AWH Series Installation Guide

ManualsBrandsQMark ManualsCooling & Air QualityHeater 4000W Architectural Heavy-Duty Wall Heater, 240V/277V, Bronze

WH Series

Fan Forced Wall Heaters

For use with FRC and

AWH Series wall heaters

WHEN USING ELECTRIC APPLIANCES, BASIC PRECAU-

TIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE

RISK OF FIRE, ELECTRIC SHOCK, AND INJURY TO PER-

SONS, INCLUDING THE FOLLOWING:

1. Read all instructions before installing or using this heater.

2. This heater is hot when in use. To avoid burns, do not let

bare skin touch hot surfaces. Keep combustible materials,

such as furniture, pillows, bedding, papers, clothes, etc. and

curtains at least 3 feet (0.9 m) from the front of the heater.

3. Extreme caution is necessary when any heater is used by or

near children or invalids and whenever the heater is left

operating and unattended.

4. Do not operate any heater after it malfunctions. Disconnect

power at service panel and have heater inspected by a rep-

utable electrician before using.

5. Do not use outdoors.

6. To disconnect heater, turn controls to off, and turn off power

to heater circuit at main disconnect panel.

7. Do not insert or allow foreign objects to enter any ventilation

or exhaust opening as this may cause an electric shock, fire,

or damage to the heater.

8. To prevent a possible fire, do not block air intake or exhaust

in any manner.

9. A heater has hot and arcing or sparking parts inside. Do not

use it in areas where gasoline, paint, or flammable liquids

are used or stored.

10. Use this heater only as described in this manual. Any other

use not recommended by the manufacturer may cause fire,

electric shock, or injury to persons.

11. This heater is intended for comfort heating applications and

not intended for use in special environments. Do not use in

damp or wet locations such as marine or greenhouse or in

areas where corrosive or chemical agents are present.

12. When installing, see INSTALLATION INSTRUCTIONS for

additional warnings and precautions.

13. For safe and efficient operation, and to extend the life of your

heater, keep your heater clean - See MAINTENANCE

INSTRUCTIONS.

SAVE THESE INSTRUCTIONS

Installation, Operation & Maintenance Instructions

WARNING

IMPORTANT INSTRUCTIONS

ECR 41127 10/16 5200-11207-003

Table 1. Specifications

Min.

Supply

Model Wire

Number Volts Phase Watts Amps Gauge

WH3150FC 120 1 1500 12.5 12

WH3180FC 120 1 1800 15.0 12

WH4404*FC 240

4000/2000 16.7/8.3 10

208 3000/1500 14.5/7.2 12

WH4407*FC 277

4000/2000 14.5/7.2 12

240 3000/1500 12.5/6.3 12

WH4307*FC 277 1 3000/1500 10.8/5.4 12

WH4408*FC 208 1 4000/2000 19.2/9.6 10

WH44083FC 208 3 4000 11.1 14

WH44043FC 240 3 4000 9.7 14

*NOTE: Factory wired for higher wattage, field convertible to half wattage.

Min.

Supply

Model Wire

Number Volts Phase Watts Amps Gauge

WH4303FC 347 1 3000 8.6 14

WH4306FC 600 1 3000 5 14

WH4508FC 208 1 4800 23.1 10

WH4504FC 240 1 4800 20.0 10

208 3600 17.3

WH4507FC 277 1 4800 17.3 10

240 3600 15.0

WH45083FC 208 3 4800 13.3 12

WH45043FC 240 3 4800 11.6 14

WH4503FC 347 1 4800 13.8 12

WH4506FC 600 1 4800 8 14

*NOTE: Factory wired for higher wattage, field convertible to half wattage.

