Installation Sheet

1of2
For Style QF4022BN
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
Pleasegoto forproductcleaningtips.Gotothe selection.
(7)B10CandelabraBasebulbs60WMaximum,bulbnotincluded.
MinimumHangingHeightis32.5”,MaximumHangingHeightis68.5”.
30-45minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtoensureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.MissingParts?Contactyouroriginalplaceof
purchase.
www.quoizel.com Care+Maintenance
LightSource:
FixtureHangingHeight:
EstimatedAssemblyTime:
Preparation:
ToolsRequired: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Installation Guide #IS-QF4022BN
2018 QuoizelInc.
visit us on-line at www.quoizel.com
ReleasedDate:2018-08-27
Package Contents
A
Fixture Loop
x1
B
6” Rod
x2
C
Fixture
Body
x1
Hardware Contents
AA
BB
CC
D
12” Rod
x2
STEP 1 Install Fixture Loop and Rods to Fixture Body-
A. Determine the Rods (B/C) to be assembled to the Fixture Body
(D) according to your hanging height.
B. Pass the supply wires and ground wire through the chosen rods
(B/C) and the Fixture Loop (A). Thread the Fixture Body (D), the
chosen Rods (B/C) and the Fixture Loop (A) together. Hand
tighten until snug.
Suggested rods for Ceiling height :
8’ ceiling : use (1) 6” rod
9’ ceiling : use (1) 6” rods and (1) 12” rods
10’ ceiling : use (1) 6” rods and (2) 12” rods
Figure 1
Supply
Wires and
Ground Wire
C
A
B
B
D
C
STEP 2 - Install the Crossbar Assembly to Outlet Box and Adjust
the length of the Nipple
A. Attach the Crossbar Assembly (AA) to the Outlet Box with the head
of the Green Ground Screw facing you. Secure it with Outlet Box
Screws (not included), tighten until snug
B. Adjust the hex nut and lock washer underside of the crossbar to the
middle of the nipple.
C. Remove the canopy lock ring from the canopy chain loop. Place the
Ceiling Canopy (CC) over the canopy chain loop against the ceiling
to determine the correct position of the nipple. Thread the canopy
lock ring onto the canopy chain loop. Adjust the nipple to allow the
Ceiling Canopy (CC) to rest against the ceiling when held in place by
the canopy lock ring.
D. Remove the canopy lock ring and the Ceiling Canopy (CC). Tighten
the lock washer and the hex nut against the crossbar to secure in
place.
.
Outlet Box Screw
(not included)
Hex Nut and
Lock Washer
Outlet Box
Green Ground Screw
Canopy Chain Loop
Canopy Lock Ring
Nipple
AA
CC
Figure 2
Crossbar
Assembly
x1
Ceiling Canopy
x1
Quick Link
x1