Installation Sheet

ManualsBrandsQuoizel ManualsPendantsQuoizel 6 Light 17-1/2" Wide Pendant

1of2

Assembly Instruction Sheet #IS-QF3395GF

For Style QF3395GF

6 CORPORATE PARKWAY

GOOSE CREEK SC 29445

www quoizel com

Package Contents

Hardware Contents

Crossbar

Lock Washer

Hex Nut

Nipple

Canopy

Chain Loop

Canopy Lock

Ring

Ceiling

Canopy

Fixture Chain

Quick Link

Pleasegoto forproductcleaningtips.Gotothe selection.

(6)ClearG9XenonBulbs60WMaximum(supplied).

30-45minutes

Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement

parts.

www.quoizel.com Care+Maintenance

LightSource:

EstimatedAssemblyTime:

Preparation:

ToolsRequired: Flathead screwdriver,Phillipsscrewdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.

2016 QuoizelInc.

Thank you for purchasing a Quoizel product.

Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184

or visit us on-line at www.quoizel.com

ReleasedDate:2017-09-07

Fixture Body

Figure 1

STEP 1 Install the Crossbar to the junction box-

A. Attach the Crossbar (AA) to the Outlet Box with the head of the

Green Ground Screw facing you. Secure it with Outlet Box Screws

(not included), tighten until snug

Outlet Box

Outlet Box Screw

(not included)

Green Ground

Screw

STEP 2 Install the Canopy Chain Loop and Nipple-

A. Thread one Hex Nut (CC) to one end of the Nipple (DD) until it is at

least 0.25” from the end. Pass one Lock Washer (BB) over the end

of the Nipple (DD) and thread the Canopy Chain Loop (EE) onto the

Nipple (DD). By using pliers, thread the Hex Nut (CC) against the

Canopy Chain Loop (EE) and hand tighten until snug.

B. Thread another Hex Nut (CC) to the middle of the Nipple (DD).

Place another Lock Washer (BB) over the Nipple (DD) and then

thread the Nipple (DD) into the Crossbar (AA) until the Nipple (DD)

is about 0.375” above the Crossbar (AA).

Step B

Step A

Figure 2

C. Remove the Canopy Lock

Ring (FF) from the Canopy

Chain Loop (EE). Place the

Ceiling Canopy (II) over the

Canopy Chain Loop (EE)

against the ceiling to

determine the correct

position of the Nipple (DD).

Thread the Canopy Lock

Ring onto the Canopy

Chain Loop (EE). Adjust the

Nipple (DD) to allow the

Ceiling Canopy (II) to rest

against the ceiling when

held in place by the Canopy

Lock Ring (FF).

D. Remove the Canopy Lock

Ring (FF) and the Ceiling

Canopy (II). Tighten the

Hex Nut (CC) against the

Crossbar (AA) to secure in

place.

Clear Glass (A1)

x35

Amber Glass (A2)

x35

Clear Glass (B1)

x23

Amber Glass (B2)

x23

Clear Glass (C1)

Amber Glass (C2)

STEP 3- Install the Fixture Chain and Ceiling Canopy

A. Adjust the Fixture Chain (GG) to your desired length by removing

links if needed.

B. Pull the supply wires through the Fixture Chain (GG) alternating

links. After the wires are through the Fixture Chain (GG), pull the

Supply Wires and the Ground Wire through the Canopy Lock Ring

(FF) and the Ceiling Canopy (II) in order.

C. Attach one end of the Fixture Chain (GG) to the Fixture Loop with

one Quick Link (HH). Lift the fixture and Fixture Chain (GG) up and

attach the other end of the Fixture Chain (GG) onto the Canopy

Chain Loop (EE) with another Quick Link (HH). The fixture will now

hang safely.

D. Feed the Supply Wires and Ground Wire through the Canopy Chain

Loop (EE) and Nipple (DD) into the Outlet Box. Cut the wires leaving

approximately 8” of wire extending from the Outlet Box.

Clear G9

Xenon Bulb

Summary of content (2 pages)

PAGE 1
Assembly Instruction Sheet #IS-QF3395GF For Style QF3395GF 6 CORPORATE PARKWAY GOOSE CREEK , SC . 29445 www . quoizel . com Please go to www.quoizel.com for product cleaning tips. Go to the Care + Maintenance selection. Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Light Source: (6) Clear G9 Xenon Bulbs 60W Maximum (supplied).
PAGE 2
STEP 5 - Install Bulbs E. Go to Step 5 for wire connections and follow the directions. Return to Step F in this step when complete with Step 5. F. Raise the Ceiling Canopy (II) and Supply Canopy Lock Ring (FF) up the Wires and Fixture Chain (GG) and over the Ground Wire Canopy Chain Loop (EE). Tighten the Canopy Lock Ring (FF) onto GG the Canopy Chain Loop (EE) until tight. A. Insert bulbs (H) into sockets and push snugly into place.