Installation Sheet

ManualsBrandsQuoizel ManualsPendantsQuoizel Exhibit Single Light 7-3/4" Wide Outdoor Mini Pendant with Clear Glass Shade

1of2

Package Contents

Fixture Loop

Glass

Shade

Hardware Contents

Crossbar

Assembly

Ceiling

Canopy

Fixture Chain

Quick Link

STEP 2 Install Fixture Loop-

A. Thread the Fixture Loop (A) to

the nipple on the top end of the

Fixture Body (C). Hand tighten

until snug.

Figure 2

STEP 3 - Install the Crossbar Assembly to Outlet Box and Adjust

the length of the Nipple

A. Attach the Crossbar Assembly (AA) to the Outlet Box with the head

of the Green Ground Screw facing you. Secure it with Outlet Box

Screws (not included), tighten until snug

B. Adjust the hex nut and lock washer underside of the crossbar to the

middle of the nipple.

C. Remove the canopy lock ring from the canopy chain loop. Place the

Ceiling Canopy (DD) over the canopy chain loop against the ceiling

to determine the correct position of the nipple. Thread the canopy

lock ring onto the canopy chain loop. Adjust the nipple to allow the

Ceiling Canopy (DD) to rest against the ceiling when held in place by

the canopy lock ring.

D. Remove the canopy lock ring and the Ceiling Canopy (DD). Tighten

the lock washer and the hex nut against the crossbar to secure in

place.

Outlet Box Screw

(not included)

Hex Nut and

Lock Washer

Outlet Box

Green Ground Screw

Canopy Chain Loop

Canopy Lock Ring

Figure 3

Nipple

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.

Pleasegoto forproductcleaningtips.Gotothe selection.

(1)A21MediumBaseBulb150WMaximum,MediumBaseVintageBulbisrecommended,bulbnotincluded.

20-30minutes

Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtoensureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.

www.quoizel.com Care+Maintenance

LightSource:

EstimatedAssembly Time:

Preparation:

ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.

FixtureHangingHeight:MinimumHangingHeightis22.75”,MaximumHangingHeightis120”.

MissingParts?Contactyouroriginalplaceof

purchase.

Fixture Body

Lock Screw

Glass Holder

STEP 1 Install Glass Shade

and Glass Holder

A. Place the Glass Shade (B)

onto the Glass Holder (E). Lift

the Glass Holder (E) with the

Glass Shade (B) upward,

attach the top edge of the

Glass Shade (B) to the fixture

hood, and align mounting

holes on the side of the Glass

Holder (E) to holes on side

arms. Secure them together by

threading Lock Screws (D) into

mounting holes on the Glass

Holder (E). Hand tighten until

snug.

Fixture Hood

Side Arm

Figure 1

Installation Guide #IS-EXH1908EK

For Style EXH1908EK

2018 QuoizelInc.

ReleasedDate:2018-03-27

visit us on-line at www.quoizel.com

Summary of content (2 pages)

PAGE 1
Installation Guide #IS-EXH1908EK For Style EXH1908EK Please go to www.quoizel.com for product cleaning tips. Go to the Care + Maintenance selection. Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Light Source: (1) A21 Medium Base Bulb 150W Maximum, Medium Base Vintage Bulb is recommended, bulb not included. Fixture Hanging Height: Minimum Hanging Height is 22.75”, Maximum Hanging Height is 120”.
PAGE 2
STEP 4 - Install the Fixture Chain and Ceiling Canopy STEP 6 - Install the Bulb A. Adjust the Fixture Chain (BB) to your desired length by removing links if needed. Put a cloth over the Fixture Chain (BB) to protect the finish. B. Pull the supply wires through the Fixture Chain (BB) alternating links. After the wires are through the Fixture Chain (BB), pull the Supply Wires and the Ground Wire through the canopy lock ring and the Ceiling Canopy (DD) in order. C.