Installation Sheet

ManualsBrandsQuoizel ManualsPendantsQuoizel Wilcox Single Light 14" Wide Pendant

1of2

For Style QPP5112WZ

Package Contents

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.

Fixture Loop

Shade

Hardware Contents

Crossbar

Assembly

Ceiling

Canopy

Quick Link

Pleasegoto forproductcleaningtips.Gotothe selection.

(1)A19MediumBasebulb100WMaximum,bulbnotincluded.

MinimumHangingHeightis17.5”,MaximumHangingHeightis53.5”.

30-45minutes

Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtoensureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactyouroriginalplaceofpurchase.

www.quoizel.com Care+Maintenance

LightSource:

FixtureHangingHeight:

EstimatedAssembly Time:

Preparation:

ToolsRequired:Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.

Installation Guide #IS-QPP5112WZ

12” Rod

6” Rod

Socket Assembly

STEP 1 Install Fixture Loop and

Rods to Fixture Body

A. Determine the Rods (B/C) to be

assembled to the Socket Assembly

(F) according to your hanging

height.

B. Pass the supply wires and ground

wire through the chosen rods (B/C)

and the Fixture Loop (A). Thread

the , the

chosen Rods (B/C) and the Fixture

Loop (A) together. Hand tighten

until snug.

Socket Assembly (F)

Figure 1

Supply

Wires and

Ground Wire

2019 QuoizelInc.

ReleasedDate:2019-01-26

visit us on-line at www.quoizel.com

Suggested rods for Ceiling

height :

8’ ceiling : use (1) 6” rod

and (1) 12” rod

9’ ceiling : use (1) 6” rod

and (2) 12” rods

10’ ceiling : use (2) 6” rods

and (2) 12” rods

STEP 2 - Install the Crossbar Assembly to Outlet Box and Adjust

the length of the Nipple

A. Attach the Crossbar Assembly (AA) to the Outlet Box with the head

of the Green Ground Screw facing you. Secure it with Outlet Box

Screws (not included), tighten until snug

B. Adjust the hex nut and lock washer underside of the crossbar to the

middle of the nipple.

C. Remove the canopy lock ring from the canopy chain loop. Place the

Ceiling Canopy (CC) over the canopy chain loop against the ceiling

to determine the correct position of the nipple. Thread the canopy

lock ring onto the canopy chain loop. Adjust the nipple to allow the

Ceiling Canopy (CC) to rest against the ceiling when held in place by

the canopy lock ring.

D. Remove the canopy lock ring and the Ceiling Canopy (CC). Tighten

the lock washer and the hex nut against the crossbar to secure in

place.

Outlet Box Screw

(not included)

Hex Nut and

Lock Washer

Outlet Box

Green Ground Screw

Canopy Chain Loop

Canopy Lock Ring

Nipple

Figure 2

STEP 3 - Install the Fixture Chain and Ceiling Canopy

A. Pull the supply wires and ground wire through the canopy lock ring

and the Ceiling Canopy (CC) in order.

B. Connect the Fixture Loop (A) to the single chain by using the Quick

Link (BB). The fixture will now hang safely.

C. Feed the supply wires and ground wire through the canopy chain

loop and nipple into the outlet box. Cut the wires leaving

approximately 8” of wire extending from the outlet box.

D. Go to Step 4 for wire connections and follow the directions. Return

Lock Screw

Socket Collar

Cage

Summary of content (2 pages)

PAGE 1
Installation Guide #IS-QPP5112WZ For Style QPP5112WZ Please go to www.quoizel.com for product cleaning tips. Go to the Care + Maintenance selection. Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Light Source: (1) A19 Medium Base bulb 100W Maximum, bulb not included. Fixture Hanging Height: Minimum Hanging Height is 17.5”, Maximum Hanging Height is 53.5”.
PAGE 2
(Step 3 Continued) STEP 6 - Install Cage to Step E in this step when complete with Step 4. E. Raise the Ceiling Canopy (CC) and canopy lock ring up the Quick Link (BB) and over the canopy chain loop. Tighten the canopy lock ring onto the canopy chain loop until tight. Supply Wires and Ground Wire A. Place the Cage (H) onto the bottom of the Shade (G) and secure with Lock Screws (D). Hand tighten until snug. Nipple Canopy Chain Loop Your fixture is now assembled and ready to use.