Installation Sheet

ManualsBrandsQuoizel ManualsPendantsQuoizel Romain 7 Light 20" Wide Cage Multi Light Pendant

Pleasegoto forproductcleaningtips.Gotothe selection.

Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.

MinimumHangingHeightis16”,MaximumHangingHeightis102”.

MissingParts?Contactyouroriginalplaceof

purchase.

www.quoizel.com Care+Maintenance

ToolsRequired:

LightSource:

FixtureHangingHeight:

(7)A19MediumBaseBulbs75WMaximum,bulbsnotincluded.

EstimatedAssembly Time:

Preparation:

30-45minutes

Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.

Warnings and Cautions

1of3

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.

For Style RMI2707EK

Installation Guide #IS-RMI2707EK

2018 QuoizelInc.

ReleasedDate:2018-11-13

visit us on-line at www.quoizel.com

Package Contents

Crossbar Assembly

Ceiling Canopy

Wire Connectors

Safety Clip

Jumper Wires

White Wire

Black Wire

Green Wire

STEP 1 - Installing the Crossbar Assembly

A. Pass the supply wires from outlet box through the Crossbar

Assembly (A). Attach the Crossbar Assembly (A) to the Outlet Box

with the head of the Green Ground Screw facing you. Secure the

Crossbar Assembly (A) with Outlet Box Screws (not included).

Tighten until snug.

Supply Wires with

Ground Wire

Outlet Box Screws

(not included)

Outlet Box

Figure 2

STEP 2 Test Fitting Ceiling Canopy to Crossbar Assembly-

eiling Canopy to the

ceiling

Remove mounting balls from the Crossbar Assembly (A). Fit the

C (D) Crossbar Assembly (A) and secure with

mounting balls. Note: The should be snug

against the and the mounting balls. If

Ceiling Canopy (D)

not, adjust the length

of the nipple on the Crossbar Assembly (A) by unscrewing the

preassembled hex nut and lock washer and then screwing the

mounting screws in or out of the crossbar until the correct length is

(Step 2 Continued)

achieved. Once the Ceiling Canopy (D) is secure, remove the

mounting ball and Ceiling Canopy (D) and proceed to Step 3.

Mounting Screw

Hex Nut and

Lock Washer

Mounting Ball

Please measure the height you want to hang the pendant prior

to hanging so you know what length to cut the wire. You can add

6" to that length to help adjust the shades up or down once it’s

hung. Please note, all the extra wire will not fit inside the small

canopy and junction box, the wire needs to be cut at the desired

length to fit inside the canopy and junction box to then help

adjust to the exact height.

IMPORTANT: Install the cord into the ceiling canopy before

cutting it to length.

Figure 1

Fixture Body

Summary of content (3 pages)

PAGE 1
Installation Guide #IS-RMI2707EK For Style RMI2707EK Please go to www.quoizel.com for product cleaning tips. Go to the Care + Maintenance selection. Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Light Source: (7) A19 Medium Base Bulbs 75W Maximum, bulbs not included. Fixture Hanging Height: Minimum Hanging Height is 16”, Maximum Hanging Height is 102”.
PAGE 2
STEP 3 - Install Fixture Bodies to Ceiling Canopy C A. Loosen set screws located on the couplings that are mounted to the underside of the Ceiling Canopy (D). Do not remove set screws completely. B. Thread pendant cord through the coupling mounted to the underside of the Ceiling Canopy (D). Adjust cord to the desired length then tighten set screw to hold pendant length in place. C. Install Safety Clips (C) onto the pendant cords by threading the cord through one hole then back through the second.
PAGE 3
STEP 7 - Install Ceiling Canopy RMI2707EK A. Carefully tuck all wires into the outlet box and position the Ceiling Canopy (D) over the outlet box. Align the holes in the ceiling canopy with the mounting screws, then attach the Ceiling Canopy (D) using the previously removed mounting balls. Hand tighten until snug. A FINISH: EARTH BLACK 14” Dia. Mounting Screw D Mounting Ball Figure 7 STEP 8 - Install Bulbs A. Insert bulbs onto sockets and screw snugly into place.