Installation Guide

Package Contents
Pleasegoto forproductcleaningtips.Gotothe selection.www.quoizel.com Care+Maintenance
LightSource:
ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
(5)G9XenonClearbulb ,40WMaximum.
EstimatedAssemblyTime:
Preparation:
20-30minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
(Supplied)
Warnings and Cautions
1of2
Assembly Instruction Sheet #IS-RBN1622CRC
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2015 QuoizelInc.
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Do not touch the bulb with bare hands use a cloth or glove.
Crossbar
x1
STEP 1 Attach Crossbar to
Outlet Box
-
A. Attach the Crossbar (A) to
Outlet Box and secure by
threading Outlet Box
Screws (not supplied) into
the Mounting Holes on the
Outlet Box. Tighten until
snug.
A
C
Fixture
Body
x1
STEP 2 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Twist
connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires into the Outlet Box.
A
White wire
from supply
White wire
from fixture
Black wire from
supply (or Red)
Black wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 2
Figure 1
Outlet
Box
Outlet Box
Screw
STEP 4 - Install Bulbs
IMPORTANT:
A. This fixture uses clear G9
bulb ( ) with G9 base. Maximum
40 watts. Insert bulb and push
snugly into place.
Do not touch the
bulb with bare hands use a cloth
or glove.
Xenon
D
Figure 4
D
G9 Clear
Xenon Bulb
x5
April2015
Mounting Screw
x2
B
E
Stem
x15
F
Trimming
x15
G
H
Rubber
Washer
x30
Lock Ball
x15
STEP 3 Attach Ceiling Canopy
to Crossbar
-
A. Line up the Hole on the Fixture
Body (C) and the Mounting
Hole on the Crossbar (A),
secure by thread the Mounting
Screw (B) into the Mounting
Hole. Tighten until sung.
Figure 3
B
A
C
Hole
Socket
D
STEP 5 Install Trimming to Fixture-
A. Thread the Short Nipple end of Stem (E) into the Fixture Body (C),
hand tighten until snug.
B. Peel off Protective Films on Trimmings (F).
Note: Gloves are required to avoid leaving fingerprints or scratches
on Trimmings (F).
Figure 5
For Style RBN1622CRC
F
H
G
E
Protective
Film
C. Place the Trimming (F)
and Rubber Washer (G)
over the other end of Stem
(E). Secure by threading
Lock Ball (H) onto the
Stem (E). Hand tighten
until snug.
Your fixture is now
assembled and ready to
use. Enjoy!