Installation Instructions

ManualsBrandsRailBlazers ManualsBuilding materials42" White Aluminum Corner Post

T H E H E I G H T O F Q U A L I T Y

TOOLS & MATERIALS NEEDED

• Hacksaw or metal cutting saw

• Drill

• Drill bits: 1/8", 1/4", 5/32", 7/32"

• 3/8" socket or wrench

• Philips screwdriver

• Measuring tape

• Non-corrosive exterior silicone caulking

All fasteners are included with each component.

Lag bolt

Universal

Connector

(UC) bolt

Flat head screw

Sheet metal screw

Self-drilling screw

Installation Guide

Patents pending © Peak Innovations Inc., 2004

Peak Products America Inc. (U.S.A.)

Peak Products Manufacturing Inc. (Canada)

Peak Products International Inc.

(Outside U.S.A. and Canada)

The Peak Group of Companies:

P.O. Box 33866, Vancouver BC, Canada V6J 4L6

Peak products and the materials associated

therewith are protected by patents, designs,

are used under license and are owned by

Peak Innovations Inc.

NOTE: Universal Connectors (UCs) can be used for either

Horizontal Angle or Stair Applications, mount backing plate

accordingly.

IMPORTANT INFORMATION

PICKET RAILING INSTALLATION

WARNING

No member of the Peak Group of Companies* shall be liable

f o r a n y l o s s o r d a m a g e r e s u l t i n g f r o m t h e i m p r o p e r

installation or use of these products. If any member of the

Peak Group of Companies becomes liable for any loss or

damage, the aggregate liability of the Peak company shall be

limited to the retail purchase price of that product.

Before using these products, ensure areas to

be drilled are free from utilities, services and hazards.

B u i l d i n g c o d e s m a y v a r y. A l w a y s c o m p l y w i t h a l l

applicable building codes.

Backing

Plate

Horizontal Angle

Application

Stair

Application

Wall

mount

brackets

3/8

Post

mount

brackets

1/8"

1/8

3/8"

When securing posts with lag bolts, ensure bolts penetrate

a mi n i mu m o f 1 1 /2 " o f s o li d w o o d . To p r e v e n t w o o d

splitting and rot, drill 5/32" pilot holes and coat lag bolt

threads with non-corrosive exterior silicone caulking.

Ensure posts are plumb.

NOTE: Railings can also be attached to a wall or post

using brackets as shown below.

Measure and mark the position of all posts and space

equally. Lag bolt end post in place. Temporarily position

the second post - do NOT bolt it yet! Cut hand and

base rails to fit between posts. Install base rail support and all

but the last four spacers in each rail.

HELPFUL TIP:

Soap may be used to ease spacer installation.

Spacers

Base rail support

post. Insert picket into base rail and swing top into handrail as

shown below. Repeat to complete section.

Insert rails into first post and use second post as temporary

support - do NOT secure rails yet. Slide all spacers toward

temporary post. Slide first spacer in each rail against first

These products are designed for most residential applications.

1/8

3/8

CDN-0904

* The Peak Group of Companies

P e a k P r o d u c t s M a n u f a c t u r i n g I n c .

(Canada)

Peak Products America Inc. (USA)

Peak Products International Inc. (Outside

Canada & USA)

Summary of content (3 pages)

PAGE 1
IMPORTANT INFORMATION TM WARNING Before using these products, ensure areas to be drilled are free from utilities, services and hazards. B u i l d i n g c o d e s m a y v a r y. A l w a y s c o m p l y w i t h a l l applicable building codes. PICKET RAILING INSTALLATION 1 Measure and mark the position of all posts and space equally. Lag bolt end post in place. Temporarily position the second post - do NOT bolt it yet! Cut hand and base rails to fit between posts.
PAGE 2
3 Remove temporary post to install last few pickets and spacers. Cut last spacers flush with ends of rails. NOTE: to ensure equal picket spacing at each post, cut first and last spacers in hand and base rails to equal lengths. STAIR RAILING INSTALLATION Follow all applicable building codes for stair post placement and heights of rails above nose of stair treads. Note: Stair pickets and spacers are different from regular pickets and spacers. 1 Use Universal Connectors (UCs) at each post.
PAGE 3
GLASS PANEL INSTALLATION 1 Refer to the Picket Railing Installation instructions for rail and post mounting details. Building codes may vary, always comply with all applicable building codes - space posts accordingly. Cut hand and base rails to fit between posts. Remove picket gaskets from both rails. 2 Cut glass gaskets the same length as rails and drill 1/8" holes into base rail glass gasket for water drainage. Press glass gaskets into rails and install base rail support.