19-5/16"

(506.4mm)

15-3/4"

(400mm)

Conforms to

ANSI/UL 2021 and

CSA C22.2 No. 46

18-1/4"

(464mm)

14-3/8"

(365mm)

1-1/4"

(32mm)

Summary of content (20 pages)

PAGE 1
4-3/8" (365mm) 1-1/4" (32mm) 15-3/4" (400mm) WH Series 19-5/16" (506.4mm) Fan Forced Wall Heaters For use with FRC and AWH Series wall heaters 18-1/4" (464mm) Conforms to ANSI/UL 2021 and CSA C22.2 No. 46 Installation, Operation & Maintenance Instructions Table 1.
PAGE 2
INSTALLATION INSTRUCTIONS Installation of Back Box in New Construction 1. Mounting Back Box (See Figure 1) a. Place the back box between two 16" (406 mm) center-tocenter wall studs at the desired mounting height but no closer than 8" (203 mm) to adjacent wall or floor. Note: If wall studs are spaced greater than 16” on center, additional framing supports may be necessary. To prevent a possible fire, injury to persons or damage to the heater, adhere to the following: 1.
PAGE 3
a. Run a power supply cable into the area above the top of the wall opening. All wiring must be in accordance with National and Local electrical codes. Refer to Table 1, page 1 for correct wire size. Note to Installer: Converting heater to half wattage (Not applicable to WH3150FC and WH3180FC, 120 Volt Models) The WH Series wall heaters are manufactured and shipped at the higher rated wattage. Full wattage heaters can be converted to half wattage by doing the following steps. b.
PAGE 4
Installation of Heater Assembly and Grille TO RESET MANUAL RESET LIMIT: After back box is completely installed and no further construction dirt is expected, clean debris from back box and remove heater assembly from its carton. Then refer to Figure 5 and proceed as follows: Your heater is equipped with a manual reset safety thermal limit control that will automatically turn the heater off to prevent a fire if the heater overheats.
PAGE 5
Wiring Diagrams Diagram 5 Diagram 1 TRANSFORMER POWER ON/OFF 4800, 4000 & 3000 WATT HEATERS 347V OR 600V WIRING DIAGRAM FOR THREE PHASE WALL HEATERS FIELD WIRING Diagram 2 FAN MOTOR GND THERMOSTAT CYC L2 MANUAL RESET 1 FAN DELAY DISCONNECT POWER ON/OFF 2 3 1 8 6 0 4 2 RELAY ELEMENTS WIRING DIAGRAM FOR 4800 WATT 208 VOLT SINGLE PHASE WALL HEATER Diagram 3 POWER ON/OFF 1500, 1800,4800, 4000, & 3000 WATT HEATERS 120V, 208V, 240V, OR 277V (See diagram no.
PAGE 6
Replacement Parts Key No.
PAGE 7
NOTES: 7
PAGE 8
NOTAS/NOTES: 8
PAGE 9
14-3/8" (365mm) 1-1/4" (32mm) 15-3/4" (400mm) Serie WH Calefactores de pared con ventilador 19-5/16" (506.4mm) Para el uso con la FRC y Serie AWH calentadores 18-1/4" (464mm) Conforms to ANSI/UL 2021 and CSA C22.2 No. 46 Instrucciones de instalación, operación y mantenimiento Tabla 1.
PAGE 10
INSTRUCCIONES DE INSTALACIÓN Instalación de la caja posterior en una construcción nueva 1. Montaje de la caja posterior (vea la Figura 1). a. Coloque la caja posterior entre dos travesaños de la pared con una distancia entre centros de 406 mm (16”), a la altura de montaje deseada, pero a no menos de 203 mm (8”) de una pared adyacente y del piso. Para evitar un posible incendio, lesiones personales o daños al calefactor, observe lo siguiente: 1.
PAGE 11
Nota para el instalador: conversión del calefactor para potencia mtiad (no aplicable a los modelos WH3150 y WH3180 de 120 V) a. Tienda un cable de alimentación eléctrica hacia el área que está encima de la parte superior de la abertura de la pared. Todo el cableado debe hacerse de acuerdo con los códigos eléctricos nacionales y locales. Vea los calibres correctos de cables en la Tabla 1 de la página 1.
