view more by clicking on the right arrow button. The left / right arrow buttons allow you to scroll through pre-scanned images with ease.
PAGE 24
TECHNICAL SUPPORT CyberView X - MF For question regarding film scanner and CyberView X-MF driver, please contact with your dealer immediatly. E N G L I S H Bundled application software For questions regarding bundled application software, you can refer to the HELP function on the application menu bar or visit the software company’s website. **This user manual has also been archived in the packaged CD.