redi DOO R DOO R ® ® INSTALLATION INSTALLATION INSTRUCTIONS INSTRUCTIONS tile redi ® ® TM TM Redi RediSwing Slide TM.. .. ..
Tools: To install your New Shower Enclosure, you may need the following: Drill Pencil Hack Saw 1/8” & 3/16” Drill Bit Low Tack Tape Caulk Gun Center Punch Tape Measure Clear Silicone Caulk Files 4’ & 6’ Levels Suction Cups #2 Phillips Screwdriver Safety Notes: This unit is best installed by two people. Handle the glass panels carefully and protect the edges.
PARTS LIST ITEM DESCRIPTION QTY.
EXPLODED VIEW RDQCI5301 Rev.
This unit maybe installed with the inner panel to either side. In order to minimize chances of water leakage, please install the inner panel closest to the shower head. Installation with the inner panel opposite of the shower head when closed leaves a gap between the panels that water may pass through. SHOWER HEAD MINIMUM THRESHOLD WITDH This unit requires a minimum 2 3/4” threshold width. The unit requires 2 3/4” of threshold width to ensure the unit does not hang off of the edge.
DRILLING HOLES This unit maybe installed on many types of walls. Please reference this section to determine how to drill holes in your walls based on what material your walls are made of. Fiberglass Enclosure: Use standard 1/8” drill bit to drill holes through the fiberglass wall mate- rial at marked locations. Place a small amount of silicone into each hole before installing the screw. If the fiberglass enclosure will not hold the screw: Drill a 3/16” hole at the marked location.
IDENTIFY GLASS PANELS WALL If the panels have the Redi Clear™ treated glass there will be labels identifying the coated side. In-stall the panels with the coated side to the inside. The Inner Panel has 2 mounting holes lower on the panel and 1 hole for the Knob. The knob mount hole will be against the wall when the panel is closed. RDQCI5301 Rev. 0 The Outer Panel has 2 mounting holes higher on the panel and 2 holes for the Towel Bar.
1 Determine location of the unit centerline on the threshold. Mark a continuous centerline on both walls starting where the threshold centerline meets the wall. Use a level to ensure the wall centerline is plumb and straight. The wall centerline should be a minimum of the unit height from the threshold. RDQCI5301 Rev.
2 Along the threshold, mark the middle point. This will be the location to install the center guide. 3 Place a Wall Jamb on each wall. Align the Wall Jamb with the marked centerline running through the pre-drilled holes. Use a level to confirm the Wall Jamb is plumb. Mark the hole locations. Centerline visible in pre-drilled holes of Wall Jamb RDQCI5301 Rev.
4 Drill the 6 marked locations. Drill holes as described on page 4 5 Set the Wall Jambs in place. Secure with 6 SCR10 Wall Jamb Screws. Install 4 SC4259 Bumpers, 1 each on top and bottom screws. If required, be sure to install wall plugs before securing wall jambs. See page 4 RDQCI5301 Rev.
6 Measure the Wall-to-Wall distance at the top of the Wall Jambs. Record the measurement [T]:_________” 7 Subtract 1/2” from the measurement [T]. [T] - 1/2” = _____________” [HC] Cut the Header to length [HC]. 8 Using a straight edge mark a straight line at the front of the unit as shown. Mark a straight line flush against the front inside edge of the wall jambs. This will ensure the curb is installed without any bows that would impede proper glass movement.
9 Slide the Header Mount Brackets into each side of the Header. Temporarily tighten the mount screw on one side. This is now the Header Assembly. 10 Lower the Header Assem- bly into the Wall Jambs, being sure the Header Mount Brackets slide into the grooves of the Wall Jamb. Rest the Header Assembly on the top Bumpers. Header Assembly Rests on Top Bumpers RDQCI5301 Rev.
11 Use a 4’ level to check the Header Assembly for level. To level the header, lift only 1 side from the Top Bumper. Mark the location of the Header Mount Brackets on the Wall Jambs. 12 Remove the Header Assembly from the Wall Jambs. Remove the Header Mount Bracket from the Header that was not tightened in Step 9 Loose Header Mount Bracket from Step 9 RDQCI5301 Rev.
13 Slide the Header Mount Brackets into each Wall Jamb. The 3 holes face Inside the Shower. Mark from Step 11 Align the Header Mount Brackets with the mark made in STEP 11. Mark the locations of the mounting slots as shown. Be sure the mounting holes are to the inside of the shower PRO-TIP: Make the holes near the top of the adjustment slots. If they are drilled accurately this will prevent the header from slipping out of adjustment in the future.