PAGE 12
Instalación del conjunto del calefactor y de la rejilla REPOSICIÓN MANUAL DEL LÍMITE TÉRMICO: Una vez que la caja posterior esté completamente instalada y no deba producirse más suciedad de construcción, limpie los desperdicios de la caja posterior y extraiga el conjunto de calefactor de su caja.
PAGE 13
Diagramas de conexionado Diagrama 1 MOTOR DEL VENTILADOR MOTOR DEL VENTILADOR TIERRA RETARDO DE VENTILADOR 1 Diagrama 5 CONEXIONADO DEL SITIO ENERGÍA DE ON/OFF 2 TRANSFORMADOR ELEMENTO CALEFACTOR 3 1 8 6 6 4 2 RELÉ ELEMENTOS CALEFACTORES TERMOSTATO CYC L1 TERMOSTATO LÍMITE TÉRMICO CON REPOSICIÓN MANUAL REPOSICIÓN MANUAL CALEFACTORES DE 4800, 4000 Y 3000 WATTS 347 V ó 600 V DIAGRAMA DE CONEXIONADO PARA CALEFACTORES DE PARED TRIFÁSICOS Diagrama 2 CONEXIONADO DEL SITIO MOTORDEL VEN
PAGE 14
Piezas de repuesto N° clave 1 2 3 4 5 6 7 8 — Descripción Número de pieza Conjunto de rejilla: : Blanco 2501-2003-004 Estándar 2501-2003-007 Elemento calefactor monofásico: 208V; 4000W 302015807 208/240V; 3000/4000W 302015808 240/277V; 3000/4000W 302012809 277V; 3000W 302012806 208V; 4800W 1802-2075-801 208/240V; 3600/4800W 302012810 240/277V; 3600/4800W 302012811 120V; 1500W 302012827 120V; 1800W 302012828 Elemento calefactor trifásico: 208V; 4000W 1802-2075-800 208/240V; 3000/4000W 1802-2075-802 208V;
PAGE 15
14-3/8" (365mm) 1-1/4" (32mm) 15-3/4" (400mm) Série WH 19-5/16" (506.4mm) Radiateurs muraux à air pulsé Pour une utilisation avec FRA et AWH série de radiateurs muraux Architectural 18-1/4" (464mm) Conforms to ANSI/UL 2021 and CSA C22.2 No.
PAGE 16
INSTRUCTIONS D'INSTALLATION Positionnement du boîtier arrière dans une construction neuve 1. Montage du boîtier arrière (Voir la Figure 1). a. Placez le boîtier arrière entre deux poteaux muraux adjacents avec un entraxe de16" (406 mm), à la hauteur de montage voulue, mais pas plus près de 8" (203 mm) du sol ou d’un mur adjacent. Pour éviter un possible départ d’incendie, des blessures corporelles ou des dommages au radiateur, respectez ces consignes : 1.
PAGE 17
a. Tirez un câble d’alimentation secteur dans la zone au-dessus du haut de l’ouverture murale. Tout le câblage doit être réalisé en conformité avec les normes électriques nationales et locales. Référez-vous au Tableau 1 en page 1 pour les bons calibres de fils. Note pour l’installateur : Conversion du radiateur à demi-puissance (Non applicable avec les modèles en 120 V, WH3150 et WH3180). Les radiateurs muraux de la série WH sont construits et livrés configurés pour la pleine puissance de sortie.
PAGE 18
Installation de l’ensemble de radiateur et de la grille RESTAURATION MANUELLE DU DÉPASSEMENT DE LIMITE : Une fois que le boîtier arrière est complètement installé et qu’aucune salissure due à la construction n’est à craindre, nettoyez les débris du boîtier arrière et sortez l’ensemble de radiateur de son carton d’emballage.
PAGE 19
Schémas de câblage Schéma 1 MOTEUR DE VENTILATEUR Schéma 5 CÂBLAGE SUR SITE MOTEUR DE VENTILATEUR TERRE RETARD DE VENTILATION 1 PUISSANCE ON/OFF TRANSFORMATEUR ÉLÉMENTS 2 3 1 8 6 6 4 2 RELAIS ÉLÉMENTS THERMOSTAT RESTAURATION MANUELLE DE LIMITE L1 CYC THERMOSTAT RESTAURATION MANUELLE RADIATEURS DE 4 800, 4 000 ET 3 000 WATTS EN 347 OU 600 VOLTS SCHÉMA DE CÂBLAGE POUR RADIATEURS MURAUX EN TRIPHASÉ Schéma 2 CÂBLAGE SURSITE MOTEURDE VENTILATEUR TERRE PUISSANCE ON/OFF THERMOSTAT CYC
PAGE 20
Pièces de rechange Réf.