Installation Manual

ManualsBrandsRBP ManualsAutomotiveRBP RBP-1215B-RX3 RX-3 Series Step Bar Black

RBP-1215B-RX3/RBP-1215SS/RX3 INSTALLATION INSTRUCTIONS

Page 1 of 6 12/2/14

RBP 13000 TEMPLE AVE. CITY OF INDUSTRY, CA 91746 800-237-7560

HARDWARE INCLUDED

Driver Side RX-3 Side Step

10-1.5mm Hex Threaded Inserts

Passenger Side RX-3 Side Step

10-1.5mm x 35mm Hex Bolts

Driver Side Modular Rear Bracket

10mm Lock Washers

Passenger Side Modular Rear Bracket

10mm x 20mm OD x 2mm Flat Washers

“L” Support Brackets

8-1.25 x 25mm Hex Bolt

Hole Template Plate

8mm x 22mm OD x 2mm STD Flat Washer

10mm Insert Tool

8mm x 16mm OD x 1.6mm Small Flat Washer

10-1.5mm Clip-On Nuts

8-1.25mm Nylon Lock Nuts

RECOMMENDED TOOLS

13mm Wrenches

3/8” Torque Wrench

3/8” Ratchet with 3” and/or 6” Extension

Electric Drill

RBP-1215B-RX3/RBP-1215SS-RX3 2002-2017 DODGE RAM 15 - 3500

QUAD CAB RX3

Front

Driver side RX-3 Side Step

Passenger side RX-3 Side Step

Drill Template

(6) “L” Support Brackets

Driver side rear

Modular Bracket

Passenger side rear

Modular Bracket

Summary of content (6 pages)

PAGE 1
RBP-1215B-RX3/RBP-1215SS/RX3 INSTALLATION INSTRUCTIONS RBP-1215B-RX3/RBP-1215SS-RX3 2002-2017 DODGE RAM 15 - 3500 QUAD CAB RX3 Passenger side RX-3 Side Step Drill Template Front (6) “L” Support Brackets Passenger side rear Modular Bracket Driver side rear Modular Bracket Driver side RX-3 Side Step 1 1 1 1 6 1 1 12 2 HARDWARE INCLUDED Driver Side RX-3 Side Step 12 10-1.5mm Hex Threaded Inserts Passenger Side RX-3 Side Step 13 10-1.
PAGE 2
RBP-1215B-RX3/RBP-1215SS/RX3 INSTALLATION INSTRUCTIONS 1 1 13mm Socket 16mm Socket 1 1 3/8” Drill Bit 7/16” Drill Bit STEP 1 - Remove any old steps and hardware from the truck. STEP 2 - Select the driver side step, (use illustration on page 1), and driver side rear Modular Bracket. Attach the Modular Bracket to the appropriate mounting flange toward the back of the step with (2) 8mm Hex Bolts, (4) 8mm x 16mm Small Flat Washers and (2) 8mm Nylon Lock nuts, (Figures 1, 2 , 14 & 19).
PAGE 3
RBP-1215B-RX3/RBP-1215SS/RX3 INSTALLATION INSTRUCTIONS STEP 8 - Line up the “L” Support Bracket with the hole in the pinch weld. Attach the bracket to the pinch weld with (1) 8mm Hex Bolt, (2) 8mm x 22mm STD Flat Washers and (1) 8mm Nylon Lock nut, (Figures 16—19). Leave hardware loose at this time. STEP 9 - Repeat Steps 6—8 to attach the center and rear support brackets to the pinch weld. STEP 10 - Align and adjust the step to the side of the vehicle. Once properly adjusted, tighten all hardware.
PAGE 4
RBP-1215B-RX3/RBP-1215SS/RX3 INSTALLATION INSTRUCTIONS Line up oval hole in body panel with oval hole in template. Mark both outer hole locations onto body panel Steel drill template Fig 5 Front Fig 6 (2) 10mm U-Nuts Front (Fig 7) Use 7/16” drill bit to drill holes Front Fig 8 Slide the U-Nut into the oval hole. Line up nut with drilled hole (Fig 9) 09-14 driver side mounting locations illustrated Page 4 of 6 RBP 13000 TEMPLE AVE.
PAGE 5
RBP-1215B-RX3/RBP-1215SS/RX3 INSTALLATION INSTRUCTIONS (1) 10mm Hex Bolt (1) 10mm Flat Washer (1) 10mm Hex Threaded Insert Front (Fig 11) 10mm insert tool and hex insert (Fig 10) 09-14 driver side front mounting location Assemble tool as pictured above, (Fig 11). Hold insert in place against body panel by firmly grasping the handle on the tool. Turn the hex bolt (tighten) with wrench to expand insert in body panel. Once Metal Insert is fully compressed, remove the bolt and tool from Metal Insert.
PAGE 6
RBP-1215B-RX3/RBP-1215SS/RX3 INSTALLATION INSTRUCTIONS Mark to drill 3/8” hole through pinch weld 8mm Hex Bolt (2) 8mm STD Flat Washers 8mm Nylon Lock Nut Front (Fig 15) 02-08 driver side front support bracket Front (Fig 16) 02-08 driver side front support bracket 8mm Hex Bolt (2) 8mm STD Flat Washers 8mm Nylon Lock Nut Front Front (Fig 17) 09-14 driver side front support bracket (Fig 18) 09-14 driver side center support bracket (2) 8mm Hex Bolts (4) 8mm Small Flat Washers (2) 8mm Nylon Lock Nuts Rea