Installation Guide

Package Contents
Pleasegoto forproductcleaningtips.Gotothe selection.
Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
Integrated17WLED
www.quoizel.com Care+Maintenance
ToolsRequired:
EstimatedAssemblyTime:
Preparation:
20-30minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
Warnings and Cautions
1of2
Assembly Instruction Sheet #IS-MYS1612C
For Style MYS1612C
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2016 QuoizelInc.
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Crossbar Assembly
x1
A
F
Fixture Body
x1
Mounting Screw
x2
B
February2016
G
Tube
x1
H
Shade
x1
J
Finial
x1
Wall Anchor
x2
C
Self-tapping Screw
x2
D
STEP 1 Attach Crossbar Assembly to Outlet Box-
A. Attach the Crossbar Assembly (A) onto the Outlet Box and make two
marks on the ceiling from keyholes on the flat strap of the Crossbar
Assembly (A).
B. Remove the Crossbar Assembly (A) and drill proper holes on the
ceiling from marks. Insert Wall Anchors (C) into the holes properly.
Attach the Crossbar Assembly (A) to Outlet Box. Thread Outlet Box
Screws (not Supplied) into mounting holes on the Outlet Box. Pass
Washers (E) over Self-tapping Screws (D) and thread Self-tapping
Screws (D) into Wall Anchors (C). Hand tighten until snug.
A
Figure 1
Outlet
Box
C
D
Outlet Box Screws
(not Supplied)
Keyhole
White wire
from supply
White wire
from fixture
Black wire from
supply (or Red)
Black wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 2
STEP 2 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Twist
connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires between Crossbar Assembly (A) and Fixture
Body (F).
Figure 3
STEP 3 - Attach Fixture Body to Crossbar
A. F
. Attach the Fixture Body (F) over the
Crossbar Assembly (A) and line up the hole on the side of the ceiling
canopy to the mounting holes on the ends of flat strap. Secure with
the Mounting Screws (B) and hand tighten until snug.
it excess cord and electrical wires in the ceiling canopy of the
Fixture Body (F) properly
B
A
F
STEP 4 Install Shade-
A. Thread the Tube (G) onto the
nipple on the bottom center of
the Fixture Body (F). Hand
tighten until snug.
B. Attach the Shade (H) onto the
end of the Tube (G). Place the
Rubber Washer (I) onto the
Finial (J) and thread the Finial
(J) onto the Tube (G) to secure
the Shade (H). Hand tighten
until snug.
G
J
H
F
Figure 4
Nipple
Washer
x2
E
I
Rubber Washer
x1
E
I