Installation Sheet

1of2
For Style PCWN2818EK
Installation Guide IS-PCWN2818EK#
Pleasegoto forproductcleaningtips.Gotothe selection.
Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
LED56W
MinimumHangingHeightis22.25”,MaximumHangingHeightis114.25”.
Contactyouroriginalplaceofpurchase.
www.quoizel.com Care+Maintenance
ToolsRequired:
LightSource:
FixtureHangingHeight:
EstimatedAssemblyTime:
Preparation:
30-45minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
2018 QuoizelInc.
ReleasedDate:2018-08-15
visit us on-line at www.quoizel.com
Package Contents
Fixture Body
x1
D
STEP 1 Adjust Fixture Height-
A. Unlock set screw on the cable
clamp by using the Allen
Wrench (C).
B. Push each button on the bottom
of the ceiling canopy to adjust
the cable or the cord in or out of
the ceiling canopy to achieve
your desired hanging height.
Make sure the cord length and
cable length are the same after
adjustment.
C. Once your desired hanging
height is achieved, move the
cable clamp next to hex nut
inside of the ceiling canopy and
tighten the set screw with the
Allen Wrench (C).
D. Move the safety clip next to the
hex nut inside of the ceiling
canopy.
Ceiling Canopy
Button
Cord
B
Mounting Screw
x2
GN
D
A
Inner Backplate
x1
C
Allen Wrench
x1
Set Screw
Cable Clamp
C
Safety Clip
Cable
Figure 1
STEP 2 Attach Inner Backplate to Outlet Box-
A. Attach the Inner Backplate (A) onto the outlet box and secure with
outlet box screws (not included). Hand tighten until snug with
screwdrivers.
Supply Wires with
Ground Wire
Outlet Box Screw
(not included)
Outlet Box
A
Figure 2
Figure 3
STEP 3 - Wire Connections
A. Wrap bare or green ground wire around green ground screw on the
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
B. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
Green Ground Screw
on the Crossbar
White wire
from outlet box
White wire
from fixture
Black wire from
outlet box (or Red)
Black wire
from fixture
Bare, or Green
Ground wire
from outlet box
Ground wire
from Fixture
STEP 4 Attach Ceiling
Canopy to Inner Backplate
-
A. Fit excess cord and electrical
wires in the ceiling
canopyproperly. Line up the
holes on the side of the ceiling
canopy to the mounting holes
on the Inner Backplate (A).
Secure them with Mounting
Screws (B). Tighten until sung.
Your fixture is now assembled
and ready to use. Enjoy!
B
A
Figure 4
Ceiling
Canopy