Installation Guide

Package Contents
Pleasegoto forproductcleaningtips.Gotothe selection.
Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
www.quoizel.com Care+Maintenance
ToolsRequired:
LightSource:
(4)G9XenonFrostedbulb ,40WMaximum.
EstimatedAssemblyTime:
Preparation:
20-30minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
(Supplied)
Warnings and Cautions
1of2
Assembly Instruction Sheet #IS-RBN1616
For Styles RBN1616C, RBN1616SG, RBN1616MN,
RBN1616W, and RBN1616WT
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2015 QuoizelInc.
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Do not touch the bulb with bare hands use a cloth or glove.
Crossbar
x1
A
C
Fixture
Body
x1
D
G9 Bulb
x4
March2015
Mounting
Screw
x2
B
E
Stem
x9
F
Trimming
x9
G
H
Rubber
Washer
x18
Lock Ball
x9
STEP 1 Attach Crossbar to
Outlet Box
-
A. Attach the Crossbar (A) to
Outlet Box and secure by
threading Outlet Box
Screws (not supplied) into
the Mounting Holes on the
Outlet Box. Tighten until
snug.
A
Figure 1
Outlet
Box
Outlet Box
Screw
C. Connect White Supply Wire from the Outlet Box to Wire Labeled
"N" from fixture.
D. Connect Black (or Red) Supply Wire from the Outlet Box to Wire
Labeled "L” from fixture.
E. Connect Ground Wire from the Outlet Box to Green Striped Wire
from fixture.
F. Twist connectors until wires are tightly joined together.
G. Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
Figure 2
Wire Labeled
“N" from fixture
Wire Labeled
"L" from fixture
Green Striped
wire from fixture
White wire
from supply
Black wire from
supply (or Red)
Ground wire
from supply
STEP 2 Make Wire Connections-
B. If the electrical wire is going to be cut shorter than provided you will
need to identify the "L" line wire and the "N" wire before you cut the
excess wire off. One is labeled N and the other labeled L. The third
wire has a green stripe on it. To do this strip back the clear wire
covering the 3 fixture wires as far as you need to. This will expose
each fixture wire individually. Separate the "L" wire from the other
two and re-label the wire near where you want to make the cut. Be
sure to mark the wire on the side of the fixture and not on the
excess wire being cut and removed. Do the same labeling with the
"N" wire.
A. Use standard wire connectors to make all wire connections.
(Connectors are not included with fixture.) Strip and prepare wire
ends according to instructions supplied with connectors.
STEP 3 - Attach Ceiling
Canopy to
Crossbar
A. Line up the Hole on the
Fixture Body (C) and
the Mounting Hole on
the Crossbar (A),
secure by thread the
Mounting Screw (B)
into the Mounting Hole.
Tighten until sung.
A
B
C
Hole
STEP 4 - Install Bulbs
IMPORTANT:
A. This fixture uses frosted
G9 bulb ( ) with G9
base. Maximum 40 watts.
Insert bulb and push
snugly into place.
Do not touch
the bulb with bare hands
use a cloth or glove.
Xenon D
D
Socket