Installation Guide

ManualsBrandsQuoizel ManualsSemi-Flush Mount LightsTFVY1716VA

1of2

6 CORPORATE PARKWAY

GOOSE CREEK SC 29445

www quoizel com

Thank you for purchasing a Quoizel product.

Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700

or visit us on-line at www.quoizel.com

2015 QuoizelInc.

Assembly Instruction Sheet #IS-TFVY1716VA

For Style TFVY1716VA

Pleasegoto forproduct cleaningtips. Goto the selection.

(2) A19Medium Base75W bulbMaximum,Alternatebulb (2)19W CFLMaximum.

30-45minutes

Identifyand inspectall partsbefore beginninginstallation. Checkpackage contentlist anddiagrams belowto besure allparts are

present.If anyparts aremissing ordamaged, donot attemptto assemble,install, oroperate thefixture. Contactcustomer servicefor replacement

parts.

www.quoizel.com Care+ Maintenance

LightSource:

EstimatedAssemblyTime:

Preparation:

ToolsRequired:Flathead screwdriver,Phillips screwdriver,pliers, wirecutters, wirestrippers, electricaltape, safetyglasses.

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject

glass parts to any shock while in operation or shattering may result.

Care of Tiffany Style Shade

A new tiffany lamp shade has an oil film applied to the shade that protects the tiffany shade from scratches during shipment. If the oil applied is

too heavy you can remove the excess oil film with a paper towel. Gently wipe away the excess oil.

For general cleaning of tiffany shades use a gentle lemon oil-based furniture polish applied to a soft cloth and wipe gently.

If a white powder appears on the soldered joints of the tiffany shade this is a normal oxidation process. Use a small amount of lemon oil or

mineral oil applied directly to oxidized areas and the soldered area will return to like new.

Package Contents

Crossbar

Assembly

Fixture Body

Shade

Stem 3.5”L

STEP 2 Fit Ceiling Canopy to

Crossbar Assembly

eiling canopy

to the

eiling canopy

ceiling

Remove mounting balls from the

Crossbar Assembly (A). Fit the

c of the Fixture Body

(B) Crossbar Assembly (A)

and secure with mounting balls.

Note: The c should

be snug against the and

the mounting balls. If not, adjust

the length of the mounting screw

Mounting Screw

Hex Nut and

Lock Washer

Mounting Ball

(Step 2 Continued)

on the Crossbar Assembly (A) by unscrewing the preassembled hex

nut and lock washer and then screwing the mounting screws in or out

of the crossbar until the correct length is achieved. Once the ceiling

canopy is secure, remove the mounting ball and ceiling canopy and

proceed to Step 3.

STEP 3 - Wire Connections

A. Use standard wire connectors (not included) to make all wire

connections. (Connectors are not included with fixture.) Twist

connectors until wires are tightly joined together. Wrap each

connection with approved electrical tape and carefully stuff all the

connected wires into the Outlet Box.

White wire

from supply

White wire

from fixture

Black wire from

supply (or Red)

Black wire

from fixture

Ground wire

from supply

Ground wire

from fixture

Figure 3

July2015

Finial

Figure 2

STEP 4 Install Fixture Body-

A. Carefully tuck all wires into the

outlet box and position the

ceiling canopy of the Fixture

Body (B) over the outlet box.

Align the holes in the ceiling

canopy with the mounting

screws, then attach the ceiling

canopy using the previously

removed mounting balls. Hand

tighten until snug.

Figure 4

STEP 5 Install Shade and Bulbs-

A. Thread have no beaded end of Center Stem (C) into the hex coupling

underside of the Fixture Body (B). Hand tighten until snug.

Flat Washer

Mounting Screw

Hex Nut and

Lock Washer

Mounting Ball

STEP 1 Install Crossbar

Assembly

A. Pass the supply wires through

the Crossbar Assembly (A).

Attach the Crossbar Assembly

(A) to the Outlet Box with the

head of the Green Ground

Screw facing you. Secure it with

Outlet Box Screws (not

included). Tighten until snug

Figure 1

Outlet Box

Outlet Box Screw

(not included)

Green Ground

Screw

Summary of content (2 pages)

PAGE 1
Assembly Instruction Sheet #IS-TFVY1716VA For Style TFVY1716VA 6 CORPORATE PARKWAY GOOSE CREEK , SC . 29445 www . quoizel . com Please go to www.quoizel.com for product cleaning tips. Go to the Care + Maintenance selection. Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Light Source: (2) A19 Medium Base 75W bulb Maximum, Alternate bulb (2) 19W CFL Maximum.
PAGE 2
(Step 5 Continued) B. Place the Flat Washer (D) and the Shade (E) over the bottom end of the Stem (C). Secure by threading the Finial (F) onto the Stem (C). Hand tighten until snug. C. This fixture uses standard bulb with medium base . Maximum 75 watts. Insert bulb and screw snugly into place. B C Bulb Your fixture is now assembled and ready to use. Enjoy! D E F Figure 5 TFVY1716VA FINISH: VALIANT BRONZE 16” Dia. 6.25” Dia. 12.5” 6.