Installation Sheet

ManualsBrandsQuoizel ManualsPendantsQuoizel Kingfield Single Light 6" Wide Mini Pendant with Etched Glass Shade

1of2

6 CORPORATE PARKWAY

GOOSE CREEK SC 29445

www quoizel com

Assembly Instruction Sheet #IS-KGF1506BN

For Style KGF1506BN

Pleasegoto forproductcleaningtips.Gotothe selection.

(1)A19MediumBaseBulb100WMaximum

30-45minutes

Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement

parts.

www.quoizel.com Care+Maintenance

LightSource:

EstimatedAssembly Time:

Preparation:

ToolsRequired: Flathead screwdriver,Phillips screwdriver,pliers, wire cutters, wire strippers, electrical tape, safety glasses.

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.

Package Contents

Crossbar Assembly

Thank you forpurchasing a Quoizelproduct.

Need assistance withparts or assembly?Call Quoizel customerservice at 1-800-645-3184

or visit us on-line at www.quoizel.com

Shade

2018 QuoizelInc.

ReleasedDate:2018-01-10

Socket

Assembly

Ceiling

Canopy

STEP 1 -

Socket Assembl

Install Ceiling Canopy, Rods and

y together

A. Determine the Rods (B/C) to be

assembled to the Socket Assembly (E)

according to your hanging height.

B. Pass the supply wires and ground wire

through the chosen rods (B/C) and the

Ceiling Canopy (D). Thread the Socket

Assembly (E), the chosen Rods (B/C) and

the Ceiling Canopy (D) together. Hand

tighten until snug.

Suggested rods for Ceiling height :

8’ ceiling : use (2) 12” rods

9’ ceiling : use (2) 6” rods and (2) 12” rods

STEP 2 - Installing the Crossbar Assembly

A. Pass the supply wires from outlet box through the Crossbar

Assembly (A). Attach the Crossbar Assembly (A) to the Outlet Box

with the head of the Green Ground Screw facing you. Secure the

Crossbar Assembly (A) with Outlet Box Screws (not included).

Tighten until snug.

Supply Wires with

Ground Wire

Outlet Box Screws

(not included)

Outlet Box

Figure 2

STEP 3 Test Fitting Ceiling Canopy to Crossbar Assembly-

eiling Canopy to the

ceiling

Remove mounting balls from the Crossbar Assembly (A). Fit the

C (D) Crossbar Assembly (A) and secure with

mounting balls. Note: The should be snug

against the and the mounting balls. If

Ceiling Canopy (D)

not, adjust the length

of the nipple on the Crossbar Assembly (A) by unscrewing the

preassembled hex nut and lock washer and then screwing the

mounting screws in or out of the crossbar until the correct length is

achieved. Once the Ceiling Canopy (D) is secure, remove the

mounting ball and Ceiling Canopy (D) and proceed to Step 4.

Mounting Screw

Hex Nut and

Lock Washer

Mounting Ball

Figure 3

Figure 1

Socket

Collar Tool

6” Rod

12” Rod

Supply Wires

and Ground Wire

Summary of content (2 pages)

PAGE 1
Assembly Instruction Sheet #IS-KGF1506BN For Style KGF1506BN 6 CORPORATE PARKWAY GOOSE CREEK , SC . 29445 www . quoizel . com Please go to www.quoizel.com for product cleaning tips. Go to the Care + Maintenance selection. Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
PAGE 2
KGF1506BN STEP 4 - Wire Connections A. Wrap bare or green ground wire around green ground screw on the crossbar, no less than 2 inches from the end of the wire. Tighten the green ground screw. B. Use standard wire connectors (not included) to make all wire connections. Twist connectors until wires are tightly joined together. Wrap each connection with approved electrical tape and carefully stuff all the connected wires into the Outlet Box.