16 Reassemble the Header and Header Mount Brackets. Re-insert the Header Assembly into the Wall Jambs. 17 Install the SCR02 Header Mount Screws from STEP 15. Re-check the header for level. Make any final adjustments and secure the screws. DO NOT use a power tool to prevent stripping the holes. RDQCI5301 Rev.
18 Using the provided Allen Wrench, tighten both Header Set Screws. 19 Measure the Threshold Width [TW]: __________ SUBTRACT 5/8” Cut the Curb Length [CL] to:___________ 20 If the Silencer Vinyl was not already inserted, slide the SCV190 Silencer Vinyl into the Track. Trim to length. This is the Track Assembly. RDQCI5301 Rev.
21 Position the Track Assembly on the threshold with the front edge on the line marked in Step 8. The front of the track will contact the front inside edge of each wall jamb. Use a pencil to mark both inside and outside edges of the curb. 22 While keeping the Track Assembly straight and on the line, position the Center Guide. It locks into the Track Assembly and the mounting hole should be centered on the line marked in Step 2. Mark the mounting screw location. RDQCI5301 Rev.
23 Remove the Track Assembly and Center Guide. Drill hole as described on page 4 at the marked location. 24 Apply a 3/16” bead of silicone to the threshold between the lines marked to identify the inside and outside edge of the Track Assembly. Carefully put the Track Assembly into place on the threshold. Use masking tape near the ends of the Track Assembly to keep it positioned on the threshold while the silicone cures. RDQCI5301 Rev.
25 Install the rollers on the outer panel. The rollers will be on the inside of the shower. -The rollers are mounted to adjustable cams. Install them with the rollers at the lowest position. -Temporarily install the anti-jumps parallel to the floor. -Only snug the screws for now. NOTE: There are small part numbers on each part of the roller. All of them will face the glass. 26 Install the rollers on the inner panel. The rollers will be on the outside of the shower.
27 To prevent scratching the header during glass installation, apply masking tape to the front face of the header. Place the Inner panel inside the shower, but DO NOT hang it. Protect the glass from contacting hard surfaces. 28 Lift the Outer Panel Assembly into place. Set the rollers in their grooves on the top of the header. Make sure the glass is inside the lip on the track. It is easiest to set the glass near the middle of the header. The glass is not secure yet. Do not leave unattended.
30 Slightly loosen the screws in both Roller Assemblies. Turn the Anti-Jump to vertical to latch them to the Header Assembly. It maybe necessary to press the Door Assembly towards the header at the roller locations. Retighten the screws after adjusting the Anti-Jump. View from Inside Adjust the Anti-Jump to latch seat under the lip on the header 32 Slide the Outer Panel to 1 31 Temporarily remove the inner wall. Lift the Inner Panel into place from inside the shower. portion of the Center Guide.
33 Replace the inner portion of the Center Guide 34 Carefully move each panel to its closed position. As required, slightly loosen the screws in each roller to adjust each panel. The panels should contact both bumpers on the wall they close against. After adjustment for gaps at the walls, final tighten the screws in each roller. 35 Header Cut Length [HC]:__________” From STEP 7 Subtract : 1/2” Anti Jump Length [AJ]:_______” Cut the Anti-Jump Vinyl to length [AJ].
36 Push the inner panel to 1 wall. Slide 1 piece of Anti-Jump Vinyl behind the inner panel. Near the other wall, begin snapping the Anti-Jump Vinyl onto the Header. For best results, leave 1/4” between the end of the header and the Anti-Jump Vinyl. Continue snapping the vinyl onto the header towards the center of the unit. SNAP ANTI-JUMP VINYL ONTO LIP OF HEADER AS SHOWN 37 Repeat for the other Anti-Jump Vinyl piece. Push the inner panel to the other wall.
38 The Inner Panel Rollers and outer portion of the Outer Panel Rollers use the same caps. They snap on. If they do not snap, use a small amount of silicone to hold them in place. 39 The Inner Covers for the Outer Panel Rollers slide down and snap into place. QCI5301 Rev 0 RDQCI5301 Rev.
40 Install the Finger Pull. The longer side goes INSIDE the shower. CAUTION Installing the long side of the knob to the outside will lead to breaking 1 or both pieces of glass. Be sure to install the long side of the knob to the inside of the shower! 41 Install the Towel Bar on the Outer Panel. It is installed facing out. 42 Carefully remove any masking tape used during installation. RDQCI5301 Rev.
43 Apply a small continuous bead of silicone where the walls and threshold meet the metal of the shower door (Track and Wall Jamb). Apply a small continuous bead of silicone around the Center Guide. Be sure to silicone the inside and outside perimeter of the door. NOTE: DO NOT USE the shower until the silicone is completely cured. Check the tube of silicone for the manufacturer recommended cure time (typically 24 - 48 hours). RDQCI5301 Rev.
