redi DOO R DOO R ® ® INSTALLATION INSTRUCTIONS tile redi ® ® TM TM RediScreen SwingTM . . .
Tools: To install your New Shower Enclosure, you may need the following: Drill Pencil Hack Saw 1/8” & 3/16” Drill Bit Low Tack Tape Caulk Gun Center Punch Tape Measure Clear Silicone Caulk Files 4’ & 6’ Levels Suction Cups #2 Phillips Screwdriver Safety Notes: This unit is best installed by two people. Handle the glass panels carefully and protect the edges.
PARTS LIST ITEM 1 2 3 4 5 6 DESCRIPTION FIXED DOOR PANEL WALL MOUNT CLAMP U-CHANNEL #8 X 1 1/2 TRUSS HEAD SCREW PLASTIC WALL ANCHOR 1/8 SETTING BLOCK QTY. 1 1 1 4 4 2 *Quantities may vary. **Support bar only included if necessary. RDQCI5283 Rev.
EXPLODED VIEW RDQCI5283 Rev.
If a continuous unit centerline does not exist from the original measuring process, it will be necessary to create one. Referencing the Measuring Guide included with this unit, lightly mark a continuous unit centerline on the threshold. Next, mark a continuous unit centerline up each wall, starting where the threshold centerline meets the wall. Use a level to ensure the wall centerline is plumb and straight. The wall centerlines should be a minimum of the unit height from the threshold.
* Remove u-channels from the hardware box and countersink holes in the u-channels. Each piece of u-channel requires a minimum of two (2) screws, 3” from each end for lengths less than 18”. Lengths 18” or greater also require screws approximately every 18”-24. Each piece of u-channel is cut to length and mitered as necessary. Position each piece of u-channel along the threshold centerline and use low-tack tape to hold in place.
Place 1/8” setting blocks as shown or approximately every 18”. DO NOT place setting blocks over screw heads. Using suction cups slide the Fixed Panel Glass into the appropriate side. Use setting blocks to make exposed edges of the glass level and plumb. Exposed edges MUST be level and plumb before moving to next step. Using the glass clamp mounting slot on the Fixed Panel Glass as a guide, make a mark on the wall on center w/ the slot.
Using suction cups, set the Fixed Panel Glass back into position. Double check exposed edges of the glass are level and plumb. Exposed edges MUST be level and plumb before moving to next step. INSIDE Place the clamp cover plate on the outside of the glass and secure from the inside w/ the screw provided.
Appendix — A Notch Panel If your unit has been purchased with a notch panel option, two additional pre-cut pieces of u-channel will be provided. These two pieces of u-channel will be mitered and cut to size based on the opening dimensions provided with your order. Please follow the same instructions provided for mounting threshold and wall u-channels, to mount the notch panel u-channels. Below are illustrations to clarify the mounting orientations. RDQCI5283 RDQCI5283 Rev.
If a Support Bar was included w/ your package, it is recommended to be installed to make the enclosure rigid. Please see the various mounting configurations and choose one that best suits your shower enclosure arrangement. First, loosen the screw on top of the Panel Mount just enough so that it is able to swivel, then place the Support Bar Panel Mount onto the Return Panel Glass within 6” of the door opening. Temporarily tighten set-screw to keep in place.
Other Configurations for the Support Bar: Panel to Wall at 180° using a Panel Mount and a Regular Wall Mount: Panel to Wall at 45° using a Panel Mount and an angled Wall Mount: RDQCI5283 RDQCI5283 Rev.
Installing Towel Bars: Assemble parts as shown. Screw the threaded back plate or screw into the towel bar holding the washers, end plates, and gaskets in place. Align other side of towel bar on opposite side of glass and tighten set screws RDQCI5283 RDQCI5283 Rev.
RDQCI5283 RDQCI5283 Rev.
Tile Ready® Brand Shower Pan Installation Addendum SPECIAL INSTRUCTIONS FOR REDI DOOR® ENCLOSURE INSTALLATIONS WITH TILE READY® BRAND SHOWER PANS Designated screw pack for Tile Ready® Brand Shower Pans: For Redi Door® enclosure installations with a Tile Ready® brand shower pan, a special screw pack containing eight (8) #8x¾” pan-head screws is included with your door. These #8x¾”screws replace curb screws included in the main hardware package, and their use is mandatory.
