Marine Grade In-Dash AM/FM Receiver with MP3 Playback & USB/SD/AUX Inputs USER’S MANUAL Receiver Models: PLRMR23BTW, PLRMR27BTB, PLMRKT36WT, PLMRKT46BK, PLMRKT38W, PLMRKT48BK - 0 -
COTENTS COTENTS ....................................................................................................................................................... 1 PRECAUTIONS .............................................................................................................................................. 2 Precautions & Warnings ........................................................................................................................ 2 Lithium Battery Cell Warnings..........
PRECAUTIONS Precautions & Warnings y To reduce the risk of fire, electric shock and interference, never attempt to repair this unit yourself. Refer all service to an authorized service centre. y Some MP3/WMA files may not be playable. y Keep the volume at a reasonable level to avoid distracted driving. High volume levels may make it difficult to concentrate on traffic and road conditions while driving.
INSTALLATION Installation Procedures First complete the electrical connections and then check that all connections are correct. Installation Opening This unit can be installed in any dashboard that has an opening as illustrated as below figure. 53 mm 182 mm To Install the Ship/Car Receiver Be sure to first test all connections and then follow these steps to install this unit. 1. Make sure the ignition is turned off and then disconnect the cable from the vehicle battery’s negative (-) terminal. 2.
Wiring Connections WIRING DIAGRAM Radio Antenna Socket FUSE 15A White: Front Left CH RCA Audio Output Red: Front Right CH RCA Audio Output Red: Rear Right CH RCA Audio Output White Front Left Speaker White: Rear Left CH RCA Audio Output CAUTION +12V DC NEGATIVE GROUND GND(Black) ACC (Red) Power B+(Yellow) ANT(Blue) White / Black Gray Front Right Speaker Gray / Black Green Rear Left Speaker Green / Black Purple Purple / Black Rear Right Speaker - Only use speakers with 4 ohms impedance.
CONTROL PANEL BUTTONS MUTE /MD MIC 1 4 RDM 2 INT 5 -10 RESET USB SD 6 +10 3 RPT BND AMS IR CLK 1. (power)/MODE (source) button 2. SEL (select/menu) button and VOL (volume) knob 3. button, BAND(band) button AMS (automatic store / preset station scan, automatic music search) button 4. (pause/play), Preset station 1 button 5. INT (intro), Preset station 2 button 6. RPT (repeat), Preset station 3 button 7. RDM (random), Preset station 4 button 8. -10(previous 10 tracks), Preset station 5 button 9.
GENERAL OPERATION Turn Unit On/Off 噝 Press the power ( turn off the unit. 噝 Press the power ( ) /MODE button on the front panel to turn on the unit, and long press it again to ) button on the remote control to turn the unit on or off. Adjust Volume (VOL) Rotate the VOL knob on the front panel or press the VOL+ increase or decrease the volume level.
Change the Source (MODE) Press the MODE button to switch between RADIO, BT(Bluetooth), USB(with USB device inserted), CARD(with SD card inserted) and AUX-IN(auxiliary input) modes. Mute on/off In power on mode, briefly press the MUTE button to toggle mute on or off. The muted state will be also released when the volume knob is used. Loudness on/off Press the LOUD button on the remote control to turn on the loudness to reinforce the output of bass frequencies, press again to turn it off.
RADIO OPERATION Switch Between USA area and Europe area Frequency In radio mode, press and hold the VOL/SEL button to enter switch state of the US(USA) and EU (Europe) frequency, then rotate it to switch between US(USA) and EU(Europe) frequency. The system will change the frequency setting in about 3 seconds. Change Bands (BAND) Press the BAND button to switch between the FM1, FM2, FM3, AM1 and AM2 bands. Each band stores up to six preset stations.
USB / SD CARD OPERATION To insert USB / SD CARD 噝 To play files on a USB device, open the USB port cover and insert the USB storage device into the USB port. Playback will begin automatically. 噝 Insert an micro SD card into the micro SD slot. Playback will begin automatically. Eject USB/SD 噝 To eject a USB device, press the button to stop playback, then remove the USB device.
BLUETOOTH OPERATION Pair and Connect Prior to using the Bluetooth device as a hands-free system for a Bluetooth-enabled mobile phone for the first time, you must pair and connect the two devices as follows: 1. In any mode, prior to pairing and connecting, the BT logo in the LCD indicating that no device is connected. To begin pairing, enable BT mode on your mobile phone. 2. When the phone finds this ship/car audio system, the “PYLE” name will be displayed. 3.
REMOTE CONTROL Remove Insulating Sheet The remote control comes with an insulating sheet attached to the underside of the remote control, as illustrated on the right. The remote control will not work until the insulating sheet is removed. Replace Lithium Battery Cell 1. When the lithium cell battery becomes weak, replace it as illustrated on the right. 2. Press and hold the movable block in the direction indicated by arrow 1.
SPECIFICATIONS General Chassis Dimensions..............................................................178(W) x 108(D) x 50(H) mm Power Supply Requirement ...................................................................................DC 12V Current Consumption .......................................................................................15A (max.) Maximum Power Output ..................................................................................
TROUBLESHOOTING If you suspect something is wrong, immediately switch power off. Do not use the unit in abnormal condition, for example without sound, or with smoke or foul smell, can cause fire or electric shock. Immediately stop using it and call the store where you purchased it. Never try to repair the unit by yourself because it is dangerous to do so. General 1) Ship’s/Car’s engine switch is not on. - Turn your Ship’s/car’s key to ACC or ON. 2) Cable is not correctly connected. - Check the connection.
