Instructions / Assembly

1of1
For Style QW4071PK, HO and WSQW4071 QW4071
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
Pleasegoto forproductcleaningtips.Gotothe selection.
(1)B10CandelabraBasebulbs60WMaximum,bulbnotincluded.
30-45minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtoensureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.MissingParts?Contactyouroriginalplaceof
purchase.
www.quoizel.com Care+Maintenance
LightSource:
EstimatedAssemblyTime:
Preparation:
ToolsRequired: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Installation Guide
2019 QuoizelInc.
ReleasedDate:2019-04-11
visit us on-line at www.quoizel.com
Package Contents
Fixture Body
x1
B
Shade
x1
Figure 1
Figure 3
Green Ground Screw
on the Crossbar
White wire
from outlet box
White wire
from fixture
Black wire from
outlet box (or Red)
Black wire
from fixture
Bare, or Green
Ground wire
from outlet box
Ground wire
from Fixture
STEP 3 - Wire Connections
A.
B. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
Wrap bare or green ground wire around green ground screw on the
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
C
STEP 4 - Install Shade, Glass and Bulb
a. Thread the stem (E) onto the coupling on fixture. Hand-tighten until
snug.
b. Place Glass (D) over the stem (E), Secure with the Finial (F),
Hand-tighten until snug.
c. Place the shade (C) over the candle cover.
d. Insert bulbs onto sockets and screw snugly into place.
Your fixture is now assembled and ready to use. Enjoy!
A
Crossbar Assembly
x1
Glass
x1
D
Stem
x1
E
Finial
x1
F
Supply Wires with
Ground Wire
Outlet Box Screws
(not included)
Outlet Box
A
Bulb
(not included)
E
F
D
B
STEP 1 Installing the Crossbar Assembly-
A. Pass the supply wires through the Crossbar Assembly (A). Attach
the Crossbar Assembly (A) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure the Crossbar Assembly (A)
with Outlet Box Screws (not included). Tighten until snug.
STEP 2 Test Fit the Backplate to the
Crossbar Assembly
-
A. Remove the mounting balls from the
Crossbar Assembly (A). Place the
backplate and Fixture Body (B) onto
the Crossbar Assembly (A) and secure
with mounting balls. Note: The
backplate and Fixture Body (B) should
be snug against the wall and held tight
with the mounting balls. If it is not,
adjust the length of the mounting
screws on the Crossbar Assembly (A)
by unscrewing the preassembled hex
nut and lock washer and then screwing
the mounting screws in or out of the
crossbar until the correct length is
achieved. Once the backplate and
Fixture Body (B) is secure, remove the
mounting ball and Fixture Body (B) and
proceed to Step 3.
Mounting
Ball
A
Backplate
Hex Nut and
Lock Washer
Mounting Screw
Figure 4
candle cover
C
G
Alternate
Mounting screw
x2