Installation Guide

Package Contents
Warnings and Cautions
1of1
Assembly Instruction Sheet #IS-TY1444
For Styles TY1444AN and TY1444WT
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2015 QuoizelInc.
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
A
Crossbar Assembly
x1
C
Shade
x4
B
Fixture Body
x1
D
Steel Collar
x4
STEP 3 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Twist
connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires into the Outlet Box.
White wire
from supply
White wire
from fixture
Black wire from
supply (or Red)
Black wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 3
September2015
PART NUMBER
NOTE: ALL DIMENSIONS
ARE ROUNDED UP TO
THE NEAREST 1/4"
1
NO.
PART NUMBER
REPLACEMENT PART
REQ.
G2440SH SHADE 4
TY1444AN/TY1444WT
1
STEP 1 Install Crossbar
Assembly
-
A. Pass the supply wires through
the Crossbar Assembly (A).
Attach the Crossbar Assembly
(A) to the Outlet Box with the
head of the Green Ground
Screw facing you. Secure it
with Outlet Box Screws (not
included). Tighten until snug.
Supply Wires
with Ground Wire
Outlet Box Screws
(not included)
Outlet
Box
Figure 1
STEP 2 Fit Ceiling Canopy to
Crossbar Assembly
-
A.
eiling canopy on
Fixture Body (B) to the
eiling canopy
ceiling
Remove mounting balls from
the Crossbar Assembly (A).
Fit the c
Crossbar Assembly (A) and
secure with mounting balls.
Note: The c
should be
snug against the and
the mounting balls. If
on
Fixture Body (B)
not,
adjust the length of the nipple
Mounting
Screw
Hex Nut and
Lock Washer
B
Mounting Ball
Figure 2
A
on the Crossbar Assembly (A) by unscrewing the preassembled hex
nut and lock washer and then screwing the mounting screws in or out
of the crossbar until the correct length is achieved. Once the ceiling
canopy on Fixture Body (B) is secure, remove the mounting ball and
ceiling canopy and proceed to Step 3.
A
STEP 4 - Install Bulb and Shade
A. Place Shade (C) and Steel Collar (D) over
the Socket, by using Socket Collar Tool (F)
threading Socket Collar (E) onto the Socket.
Hand tighten until sung.
B. This fixture uses standard bulb with medium
base. Maximum 100 watts. Insert bulb and
screw snugly into place.
Your fixture is now assembled and ready
to use. Enjoy!
C. Carefully hold the Shade and the Shade
Holder adjust them to your desired directions.,
Figure 4
Pleasegoto forproductcleaning tips.Goto the selection.
(4)A19MediumBase bulb100WMaximum,Alternate bulb(4)23W CFL.
30-45minutes
Identifyandinspect allpartsbefore beginninginstallation.Check packagecontentlist anddiagramsbelow tobesureall parts are
present.Ifanyparts are missing or damaged, do not attempttoassemble, install, or operate the fixture. Contact customer serviceforreplacement
parts.
www.quoizel.com Care+Maintenance
LightSource:
EstimatedAssembly Time:
Preparation:
ToolsRequired:Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters, wire strippers, electrical tape, safety glasses.
(4) 100W
Bulb
(Not Supplied)
Medium
Base
FINISH: ANTIQUE NICKEL
WESTERN BRONZE
E
Socket Collar
x4
F
Socket
Collar Tool
x1
F
E
D
C
Socket
Bulb
9”
10.5”
5.25”
3.5”Dia.
43.75”
4.75”
9”